Mace 80355 Product Manual
  1. Manuals
  2. Brands
  3. Mace Manuals
  4. Security System
  5. 80355
  6. Product manual

Mace 80355 Product Manual

Wireless home security system
Hide thumbs Also See for 80355:
1
2
3
4
5
Table of Contents

Advertisement

Quick Links

See also: Product Manual
Enlarged version
Wireless Home Security System
Product Manual
(Model #80355)
Control Unit Description
1. Antenna Jack
6. Battery Low LED
2. Antenna
7. DC Power LED
3. LCD Display
8. Numerical Keys
4. Speaker
9. MIC
5. REC. /Play LED
10. Line jack
Overview
1. When the door/window sensor or motion detector is triggered, it sounds an alarm
and sends a signal to the control unit.
2. The control unit dials the first telephone number of your programmed list.
3. The person answering the call will hear the prerecorded alert message.
4. That person will have the option to listen in on the room, broadcast their voice
through the control unit, or disarm the system.
5. If there is no answer, or if the person does not disarm the security system, the unit
will dial the next number on your programmed list.
®
11. Telephone jack
12. DC 9V Power Jack
13. Buzzer
14. Reset button

InStallatIOn InStrUCtIOnS

During set-up, if no key is pressed for 15 seconds it will come out of the setup mode and
you will have to start over. You should first read the instructions before keying them in,
so that the unit will not time out.
See macebrand.com for troubleshooting information.

Safety tIPS

• Do not expose the system to direct sunlight or rain.
• Never place the unit close to your ear.
• Keep the unit away from radiators, heating ducts and stoves.
Do not permanently mount any of the pieces until following the testing directions to deter-
mine if the wireless system can communicate with all of the sensors.

SteP One: InStall tHe COntrOl UnIt

1. Remove the screw of main unit from battery compartment cover. Install a 9V battery
and replace cover. This provides back-up power in case of power failure. (Fig.1)
2. Plug the antenna into the plug labeled "ANT." on the side of the unit. (Fig.2)
3. Connect the included phone cord to the jack on the control unit labeled "LINE." Connect
the other end of the cord to your wall jack. (Fig. 3a)
4. You can also connect a phone to the unit by plugging it into the "TEL" jack. (Fig. 3a)
Check to see if you have a dial tone.
5. Plug the AC adapter into the DC9V socket on the control unit. (Fig 3b)
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 80355 and is the answer not in the manual?

Questions and answers

Mary Ross
February 11, 2025

our alarm is not arming and somehow the door sensor chimes whenever someone enters. How can we reset it? 80355 unit

0
1 comments:
Mr. Anderson
May 14, 2025

To reset the Mace 80355 alarm unit if it is not arming and the door sensor chimes when someone enters, press and hold the [PROG] button while using a pen to touch the window sensor. Then press [HOME] again to turn off the testing mode. If necessary, press the [RESET] button located on the back of the unit. The display will flash and return to normal, and the password will reset to the factory pre-set password “000.”

This answer is automatically generated

0

Related Manuals for Mace 80355

Summary of Contents for Mace 80355

  • Page 1: Installation Instructions

    You should first read the instructions before keying them in, so that the unit will not time out. Product Manual See macebrand.com for troubleshooting information. (Model #80355) Safety tIPS • Do not expose the system to direct sunlight or rain. • Never place the unit close to your ear.

  • Page 2: Program The Control Unit

    (Fig. 4) Go back to the control unit and press the [HOME] SteP tWO: PrOgraM tHe COntrOl UnIt button. After 60 seconds, return to the magnetic door/win- 1. Change the default password by pressing “000” followed by the [PROG] button. “Pass- dow sensor and separate the two sensors.

  • Page 3: Programming Telephone Numbers

    SteP SIx: PrOgraMMIng tHe telePHOne nUMberS 2. Mount the magnetic door/window sensor. Choose a suitable loca- We recommend using your cell phone as the first person on your list. Make sure you have tion, drill holes, and install anchors and screws. Place the unit over the permission from each person on your list to use their phone number.

  • Page 4: Additional Features

    auto Call feature baSIC OPeratIOnS The Auto Call feature is the part of the security system that calls the programmed phone • To activate the security system without the remote type in your password followed by the numbers if the sensors are triggered. By default, it is set to “on.” To change the Auto Call [ARM/DISARM] button.

  • Page 5: Limited Warranty

    See macebrand.com for troubleshooting information. entry Delay time The control unit has been set for a 20 second delay. You can change this to 0, 5, 10, 15, or 20 seconds. 1. Enter your password followed by the [PROG] button to enter the programming mode. 2.

Table of Contents