3 7 63 1515 0 SERVICE MANUAL CD RECEIVER MA121 2005 KD-G110,KD-S11 Area suffix J --------------- Northern America KD-G110 L 13942296513 KD-S11 TABLE OF CONTENTS PRECAUTIONS ............... 1-4 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
3 7 63 1515 0 SPECIFICATION KD-G110 AUDIO AMPLIFIER SECTION 18 W RMS × 4 Channels at 4 Ω and [< or =] 1% THD+N Power Output 80 dBA (reference: 1 W into 4 Ω) Signal to Noise Ratio 4 Ω...
Page 3
http://www.xiaoyu163.com KD-S11 3 7 63 1515 0 AUDIO AMPLIFIER SECTION 17 W RMS × 4 Channels at 4 Ω and [< or =] 1% THD+N Power Output 80 dBA (reference: 1 W into 4 Ω) Signal to Noise Ratio 4 Ω (4 Ω to 8 Ω allowance) Load Impedance Tone Control Range Bass...
http://www.xiaoyu163.com SECTION 1 3 7 63 1515 0 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 5
http://www.xiaoyu163.com Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
http://www.xiaoyu163.com SECTION 2 3 7 63 1515 0 SPECIFIC SERVICE INSTRUCTIONS HOW TO IDENTIFY MODELS 2.1.1 NAME PLATE Discernment sign (as same as KD-S11) 2.1.2 FRONT PANEL BACK SIDE Screw color J: SILVER J2: BLACK Screw L 13942296513 Screw Screw 2.1.3 FRONT CHASSIS ASSEMBLY Panel stopper color J: SILVER...
http://www.xiaoyu163.com SECTION 3 3 7 63 1515 0 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower right part of the front panel assembly and remove the front panel assembly. Front panel assembly Detach button Fig.1...
Page 8
http://www.xiaoyu163.com 3.1.4 Removing the side panel 3 7 63 1515 0 (See Fig.4) Reference: Remove the front panel assembly as required. (1) Remove the screw B and two screws C attaching the side panel on the left side of the main body. (2) Remove the side panel from the main body.
Page 9
http://www.xiaoyu163.com 3.1.7 Removing the CD mechanism assembly 3 7 63 1515 0 (See Fig. 7) • Remove the front panel assembly, bottom cover, side panel, rear bracket and main board. Reference: Remove the front chassis assembly as required. (1) Remove the three screws H attaching the CD mechanism assembly on the top chassis.
Page 10
http://www.xiaoyu163.com CD Mechanism Assembly 3 7 63 1515 0 3.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the two screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
Page 11
http://www.xiaoyu163.com 3.2.2 Removing the connector board 3 7 63 1515 0 Wires (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this in- struction may cause damage of the pickup. (1) Remove the screw B fixing the connector board.
Page 12
http://www.xiaoyu163.com 3.2.3 Removing the DET switch 3 7 63 1515 0 (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary. DET switch Connector board Pickup...
Page 13
http://www.xiaoyu163.com 3.2.4 Removing the chassis unit 3 7 63 1515 0 (See Figs.8 and 9) • Prior to performing the following procedure, remove the top Chassis unit cover and connector board. Suspension spring (L) Suspension spring (R) (1) Remove the two suspension springs (L) and (R) attaching the chassis unit to the frame.
Page 14
http://www.xiaoyu163.com 3.2.5 Removing the clamper assembly 3 7 63 1515 0 (See Figs.10 and 11) • Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. Clamper arm (2) Move the clamper assembly in the direction of the arrow to spring release the two joints d.
Page 15
http://www.xiaoyu163.com 3.2.6 Removing the loading / feed motor assembly 3 7 63 1515 0 (See Figs.12 and 13) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor assembly in the direction of the arrow to remove it from the chassis rivet assembly.
Page 16
http://www.xiaoyu163.com 3.2.7 Removing the pickup unit 3 7 63 1515 0 Pickup unit (See Figs.14 to 18) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from the pu.
Page 17
http://www.xiaoyu163.com 3.2.9 Removing the trigger arm 3 7 63 1515 0 Joint k (See Figs.19 and 20) • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release Trigger arm the joint k and pull out upward.
Page 18
http://www.xiaoyu163.com 3.2.11 Removing the mode sw. / select lock arm 3 7 63 1515 0 Link plate Joint t (See Figs.22 and 23) Mode sw. • Prior to performing the following procedure, remove the top plate assembly. Select lock arm (1) Bring up the mode sw.
Page 19
http://www.xiaoyu163.com 3.2.12 Reassembling the mode sw. / select lock arm 3 7 63 1515 0 Select lock arm spring (See Figs.24 to 26) REFERENCE: Hook w Reverse the above removing procedure. Joint v (1) Reattach the select lock arm spring to the top plate and set Joint v the shorter end of the select lock arm spring to the hook w on the top plate.
Page 20
http://www.xiaoyu163.com 3.2.13 Removing the select arm R / link plate 3 7 63 1515 0 Joint c' Link plate Joint r (See Figs.27 and 28) Select arm R Joint b' • Prior to performing the following procedure, remove the top plate assembly.
Page 21
http://www.xiaoyu163.com 3.2.15 Removing the loading roller assembly 3 7 63 1515 0 (See Figs.31 to 33) Loading roller assembly • Prior to performing the following procedure, remove the Roller guide clamper assembly and top plate assembly. spring (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly.
Page 22
http://www.xiaoyu163.com 3.2.16 Removing the loading gear 5, 6 and 7 3 7 63 1515 0 Loading gear bracket (See Figs.35 and 36) • Prior to performing the following procedure, remove the top Loading gear 6 cover, chassis unit, pickup unit and top plate assembly. (1) Remove the screw K attaching the loading gear bracket.
Page 23
http://www.xiaoyu163.com 3.2.17 Removing the gears 3 7 63 1515 0 Joint p' (See Figs.37 to 40) • Prior to performing the following procedure, remove the top Change plate cover, chassis unit, top plate assembly and pickup unit. rivet assembly • Pull out the loading gear 3. (See Fig.35.) (1) Pull out the feed gear.
Page 24
http://www.xiaoyu163.com 3.2.18 Removing the turn table / spindle motor 3 7 63 1515 0 Turn table (See Figs.41 and 42) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
(3) Digital tester Output Level Line out 2.0V (Vol. MAX) (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 Dummy load (6) Extension cable for check Exclusive dummy load should be used for AM,and FM. For FM EXTSH002-22P × 1 dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since...
SECTION 5 3 7 63 1515 0 TROUBLESHOOTING KD-G110 J and KD-S11 J version model 5.1.1 Feed section Is the voltage output at Is the wiring for IC561 Is 5V present at IC541 Check CD 8V. IC561 pin 22 5V or 0V...
Page 27
http://www.xiaoyu163.com 5.1.5 5.5 Signal processing section 3 7 63 1515 0 No sound from either Is the sound output from Compare the L-ch and channel. both channels (L, R)? R-ch to locate the defective point. Normal Is 9V present at IC301 pin Check the vicinity of the Q321 audio power supply.
Page 28
KD-G110 J2 and KD-S11 J2 version model 3 7 63 1515 0 5.2.1 Feed section Is the voltage output at Is the wiring for IC521 Is 5V present at IC561 Check CD 8V. IC521 pin 40, 5V or 0V...
Page 29
http://www.xiaoyu163.com 5.2.5 5.5 Signal processing section 3 7 63 1515 0 No sound from either Is the sound output from Compare the L-ch and channel. both channels (L, R)? R-ch to locate the defective point. Normal Is present at IC161 pin Check the vicinity of the IC901 audio power supply.
Page 30
http://www.xiaoyu163.com Maintenance of laser pickup 3 7 63 1515 0 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn of the power switch and, disconnect the with a alcohol soaked cotton swab.
Page 31
http://www.xiaoyu163.com 16 PIN CORD DIAGRAM 3 7 63 1515 0 Black Green BL/WH Violet Blue Gray WH/BK White Yellow GN/BK VI/BK GY/BK 16 YL MEMORY 8 BK 7 RD 5 BL/WH REMOTE 4 WH L 13942296513 12 WH/BK 3 GN 11 GN/BK 2 VI 10 VI/BK...
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA121) Printed in Japan http://www.xiaoyu163.com...
Page 33
3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-G110, KD-S11 CD-ROM No.SML200502 Area suffix J --------------- Northern America L 13942296513 KD-G110 KD-S11 Contents Block diagram (For J version) Standard schematic diagrams (For J version) Printed circuit boards (For J version)
http://www.xiaoyu163.com 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 35
http://www.xiaoyu163.com 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 TU.L-CH TU701 TU.R-CH FM/AM TUNER MICOM .MUTE Q861 MUTE Q332, Q432 CJ321 MUTING LINE OUT LINE OUT SD/ST MONO MUTE IC321 SSM,IFC POWER FM/AM AMP. FMOSC OUTLF, OUTLR S.METER OUTRF, OUTRR SEEK/STOP IC301 FRONT LEFT (+) E.VOLUME EACH BLOCK FRONT LEFT (-)
http://www.xiaoyu163.com 3 7 63 1515 0 Block diagram (For J2 version) Main amplifier & CD servo control section VF1, VF2, VT1 VT2, LD, MD PICK UP LM,MSW TRACKING+, BUS0 to 3 TRACKING- BUCK FOCUS+, FOCUS & IC561 IC521 FOCUS- TRACKING DSP &...
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 L-CH R-CH FM/AM TUNER FM/AM SD/ST MONO SK/ST1 Q781 Q341, Q351 MUTING J301 AMEO REARL, REARR LINE OUT DRIVE FMEO LINE OUT MUTING MUTE IC301 POWER AMP. OUTLF, OUTLR OUTRF, OUTRR MUTE IC161 FRONT LEFT (+) E.VOLUME EACH BLOCK FRONT LEFT (-)
Page 56
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA121SCH) http://www.xiaoyu163.com...
Exploded view of general assembly and parts list (Block No.M1) 3- 5 CD mechanism assembly and parts list (Block No.MB) 3- 7 Electrical parts list (Block No.01~02)(KD-G110,KD-S11_J) 3-10 Electrical parts list (Block No.03~04)(KD-G110,KD-S11_J2) 3-14 Packing materials and accessories parts list (Block No.M3)
Page 58
http://www.xiaoyu163.com 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 Switch board u163 http://www.xiaoyu163.com...
Page 59
http://www.xiaoyu163.com 3 7 63 1515 0 Main board L 13942296513 u163 http://www.xiaoyu163.com...
Page 60
http://www.xiaoyu163.com 3 7 63 1515 0 General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local GE10104-001A TOP CHASSIS GE40135-001A EARTH PLATE GE30938-003A SIDE PANEL QYSDST2604ZA TAP SCREW M2.6 x 4mm(x3) GE40235-001A SCREW (x2) QYSDST2604ZA TAP SCREW M2.6 x 4mm(x3) GE40235-004A SCREW...
Page 61
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism assembly and parts list Grease Block No. TN-2001-1011 TNG-87 GP-501MK CFD-005Z GP-305T L 13942296513 u163 The parts without symbol number are not service. http://www.xiaoyu163.com...
Page 62
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism Block No. [M][B][M][M] Symbol No. Part No. Part Name Description Local 30320101T FRAME 30320102T TOP COVER 30320115T DANPER F 30320116T DANPER R 303205505T CHASSIS RIVET 303205503T CHANGE P. RVT A 303205301T CLAMPER ASS'Y 303205302T SPINDLE MOTOR A...
Page 63
3 7 63 1515 0 Electrical parts list Main board(KD-G110,KD-S11_J) Symbol Part No. Part Name Description Local Block No. [0][1] C308 QEKJ1EM-475Z E CAPACITOR 4.7uF 25V M Symbol Part No. Part Name Description Local C309 QEKJ1AM-107Z E CAPACITOR...
Page 64
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C567 QEKJ1AM-107Z E CAPACITOR 100uF 10V M R336 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J C568 NCB31EK-104X C CAPACITOR 0.1uF 25V K R401 NRSA63J-223X...
Page 65
3 7 63 1515 0 Switch board(KD-G110,D-S11_J) Symbol Part No. Part Name Description Local Block No. [0][2] R797 NRS181J-100X MG RESISTOR 10Ω 1/8W J Symbol Part No. Part Name Description Local R798 NRSA63J-223X MG RESISTOR 22kΩ 1/16W J...
Page 66
3 7 63 1515 0 Main board(KD-G110,KD-S11_J2) Symbol Part No. Part Name Description Local Block No. [0][3] S601 NSW0124-001X TACT SW Symbol Part No. Part Name Description Local S602 NSW0124-001X TACT SW S603 NSW0124-001X TACT SW S604...
Page 67
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C165 NCB31CK-333X C CAPACITOR 0.033uF 16V K C536 NCB31EK-473X C CAPACITOR 0.047uF 25V K C166 NCB31HK-562X C CAPACITOR 5600pF 50V K C537 NCB31EK-473X...
Page 68
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R536 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R537 NRSA63J-472X MG RESISTOR...
Page 70
http://www.xiaoyu163.com 3 7 63 1515 0 Packing materials and accessories parts list Block No. No additional / supplemental order of WARRANTY CARDs are available. A3 A4 A5 A6 A7 A8 A16 L 13942296513 A9 A10 A11 A12 A13 u163 3-14 http://www.xiaoyu163.com...
Page 71
http://www.xiaoyu163.com 3 7 63 1515 0 Packing and Accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GE20137-005A-N MOUNTING SLEEVE G110J2 GE20137-003A MOUNTING SLEEVE G110J,S11J,S11J2 GE20135-010A TRIM PLATE G110J,G110J2 GE20135-009A TRIM PLATE S11J,S11J2 GET0251-001A INST BOOK ENG SPA FRE G110J,G110J2 GET0249-001A...