Table of Contents
Advertisement
BlackBox
R-1
Receiver
Package Contents
In addition to this manual:
1 pc, BlackBox R-512
1 pc, Power cord
1 pc, DC connector
1 pc, Standard antenna
1 pc, Antanna adaptor
2 pc, Trussholder brackets
DMX Interface
Transceivers on bus: 32 (max)
Data rate: 250 kbps (max)
ESD protection*: ±15 kV
AC input
90-250VAC 50/60Hz
1A at 115VAC (max)
0,5A at 230VAC (max)
DC input
12VDC 1,5A (max)
Compliance declarations
ETSI: EN300 328 & 300 826
EMC: EN301 489-17
CE:
EN60950
FCC: UQT-WDXOEMPCBF
IC:
6812A-WDMXOEM
ARIB: 06215559/AA/00
RF characteristics
Output power:
20
25** dBm
100 300** mW
Frequency range:
2402 to 2479 MHz
Channel bandwidth: 1
Sensitivity at 0.1% BER:
-95dBm
* Slewrate limited for
minimum of EMI in unter-
minated networks.
** Only in FCC output
power mode.
Installation
1 Attach the antenna to the connector on the front panel. If using
the standard antenna, use also the supplied adaptor.
2 Link the DMX source to the DMX in socket on the rear panel.
3 Connect power to the unit either via the AC power input (90 to
250VAC), the DC power input (12VDC) or via the DMX bypass
RJ45 socket (12VDC). If using the AC input, fit an appropriate
mains plug to the supplied power cord - this should be carried
out only by a qualified electrician.
4 If required, attach the supplied trussholder brackets to the top
cover of the unit (see page 12).
DC power input
(12VDC)
AC power input
(90-250VAC)
To link with a transmitter
1 Ensure that this receiver is not linked with any other transmitter
(
indicator should be OFF).
LINK
2 On the transmitter unit, press and release the
The transmitter will scan for all unlinked receivers for a period of
ten seconds.
3 If successful, the receiver's
more Level indicators will then show the signal strength.
To unlink from a transmitter
1 On the receiver, press and hold the
indicator goes OFF. The receiver is now unlinked.
LINK
RADIO
Indicates that Level
signal strength when linked to a transmitter
display is showing
signal strength
W-DMX
BATT
made in sweden
Not used
Radio
Batt
LINK
OFF: Not linked to a transmitter
ON: Linked to a transmitter
RAPID FLASH: Linking with a transmitter
Reserved
DMX out (RJ45)
1: DMX-
5: n/c
2: DMX+
6: n/c
3: n/c
7: Signal GND
4: n/c
8: n/c
indicator will go ON. One or
LINK
FUNCTION
Level
Provides indication of radio
TX
RX
Level
LINK
CTRL
DATA
POWER
W-DMX
Wireless Solution
made in sweden
FUNCTION
TX
RX
Radio
Level
LINK
CTRL
DATA
POWER
Batt
DATA
ON: Receiving DMX data
TX
CTRL
&
Not used
DMX out,
(XLR female 5pin)
DMX out, DC power in (RJ45)
1: DMX-
5: +12VDC
2: DMX+
6: n/c
3: n/c
7: Signal GND
4: +12VDC 8: DC GND
button.
FUNCTION
button until the
FUNCTION
Press for 5
seconds to unlink
from transmitter
Wireless Solution
Sweden AB
FUNCTION
R-512
Sweden AB
POWER
ON: Correct power
input present
Advertisement
Table of Contents
