Table of Contents
Advertisement
CONNECTION/INSTALLATION
RM-P2580 System
System with up to 8 cameras
Camera
TK-C1430
Control signal cable
Video signal cable
Camera 1
AC24V
Power
MACHINE ID:1
or
(Menu screen)
cable
DC12V
RX TERM: OFF
Camera
(switch)
TK-C1430
Camera 2
AC24V
MACHINE ID:2
or
(Menu screen)
DC12V
RX TERM: OFF
(switch)
Camera
TK-C1430
Camera 8
AC24V
MACHINE ID:8
or
(Menu screen)
DC12V
RX TERM: ON
(switch)
CAMERA
POWER
Remote Control Unit
AC
INPUT
RM-P2580
This is the connected example of the TK-C1430E.
When controlling with any system except the RM-P2580, execute proper settings using
switches and menu screens according to the systems used. (
MEMO
• When operating a system using the RM-P2580, several cameras (up to 16) can be con-
nected and used on one control signal cable. Consequently, an incorrect switch setting on
just a single camera will cause the entire system to work incorrectly.
• Confirm switch settings on the screen as follows.
Confirm that the image from the camera to be checked
is displayed on the monitor.
Turn OFF and then ON the AC power to the camera to
be checked.
The camera begins the initial operation and characters
similar to those shown in the illustration on the right
appear on the monitor screen.
Confirm that "DUPLEX" and "ID-□□" are displayed and
that the ID number is the correct number (the number
should be the same as the number of the VIDEO IN-
PUT terminal to which the camera is connected on the
rear panel of the RM-P2580).
If wrong, set the camera ID again.
E-12
Time lapse VCR
CAM SW
•
•
•
•
•
OUT
SR-L910
REC
STOP/EJECT
REC
OPERATE
CHECK
VIDEO CASSETTE RECORDER
PAUSE/
OPE. LOCK
REVERSE
STILL
PLAY
COUNT/
SHIFT/TRACKING
RESET
CLOCK
MENU
/CANCEL
REW
FF
TIME
MODE
REC
TIMER
SET/V.LOCK
RESET
AL/PL
VIDEO IN
CAMERA
TO
SW
COM
TO CAMERA
TO CAMERA
DATA I / O
DATA I / O
UNIT
UNIT
CAMERA
CAMERA
SERIAL-1
SERIAL-1
SERIAL-2
SERIAL-2
RX+ RX
RX
RX- TX
TX+ TX
TX-
COM
COM
1
2
3
4
5
6
7
8
COM 9/1 10/2
COM
10/2 11/3
11/3 12/4
12/4 13/5
13/5 14/6 15/7
15/7 16/8 COM
COM
AUTO
AUTO
ALARM
ALARM
COM
COM
SW
COM
COM
OFF
MONITOR
VIDEO INPUT
VIDEO INPUT
1
2
3
4
5
6
7
8
MONITOR
MONITOR
MONITOR
MONITOR
OUTPUT 2
OUTPUT
OUTPUT
OUTPUT
OUTPUT
1
2
1 2
3
4
5 6
7
8
1
2
3
4
5
6
7
ON
ON
8
VIDEO OUTPUT
VIDEO OUTPUT
MONITOR
OUTPUT 1
Page 14)
MONITOR screen
(example showing camera ID as "05")
P R O T
O
C
O
L
:
D U P L E X
The number shown in the
"DUPLEX" should
□□ part of ID-□□
be displayed.
should be correct.
Connecting the control signal cable
(Use a twisted-pair cable for connection.
Camera 1
control signal
connection terminals
+
TX
A
TX
B
+
RX
C
RX
D
Camera 2
control signal
connection terminals
+
TX
A
TX
B
MONITOR
+
RX
C
RX
D
Setting the switches (
MONITOR
SET
CAMERA
AWC
SETUP
EXT TERM-OFF
MENU
NOT USED
Setting on the MENU screen (
* If the setting is changed, escape from the menu screen once, and definitely switch on the power again.
S T L E
MA H NE
When connecting
● Turn OFF the power supply to all equipment to be used before making connections.
I D - 0 5
● Carefully read the Instructions for each piece of equipment to be used before making
connections.
● For the appropriate connection cables and the length of these, carefully read "Connections
on the back" on page 16.
● The control signal cable cannot be used for loop connection.
Page 17.)
RM-P2580
Connect:
+
A RX
Camera TX+ to RM-P2580 RX+
B RX
Camera TX– to RM-P2580 RX–
+
C TX
Camera RX+ to RM-P2580 TX+
D TX
Camera RX– to RM-P2580 TX–
The
camera terminals and the RM-P2580 termi-
nals facilitate correct connections. Connect
the terminals with identical marks.
Page 10)
Select the synchronization method of the
camera image.
Set the switch on all cameras to LL (Line Lock)
and match with the V. PHASE.
(
Page 26.)
EXT TERM-OFF
ON
Set this switch to the DUPLEX
INT/GL
LL
* If the setting is changed, be absolutely sure to
DUPLEX
SIMPLEX
ON
RX TERM-OFF
ON
INT/GL
LL
switch on the power again.
DUPLEX
SIMPLEX
RX TERM-OFF
ON
NOT USED
Set this switch to ON (signal termination ON)
IRIS
VIDEO
DC
only on the camera placed at the end of the
control signal cable.
Set to OFF on all other cameras.
Page 35)
Set to M.DROP
C O
MM
UN I C A T I O N
Set to M.DROP when the RM-P2580 is used
Y
M . DROP
as a remote control unit. When controlling
C
I
I
D
1
from another machine, make sure that it
matches the communication system used.
MACHINE ID setting switches
Set this item to match the RM-P2580 VIDEO
INPUT terminal number for each camera.
marks indicated on both the
E-13
Advertisement
Table of Contents
