Before Requesting Service - Panasonic NV-FJ615 Series Operating Instructions Manual

Before Requesting Service

Before requesting service, please check the following points.
√ √ √ √ √ On Screen Display Messages
The error messages are given in brackets [ ].
[Please insert video tape!]
' You pressed the REC button J (REC/OTR button c),
the DIRECT TV REC button 6, the Play button I, the
Fast Forward button H, the Rewind button 8 or the
SEARCH button M when no cassette was inserted in
the VCR.
You pressed the TIMER REC button D when no
cassette was inserted in the VCR with a timer recording
programmed.
Insert a video cassette.
[Please use tape with unbroken recording tab!]
' You pressed the REC button J (REC/OTR button c) or
the DIRECT TV REC button 6 when a cassette with a
broken out erasure prevention tab was inserted in the
VCR.
You pressed the TIMER REC button D when a cassette
with a broken out erasure prevention tab was inserted
in the VCR with a timer recording programmed.
Insert a video cassette with an intact erasure
prevention tab on which recording is possible.
[This action is not possible before time and date are set]
' You pressed the SHOW VIEW button L or the PROG./
CHECK button <, even though the time and date have
not yet been set on the VCR.
Set the time and date.
[No timer programmes to be done!]
' You pressed the TIMER REC button D even though no
timer recording has been programmed.
Programme a timer recording before pressing the
TIMER REC button D.
[Please put VCR into stop mode first]
' You attempted to change the contents of the timer
programming while a timer recording was being
performed.
Put the VCR into the stop mode first.
Other messages may also appear.
Follow the instructions given on the TV screen.
42
√ √ √ √ √ The VCR Does Not Work Correctly
The symptom descriptions are given between quotation
marks " ".
"The VCR display is not illuminated."
' The AC mains lead is disconnected.
Connect the AC mains lead securely.
' VCR display setting is "OFF". Set "VCR display" to "ON"
or "DIMMED". (See page 37.)
' Power save setting is "ON". Set "Power save" to "OFF".
(See page 37.)
"The VCR display is illuminated, but the VCR cannot be
operated."
' The VCR is in the timer recording standby mode.
Press the TIMER REC button D to cancel the standby
mode.
' Safety devices are operating.
Disconnect the AC mains lead and wait approximately
1 minute before reconnecting.
Then check if the VCR can be operated.
"The VCR picture does not appear on the TV screen."
' The RF output channel is set to [– –].
Change the RF output channel to a channel other than
[– –]. (See page 12.)
"Auto clock setting does not work correctly."
' Teletext information is not available or cannot be read.
Set the clock manually.
"Download cannot be performed."
' The VCR is not connected to a TV equipped with the
Q Link (or a similar) function via a fully-wired 21-pin
Scart cable.
Be sure to use a fully wired 21-pin Scart cable to
connect the VCR to a TV with the Q Link (or a similar)
function.
√ √ √ √ √ Playback Does Not Work Properly
The symptom descriptions are given between quotation
marks " ".
"The playback picture is distorted or in black and white.
Or, horizontal noise bars appear in the picture or horizontal
lines move up and down."
' The tracking adjustment is not correct.
Adjust the tracking. (See page 44.)
' The TV's video playback channel has not been tuned
correctly.
Re-tune the video playback channel.
' The video heads are clogged or worn.
Consult your dealer for advice.
' The playback picture is distorted when using an E300
type video cassette that was recorded in the LP mode.
We recommend that you use video cassettes other than
type E300.
' SQPB setting is not correct.
Set SQPB setting correctly. (See page 38.)