APW Wyott HOTROD Product Manual page 2

THIS MANUAL SHOULD BE RETAINED FOR FUTURE REFERENCE
! CAUTION
These models are designed, built and sold for commercial use. If these models are positioned
so the general public can use the equipment, make sure that all cautions, warnings and oper-
ating instructions are clearly posted near each unit so that anyone using the equipment will
use it correctly and not injure themselves or harm the equipment.
CHECK THE DATA PLATE ON THIS UNIT BEFORE INSTALLATION. CONNECT THE UNIT
ONLY TO THE VOLTAGE AND FREQUENCY LISTED ON THE DATA PLATE. CONNECT
ONLY TO 1 OR 3 PHASE AS LISTED ON THE DATA PLATE.
!
Improper installation, operation, service or maintenance can cause property damage, injury or
death. Read these instructions thoroughly before installing, operating, maintaining or servicing
this equipment.
!
ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE
PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL CODES.
!
DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT
SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.
Install according to the spacing requirements listed in the installation section of this manual.
We strongly recommend having a competent professional install this equipment. A licensed
electrician should make the electrical connections and connect power to the unit. Local codes
should always be used when connecting these units to electrical power. In the absence of
local codes, use the latest version of the National Electrical Code.
Maintenance and repair should be handled by a factory authorized agent. Before doing any
maintenance or repair, contact APW/Wyott.
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All containers should be examined for damage before and during unloading. The freight car-
rier has assumed responsibility for its safe transit and delivery. If equipment is received dam-
aged, either apparent or concealed, a claim must be made with the delivering carrier.
A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must
then be signed by the carrier representative (Driver). If this is not done, the carrier may refuse
the claim. The carrier can supply the necessary forms.
B) If there is concealed damage or loss, if not apparent until after equipment is uncrated, a
request for inspection must be made to the carrier within 15 days. The carrier should arrange
an inspection. Be certain to hold all contents and packaging material.
Installation and start-up should be performed by a qualified installer who thoroughly read,
understands and follows these instructions.
If you have questions concerning the installation, operation, maintenance or service of this
product, write Technical Service Department APW/Wyott Foodservice Equipment Company,
P.O. Box 1829, Cheyenne, WY 82003.
! WARNING
WARNING
WARNING
WARNING
2
ITEM DESCRIPTION PART NO.
15 MOTOR GEAR 217485-10
16 DRIVE MOTOR FAN 12065-10
18 TIE ROD, SLANT UNITS 217488-20
217488-30
217488-31
217488-50
19 FOOT, RUBBER 217014-61
FOOT, 1" ADJUSTABLE 86621-00
INSERT FOR ADJ. FOOT 84840-00
20 DRIP PAN 217484-20
217484-30
217714-12
217484-50
217714-20
217524-88
21 ELEMENT RETAINER 217481-00
217490-00
217714-22
217524-91
22 ELEMENT SUPPORT 217480-00
217491-00
217714-24
217524-90
23 SCREW, #6-32 X 1-3/4 81139-00
24 #6 LOCK WASHER 85015-00
25 FLAT WASHER 85072-00
26 #6-32 KEPS NUT 84001-00
27 #8-32 X 3/8 HEX HD SCREW 81531-00
28 #8-32 X 3/8 PAN HD SCREW 81300-00
29 #10-32 KEPS NUT 84171-00
UNIT
ALL UNITS
ALL UNITS
FOR "-20" UNITS
FOR "-30" UNITS
FOR "-31" UNITS
FOR "-50" UNITS
FOR "-20" UNITS
FOR "-30" UNITS
FOR "-31" UNITS
FOR "-50" UNITS
FOR "-45" UNITS
FOR "-75 & -85" UNITS
ALL FLAT "-20, -30, -31, -50"
ALL SLANT "-20, -30, -31, -50"
FOR "-45 & -75" UNITS
FOR "-85" UNITS
ALL FLAT "-20, -30, -31, -50"
ALL SLANT "-20, -30, -31, -50"
FOR "-45 & -75" UNITS
FOR "-85" UNITS
MOTOR HARDWARE
MOTOR HARDWARE
MOTOR HARDWARE
MOTOR HARDWARE
FOR ELEMENTS
FOR BOTTOM PANEL
FOR ELEMENT SUPPORTS
11