Advertisement
entry Delay time
The control unit has been set for a 20 second delay. You can change this to 0, 5, 10, 15, or 20
seconds.
1. Enter your password followed by the [PROG] button to enter the programming mode.
2. Press the [#/DOWN] button until "Entry" is flashing. Then select it by pressing the
[ARM/DISARM] button. Press the [*/UP] or the [#/Down] button to change it to the
number of seconds you want.
3. Press the [ARM/DISARM] button to confirm your choice.
retrieve History of alarm being triggered
You can get a list of the past five dates and times the unit has been activated by pressing the
[#/DOWN] button. Each time you press it, you will get the next number on the list.
retrieve Current list of telephone numbers on Call list
You can get a list of the numbers you programmed to call if the security system is triggered
by pressing the [*/UP] button. Each time you press it, you will get
the next number on the list.
HOW tO aDD aDDItIOnal aCCeSSOrIeS
The control unit needs to learn the signal of any new wireless accessory. The system has 10
zones which identify the location of the sensors. Zone 1 through 8 can learn one ID code
for each. Zone 9 can learn 8 ID codes, and Zone 10 is labeled "remote" and is reserved for
remote controls only. Up to 8 remote controls can be programmed into the control unit in
Zone 10.
Instructions for adding a new sensor:
1. Take the new sensor, put the battery/batteries in and bring to the control unit.
2. Enter the password followed by the [PROG] Button. Press the [#/Down] Button twice.
"Learn" should be flashing. Press [ARM/DISARM] to select.
3. Press the [*/UP] or the [#/Down] Button until the ID number shows at the bottom of the
LCD. Numbers
and
should say FULL from the two sensors that came with the unit.
2
1
"NO ID CODE" should be showing on the number you want to select. Press [ARM/DIS-
ARM] to select. Note: Each one of these numbers is considered a sensor zone.
4. To activate the sensor: For the Motion detectors wave a hand in front of it. For the Door/
Window Sensors move the magnetic sensors back and forth. (See step three section 2) For
the remote control, press any key. At this point you will hear a long beep that confirms the
selection.
5. If you need to delete a sensor, go to the sensor number you want to remove. It should say
"FULL" Press the [DEL/PAUSE] button to delete the code. Then activate a replacement
sensor and the unit will beep to confirm the new sensor.
6. See the sections in this manual for how to test and install each accessory.
Page 8
See macebrand.com for troubleshooting information.
lIMIteD Warranty
Seller warrants that this product is free from manufacturing defects, so we offer the origi-
nal purchaser a limited one-year warranty from original date of purchase on workman-
ship and materials. Seller will repair or replace, at its sole discretion, your product if
found, under normal use and proper care, to be defective. The decision to replace or repair
a product is made by the Seller after receipt of the defective product.
exClUSIOn Of WarrantIeS
LIABILITY OF THE SELLER UNDER THE SALE SHALL BE LIMITED TO THE RE-
PLACEMENT OF ANY DEFECTIVE GOODS. SELLER EXCLUDES, AND BUYER
HEREBY WAIVES, ALL WARRANTIES, GUARANTEES, AND OR LIABILITIES
NOT SET FORTH EXPRESSLY IN THIS AGREEMENT, WHETHER ARISING BY
LAW OR OTHERWISE (INCLUDING WITHOUT LIMITATION ANY OBLIGATION
OF SELLER WITH REGARD TO CONSEQUENTIAL AND INCIDENTAL DAM-
AGES) AND WHETHER OR NOT OCCASIONED BY SELLER'S NEGLIGENCE:
SELLER HEREBY EXCLUDES AND BUYER WAIVES, ALL WARRANTIES EX-
PRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, any IMPlIeD
Warranty Of MerCHantabIlIty OR FITNESS FOR INTENDED USE OR
FOR A PARTICULAR, PURPOSE AND EXCLUDES AND WAIVES RECOVERY OF
CONSEQUENTIAL AND INCIDENTAL DAMAGES.
®
Hide quick links:
Advertisement
