Advertisement
Quick Links
R
& F
EAD
OLLOW
W
ARNINGS
B
EFORE
This burnisher will afford you many years of
trouble free operating satisfaction if it is
given proper care. All parts have passed
rigid quality control standards before being
assembled to produce the finished product.
Prior to packaging, the units again inspect-
ed for assurance of flawless assembly.
Your burnisher was protectively packed to
prevent damage in shipment. We recom-
mend that upon delivery, remove the unit
from its carton and carefully inspect it for
any possible damage in transit.
S
AVE
A
I
LL
& C
AUTIONS
U
T
SING
HIS
If damage is discovered, immediately notify
the transportation company that delivered
your burnisher. As a shipper, we are
unable to act upon any claim for concealed
damage. You must originate any claim
within 5 days of delivery.
These instructions are for your protection
and information. PLEASE READ CAREFUL-
LY! Failure to follow these precautions could
result in injury or discomfort.
T
I
HESE
NSTRUCTIONS
1500 C
NSTRUCTIONS
B
URNISHER
P
1
AGE
Contractor Burnisher Manual - PN 408794 - Printed in USA 11/20/06
ONTRACTORS
B
URNISHER
S
O
PERATION
M
AINTENANCE
M
/P
W
ARTS
This unit is intended for commercial use.
,
I
NSTRUCTIONS
O
,
AFETY
&
ANUAL
L
IST
R
A
EAD
LL
B
EFORE
PERATING
Advertisement
Related Manuals for MasterCraft 1500 Contractors
Summary of Contents for MasterCraft 1500 Contractors
- Page 1 1500 C ONTRACTORS URNISHER AFETY & PERATION AINTENANCE ANUAL ARTS This unit is intended for commercial use. & F OLLOW NSTRUCTIONS & C ARNINGS AUTIONS EFORE SING URNISHER This burnisher will afford you many years of If damage is discovered, immediately notify trouble free operating satisfaction if it is the transportation company that delivered given proper care.
- Page 2 MPORTANT ARNING AFETY To reduce the risk of fire, electric shock or injury: NSTRUCTIONS When using an electric burnisher, basic precautions should always be following, including the following: 1) DO NOT leave burnisher plugged in 6) DO NOT pull or carry by the cord, use 11) DO NOT operate where oxygen or when not in use.
- Page 3 ARNING Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. DO NOT modify the plug provided with the burnisher. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
- Page 4 PERATING ARNING NSTRUCTIONS To avoid fire, DO NO use with a flammable or combustible liquid to clean a floor. This burnisher can be used in conjunc- 5) Never leave burnisher resting on buff- 3) Before turning burnisher on, run tip tion with any of the ultra high speed ing pad for an extended period of time.
- Page 5 ANDLE SSEMBLY & RAWING EPLACEMENT ARTS __________________________________ Part Description Part __________________________________ Handle Assembly 368393 Ribbed Handle Grip 324744 Handle Bar 376612 Switch Box Cover 376647 #12-24 Hex Nut 376744 Trigger Pin 376701 Roll Pin 383139 Extension Spring 376671 #8-32 X "...
- Page 6 & C OTOR HASSIS RAWING...
- Page 7 & C OTOR HASSIS EPLACEMENT ARTS _____________________________________ _____________________________________ Part Part Part Description Part Description _____________________________________ _____________________________________ Grommet 369330 - 16 Locknut 423076 Electrical Wire Connector 385425 .37 Split Lockwasher 368849 Brush Wear Indicator Light 386448 Steel Wave Washer 374059 Canopy Screw 380059 "...
-
Page 8: Care And Maintenance
This burnisher requires limited maintenance 3) Unplug burnisher and check power cord for proper operation and years of service. for and breaks in the wire. Breaks will most likely occur near the plug or switch. Any AINTENANCE 1) After each use, wipe off all of the polished breaks should be repaired or replaced and painted areas with a clean cloth.
Need help?
Do you have a question about the 1500 Contractors and is the answer not in the manual?
Questions and answers