Table of Contents
Advertisement
BlackBox S-1
Transmitter
Package Contents
In addition to this manual:
1 pc, BlackBox S-1
1 pc, Power cord
1 pc, DC connector
1 pc, Standard antenna
1 pc, Antenna adaptor
2 pc, Trussholder brackets
DMX Interface
Transceivers on bus: 32 (max)
Data rate: 250 kbps (max)
ESD protection*: ±15 kV
AC input
90-250VAC 50/60Hz
1A at 115VAC (max)
0,5A at 230VAC (max)
DC input
12VDC 1,5A (max)
Compliance declarations
ETSI: EN300 328 & 300 826
EMC: EN301 489-17
CE:
EN60950
FCC: UQT-WDXOEMPCBF
IC:
6812A-WDMXOEM
ARIB: 06215559/AA/00
RF characteristics
Output power:
20
25** dBm
100 300** mW
Frequency range:
2402 to 2479 MHz
Channel bandwidth: 1
Sensitivity at 0.1% BER:
-95dBm
* Slewrate limited for
minimum of EMI in unter-
minated networks.
** Only in FCC output
power mode.
Installation
1 Attach the antenna to the connector on the front panel. If using
the standard antenna, use also the supplied adaptor.
2 Link the DMX source to the DMX in socket on the rear panel.
3 Connect power to the unit either via the AC power input (90 to
250VAC), the DC power input (12VDC) or via the DMX bypass
RJ45 socket (12VDC). If using the AC input, fit an appropriate
mains plug to the supplied power cord - this should be carried
out only by a qualified electrician.
4 If required, attach the supplied trussholder brackets to the top
cover of the unit (see page 12).
DC power input
(12VDC)
IMPORTANT
AC power input
Only one DMX
universe input
(90-250VAC)
may be connected
at any time
To add receivers
Note: You can add receivers at any time, even during operation.
1 Power on the receiver unit(s) and ensure that they are not linked
with any other transmitter (
2 On the transmitter unit, press and release the
The transmitter will scan for all unlinked receivers for a
period of ten seconds - the
3 If successful, each receiver's
failed, check that the receiver is in range and repeat procedure.
To unlink all receivers
1 On the transmitter, press and hold the
begins flashing. All registered receivers will be unlinked.
LINK
RADIO
ON: Indicates that
Level display is
W-DMX
showing signal
made in sweden
strength
Radio
BATT
Not used
Batt
LINK
ON: Normal operation
FLASH: Unlinking all receivers
RAPID FLASH: Linking with receivers
Reserved
DMX bypass,
(XLR female 5pin)
DMX in (RJ45)
1: DMX-
5: n/c
2: DMX+
6: n/c
3: n/c
7: Signal GND
4: n/c
8: n/c
indicators should be OFF).
LINK
indicator will flash rapidly.
LINK
indicator will go ON. If any
LINK
FUNCTION
Level
Provides indication
of radio output signal strength
TX
RX
Level
LINK
CTRL
DATA
POWER
W-DMX
Wireless Solution
made in sweden
TX
RX
Radio
Level
LINK
CTRL
DATA
POWER
Batt
DATA
ON: Transmitting DMX data
RX
CTRL
&
Not used
DMX in,
(XLR male 5pin)
DMX bypass, DC power in
1: DMX-
5: +12VDC
2: DMX+
6: n/c
3: n/c
7: Signal GND
4: +12VDC
8: DC GND
button.
FUNCTION
button until
FUNCTION
Press and release
to search for and
Wireless Solution
link with receivers
Sweden AB
FUNCTION
S-1
Sweden AB
FUNCTION
POWER
ON: Correct power
input present
Advertisement
Table of Contents
