Page 1
Laser Barcode Scanner For power supply, the charging cradle of LS6000B-U also works as a battery charger for the scanner. Users can plug in 5V DC power adaptor for power charge of the scanner.
Page 2
6 hours at first time before install driver. 2. Install the software “PL-2303 Driver Installer.exe” to the host system for LS6000B-U series. No need to key-in 3. Connect scanner cradle to the USB port on the host Step 1: key-in the identify system.
7. Start to aim the scanner at a bar code, you may see data shown on the hyper terminal. FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable Reset Configuration to Defaults protection against harmful interference when the equipment is operated in a commercial environment.
Multi-Interface Functions – 1 OUTPUT FIRMWARE VERSION RESET CONFIGURATION TO DEFAULTS OUTPUT OUTPUT MODE – KEYBOARD / USB OUTPUT MODE - SERIAL MODE 000600 000601 BUZZER / GOOD READ BEEP TONE – NONE GOOD READ BEEP TONE - RESET 014200 0B142 Setup from Bar Code Label IMAGE...
Page 5
Multi-Interface Functions – 2 Interface – KBW READING SCAN MODE – SINGLE SCAN SCAN MODE – SINGLE SCAN NO MODE TRIGGER Communication WEDGE MODE - AUTODETECT WEDGE MODE – SCAN SET 2 PASS THRU 013300 013301 SCAN MODE – MULTISCAN SCAN MODE –...
Page 6
Interface – Serial - 1 Interface – Serial - 2 BAUD RATE PARAMETERS SERIAL BAUD RATE - 2400 SERIAL BAUD RATE - 4800 SERIAL DATA BITS - 8 SERIAL DATA BITS - 7 00081 00080 000703 000704 SERIAL STOP BITS - 2 SERIAL STOP BITS - 1 SERIAL BAUD RATE - 9600 SERIAL BAUD RATE - 19200...
Symbologies Set Up - 1 Symbologies On/Off - 3 CODE 11 CODE 11 ID CHARACTER – “m” CODE 11 ID CHARACTER – “Z” MSI - ENABLE MSI - DISABLE 0131m 0131Z 01151 01150 CODE 11 LASER/CCD REDUNDANCY - CODE 11 LASER/CCD REDUNDANCY - UPC/EAN ENABLE DISABLE...
Page 9
Symbologies Set Up – 2 Symbologies Set Up – 3 CODE 93 CODABAR CODABAR ID CHARACTER –‛k’ CODABAR ID CHARACTER –‛Z’ CODE 93 ID CHARACTER – “h” CODE 93 ID CHARACTER – “Z” 0094k 0094Z 0066h 0066Z CODABAR LASER/CCD REDUNDANCY CODABAR LASER/CCD CODE 93 LASER/CCD REDUNDANCY - CODE 93 LASER/CCD REDUNDANCY -...
Page 10
0113j 0113Z 00481 00480 Symbologies Set Up – 4 ID2OF5 LASER/CCD REDUNDANCY - ID2OF5 LASER/CCD REDUNDANCY - ENABLE DISABLE 01141 01140 MSI CHECK DIGIT – MOD 10 MSI CHECK DIGIT –RESET 01160 0B116 MSI ISBN ID CHARACTER –‛f’ MSI ISBN ID CHARACTER –‛Z’ 0053f 0053Z MSI LASER/CCD REDUNDANCY -...
Page 11
Symbologies Set Up – 5 Symbologies Set Up – 6 SEND UPC-A CHECK DIGIT ENABLE SEND UPC-A CHECK DIGIT DISABLE EAN-8 ID CHARACTER ‛d’ EAN-8 ID CHARACTER ‛Z’ UPC/EAN 00421 00420 0052d 0052Z SEND UPC-E CHECK DIGIT ENABLE SEND UPC-E CHECK DIGIT DISABLE ISBN ID CHARACTER ‛f’...
EDIT SETUP BAR CODES MACRO/SPECIAL KEYS SETUP BAR CODES EDIT #1 – STRIP 1 LEADING CHARACTER EDIT #1 - OFF MACRO #1 – FIND ‛1’ AND REPLACE WITH MACRO #1 - DISABLED ON ALL BAR CODES THAT START WITH ‛ONE’ ‛12345’...
Page 14
Scanner Timing Default RS-232 communication Default Baud rate 9600 Parity None Data Bits Stop Bit RTS/CTS Terminator <CR> Keyboard Wedge Communication Default Terminal Type PC/AT Keyboard US keyboard Appendix-A Terminator Enter (Alpha numeric) USB Communication Default Troubleshooting & Error Beeps Terminator type Enter Code mode...
Page 15
a. Problem: Nothing happens when I follow the operating instructions. d. My computer gets a keyboard error while booting up. Possible Cause Possible Solution Possible Cause Possible Solution Interface cables are loose Check for loose cable connections The scanner is damaged or is no Disconnect the scanner from your longer functioning.
Page 16
Problem: The scanner beeps, but no data is displayed on my computer. h. Problem: Some of the barcode data is missing displayed on the host. Possible Cause Possible Solution Possible Cause Possible Solution Scanner is not programmed for the Please make sure the scanner is The scanner’s transmit speed is too For RS232, you can set up the correct host type.
Page 17
Version: 2.0 Date: November 11, 2008 P/N: 79.60002.101...