Page 1 V10.2.00...
Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4 Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux- embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov- enia.
Page 5: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 6: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 7: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 8: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 9 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 10: Power Safety
Preface Power Safety The computer has specific power requirements:  • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, Power Safety uninterrupted power supply.
Page 11: Polymer Battery Precautions
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha- nism and is not a cause for concern.
Page 12: Battery Precautions
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 13: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 14: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 15 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 16 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 17: Lcd Screen Care
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 18 Preface...
Page 19: Table Of Contents
Preface Contents Notice .................I Function/Hot Key Indicators .........1-9 FCC Statement ..............III System Map: Front & Rear Views .......1-10 FCC RF Radiation Exposure Statement: ......IV LED Indicators .............1-10 Instructions for Care and Operation ....... VI System Map: Left View ..........1-11 Power Safety ..............
Page 20 Preface Gestures .................2-9 Conserving Battery Power ...........3-12 Audio Features .............2-10 Battery Life ..............3-13 VIA HD Audio Deck ...........2-11 New Battery ..............3-13 Realtek HD Audio Manager ........2-13 Recharging the Battery with the AC/DC Adapter ..3-13 Optimizing Audio Recording ........2-14 Proper handling of the Battery Pack ......3-14 Adding a Printer ............2-15 Battery FAQ ..............3-15 USB Printer ..............2-15...
Page 21 Preface Wireless LAN Module ...........4-8 Bluetooth Power Setting (Advanced Menu > PC Camera Module ............4-8 Advanced Chipset Control) ...........5-8 3.75G/HSPA Module .............4-8 SATA Mode Selection (Advanced Menu) .....5-9 Bluetooth Module ............4-8 Legacy USB Support (Advanced Menu) .......5-9 Boot-time Diagnostic Screen (Advanced Menu) ...5-9 BIOS Utilities Power On Boot Beep (Advanced Menu) .......5-9 Battery Low Alarm Beep (Advanced Menu) ....5-9...
Page 22 Preface 802.11b/g/n WLAN Driver Installation ......7-3 Bluetooth Configuration in Windows 7 .......7-52 Connecting to a Wireless Network ........7-4 Troubleshooting Windows Mobility Center ..........D-7 PC Camera Module ............7-8 Overview ................8-1 PC Camera Driver Installation ........7-9 Basic Hints and Tips ............8-2 3.75G/HSPA Module ...........7-15 Backup and General Maintenance .........8-3 Mobile Partner .............7-17...
Page 23 Preface Specifications Windows XP Information Processor ............... C-2 Windows XP Start Menu & Control Panel ....D-2 Core Logic ..............C-2 TouchPad and Buttons/Mouse ........D-3 Display ................C-2 Function/Hot Key Indicators ........D-4 Memory ................. C-2 Audio Features ..............D-5 Video Adapter ............... C-2 VIA HD Audio Deck .............D-6 BIOS ................
Page 24 Preface Battery Information ............ D-24 PC Camera Driver Installation ........D-37 New Battery ..............D-24 3.75G/HSPA Module ..........D-38 Battery Life ..............D-24 Mobile Partner Application Installation .....D-39 Recharging the Battery with the AC/DC Adapter ..D-25 BandLuxe HSDPA Utility Installation .......D-40 Proper handling of the Battery Pack ......D-26 Bluetooth Module ............
Page 25: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 26: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Driver Installation (WIN7)” on page 4 - 2/“Driver Installation (WINXP)” on page D - “BIOS Utilities”...
Page 27: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.  Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers &...
Page 28: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7 operating system version as indicated below.
Page 29: System Startup
Quick Start Guide System Startup Remove all packing materials, and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Page 30: System Map: Lcd Panel Open (Models A, B & C)
Quick Start Guide System Map: LCD Panel Open (Models A, B & C) Figure 1 - 2 LCD Panel Open  (Models A, B & C) Wireless Device Built-In PC Camera Operation Aboard Aircraft Keyboard Built-In Microphone The use of any portable elec- tronic transmission devices Touchpad &...
Page 31: System Map: Lcd Panel Open (Model D)
Quick Start Guide System Map: LCD Panel Open (Model D) Figure 1 - 3 LCD Panel Open  (Model D) Wireless Device Built-In PC Camera Operation Aboard Aircraft Power Button Keyboard The use of any portable electronic transmission Built-In Microphone devices aboard aircraft is Touchpad &...
Page 32: Keyboard
Quick Start Guide Keyboard The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 2, on page 1 - 9 for details on the function keys. ...
Page 33: Function/Hot Key Indicators
Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Keys Function Keys Function Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle 3.75G Module Power Brightness Decrease/...
Page 34: System Map: Front & Rear Views
Quick Start Guide System Map: Front & Rear Views Figure 1 - 5 Front & Rear Views LED Indicators Battery LED Indicators Icon Color Description Orange DC Power is Plugged In Table 1 - 3 Green The Computer is On LED Indicators Blinking Green The Computer is in Sleep Mode...
Page 35: System Map: Left View
Quick Start Guide System Map: Left View Figure 1 - 6 Left View Security Lock Slot DC-In Jack Vent/Fan Intake/ Outlet USB 2.0 Port   Microphone-In Jack Headphone-Out Overheating External Optical (CD/DVD) Device Drives Jack To prevent your computer from To install applications and drivers etc.
Page 36: System Map: Right View
Quick Start Guide System Map: Right View Figure 1 - 7 Right View Multi-In-1 Card Reader 2 * USB 2.0 Ports RJ-45 LAN Jack External Monitor  Port Power Button External Optical (CD/DVD) Device Drives (Models A, B & C Only) To install applications and drivers etc.
Page 37: System Map: Bottom View
Quick Start Guide System Map: Bottom View Figure 1 - 8 Bottom View Battery Component Bay Cover Vent/Fan Intake/ Outlet Speakers   3.75G/HSPA Module USIM Card The 3.75G/HSPA module’s USIM card location is located under the battery compartment. See page 1 - 14 for instructions on installing the 3.75G/HSPA USIM card.
Page 38: 3.75G/Hspa Module Usim Card Installation
Quick Start Guide 3.75G/HSPA Module USIM Card Installation If you have included an optional 3.75G/HSPA module in your purchase option, follow the instructions below to install the USIM card (which will be provided by your service provider), and then run the appropriate applica- tion.
Page 39: Windows 7 Start Menu & Control Panel
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (For information on Windows XP see pendix D) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 40: Video Features
Quick Start Guide Video Features You can configure display options from the Display (Control Panel) and Screen Resolution in Windows. For more detailed video information see Chapter B“Intel Video Driver Controls” from page B - To access Display (Control Panel) and Screen Resolution in Windows: Click Start and click Control Panel.
Page 41: Screen Resolution & Intel Gma Control Panel
Quick Start Guide Screen Resolution & Intel GMA Control Panel Figure 1 - 11 - Screen Resolution & Intel GMA Driver for Mobile Control Panel Video Features 1 - 17...
Page 42: Power Options
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 15) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu.
Page 43: Mofa Lcd Back Covers
Quick Start Guide MOFA LCD Back Covers MOFA (Magic of Film Art) technology allows fashionable and unique pictorial designs to be printed on the spe- cially designed changeable LCD back covers. If your purchase option includes the specially designed change- able LCD back cover option, then follow the instructions in “Changing the Optional LCD Back Covers”...
Page 44 Quick Start Guide 1 - 20...
Page 45: Features & Components
Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • External USB Optical (CD/DVD) Device • Multi-In-1 Card Reader • TouchPad and Buttons/Mouse •...
Page 46: Hard Disk Drive
Features & Components Hard Disk Drive  The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other 2.5" serial (SATA) HDDs with a height of 9.5 mm. Before attempting to ac- If you want to upgrade your computer by replacing the existing hard disk with a fast- cess any of the internal...
Page 47: External Usb Optical (Cd/Dvd) Device
Features & Components External USB Optical (CD/DVD) Device  An external USB optical (CD/DVD) device is available as an option for this com- USB Cables puter. The optical device may be used as a boot device if properly set in the BIOS (see “Boot Menu”...
Page 48: Handling Cds Or Dvds
Features & Components Handling CDs or DVDs  Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.
Page 49: Dvd Regional Codes
Features & Components DVD Regional Codes Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD- ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Page 50: Multi-In-1 Card Reader
Features & Components Multi-In-1 Card Reader  The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Page 51: Touchpad And Buttons/Mouse
Features & Components TouchPad and Buttons/Mouse  The TouchPad is an alternative to the mouse; however, you can also add a mouse to TouchPad Scrolling your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. This computer model se- ries may feature different TouchPad versions.
Page 52: Finger Sensing Pad Configurator
Features & Components Finger Sensing Pad Configurator  The Finger Sensing Pad Configurator allows you to use a configure the settings for the Finger Pad device and software. The left pane in the control panel contains Mouse Driver all the configurable items, and you can click the “+” to expand the menu selections. If you are using an ex- ternal mouse your op- You can configure the settings from the Device Settings tab in Mouse Properties:...
Page 53: Gestures
Features & Components Gestures  Click Gestures and make sure that the Enable Gestures tickbox is clicked. Double- click Gestures and then double-click Advanced to open the submenu. You can con- Play Video figure any of the gestures from this submenu. You can get a clearer view of the gestures in- volved by clicking the...
Page 54: Audio Features
Features & Components Audio Features This computer will feature one of two possible audio systems depending on your purchase configuration. See the appropriate following pages for audio control panel information. 2 - 10 Audio Features...
Page 55: Via Hd Audio Deck
Features & Components VIA HD Audio Deck  You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Sound Volume Deck control panel Adjustment The sound volume level The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Page 56 Features & Components Expert Mode will allow you to access more advanced configuration menus. Figure 2 - 6 VIA HD Audio Deck (Expert Mode) 2 - 12 Audio Features...
Page 57: Realtek Hd Audio Manager
Features & Components Realtek HD Audio Manager  You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ Sound Volume control panel (right-click the taskbar icon to bring up an audio menu).
Page 58: Optimizing Audio Recording
Features & Components Optimizing Audio Recording Follow these instructions to optimize your audio recording. Double-click the taskbar icon to bring up the Realtek HD Audio Manager. Click the Microphone tab. Click the Noise Suppression button to prevent any background noise or feedback.
Page 59: Adding A Printer
Features & Components Adding a Printer  The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the print- er attach the parallel ca- USB Printer...
Page 60 Features & Components 2 - 16...
Page 61: Power Management
Power Management Chapter 3: Power Management  Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 62: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Page 63: Turning On The Computer
Power Management Turning On the Computer  Now you are ready to begin using your computer. To turn it on simply press the pow- Forced Off er button on the front panel. If the system “hangs”, When the computer is on, you can use the power button as a Stand by/Hibernate/ and the Ctrl + Alt + Del Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and key combination doesn’t...
Page 64: Power Plans
Power Management Power Plans  The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 65 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.
Page 66: Power-Saving States
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps.
Page 67: Hibernate
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost.
Page 68: Configuring The Power Buttons
Power Management Configuring the Power Buttons  The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Click Choose what the power buttons do on Protection the left menu in Power Options to bring up the menu.
Page 69: Resuming Operation
Power Management Resuming Operation  You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Closing the Lid If you have chosen to Power Status To Resume Icon Color...
Page 70: Energy Star Power Saving
Power Management Energy Star Power Saving  This system supports Energy Star power management features that place comput- ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period Taskbar Icon of inactivity. If you want to enable Energy Star power saving then follow these in- If the taskbar icon does structions: not appear then click the...
Page 71: Battery Information
Power Management Battery Information  Follow these simple guidelines to get the best use out of your battery. Low Battery Battery Power Warning Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- grams you are running, and peripheral devices attached.
Page 72: Conserving Battery Power
Power Management Conserving Battery Power  • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Wireless Hot Keys • Lower the brightness level of the LCD display. The system will decrease LCD The computer’s wireless brightness slightly to save power when it is not powered by the AC/DC adapter.
Page 73: Battery Life
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason (e.g.
Page 74: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack  • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode Caution • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly re- placed.
Page 75: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 76 Power Management Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. Figure 3 - 9 Change Plan Settings / Change Advanced Power Settings 3 - 16 Battery Information...
Page 77 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 10 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 78 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 79: Drivers & Utilities (Win7)
Drivers & Utilities (WIN7) Chapter 4: Drivers & Utilities (WIN7) What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some You will need to attach an optical device drive to the of the computer’s subsystems.
Page 80: Driver Installation (Win7)
Drivers & Utilities (WIN7) Driver Installation (WIN7) Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc into an attached optical drive and click Install Drivers Installer menu below.
Page 81 Drivers & Utilities (WIN7) Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Install- Driver - Windows 7 Page # er application and browse to the executable file in the Chipset Page 4 - 5 appropriate driver folder. Video (VGA) Page 4 - 5 Windows Update Page 4 - 5...
Page 82: Updating/Reinstalling Individual Drivers
Drivers & Utilities (WIN7) Updating/Reinstalling Individual Drivers User Account Control If you wish to update/reinstall individual drivers it If a User Account Control prompt appears as part of may be necessary to uninstall the original driver.To do the driver installation procedure, click Continue or this go to the Control Panel in the Windows OS and Allow, and follow the installation procedure as direct- double-click the Programs and Features icon (Pro-...
Page 83: New Hardware Found
Drivers & Utilities (WIN7) New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” dur- Insert the Device Drivers & Utilities + User’s Manual ing the installation procedure (other than when out- disc into your attached CD/DVD drive and click In- lined in the driver install procedure), click Cancel stall Drivers (button).
Page 84: Card Reader
Drivers & Utilities (WIN7) Card Reader Audio 1. Click 4.Install Cardreader Driver > Yes. 1. Click 7.Install Audio Driver > Yes. 2. Click Install > Finish to complete the installa- 2. Click Next. tion. 3. Click the button to agree to the license and click Next.
Page 85: Windows Experience Index
Drivers & Utilities (WIN7) Windows Experience Index After the drivers are installed follow this procedure to  ensure an accurate rating from the Windows Experi- Windows 7 Update ence Index: After installing all the drivers make sure you enable Win- dows Update in order to get all the latest security up- 1.
Page 86: Optional Drivers
Drivers & Utilities (WIN7) Optional Drivers Wireless LAN Module See the pages indicated overleaf for the driver installa- See the introduction in “Wireless LAN Module” on tion procedures for any modules included in your pur- page 7 - 2, and check the installation procedure. chase option.
Page 87: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities  Overview BIOS Screens Note that BIOS This chapter gives a brief introduction to the computer’s built-in software: screens pictured these pages are intend- Diagnostics: The POST (Power-On Self Test) ed for guidance in set- ting up your system’s BIOS.
Page 88: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST)  Each time you turn on the computer, the system takes a few seconds to conduct a POST Screen POST, including a quick test of the on-board RAM (memory). 1.BIOS information As the POST proceeds, the computer will tell you if there is anything wrong. If there 2.CPU type is a problem that prevents the system from booting, it will display a system summary 3.Memory status...
Page 89: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 90: The Setup Utility
BIOS Utilities The Setup Utility  The Phoenix SecureCore Setup Utility tells the system how to configure itself and BIOS Settings manage basic features and subsystems (e.g. port configuration). Warning Entering Setup Incorrect settings can cause your system to To enter Setup, turn on the computer and press F2 during the POST. The prompt malfunction.
Page 91: Setup Screens
BIOS Utilities Setup Screens  The following pages contain additional advice on portions of the Phoenix Se- cureCore Setup Utility. Setup Menus Setup menus Along the top of the screen is a menu bar with menu headings. When you select a shown in this section are heading, a new screen appears.
Page 92: Main Menu
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings.
Page 93: Sata Port 1 (Main Menu)
BIOS Utilities SATA Port 1 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a HDD on the com- puter’s Serial ATA Port 1. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable.
Page 94: Advanced Menu
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu  SATA Mode Selection If you have installed the Windows 7 operating system with AHCI mode enabled (default setting), DO NOT disable AHCI mode (if you wish to dis- able AHCI mode you will need to reinstall the Win- dows 7 OS).
Page 95: Sata Mode Selection (Advanced Menu)
BIOS Utilities SATA Mode Selection (Advanced Menu) You can configure SATA (Serial ATA) control to operate in either IDE (native/ compatible) or AHCI (Advanced Host Controller Interface) modes from this menu. The SATA mode should be set to AHCI mode for this system (unless you are sure your hard disk can only operate in IDE mode or you are using the Windows XP OS).
Page 96: Security Menu
BIOS Utilities Security Menu  Security Menu changes make here affect the access to the Setup utility itself, and also access to your ma- chine as it boots up af- ter you turn it on. These settings do not affect your machine or network passwords which will be set in...
Page 97: Set User Password (Security Menu)
BIOS Utilities Set User Password (Security Menu)  You can set a password for user mode access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless Password Warning you choose to set a Password on Boot (see below). Many menu items in the Phoenix If you set a boot pass- SecureCore Setup Utility cannot be modified in user mode.
Page 98: Boot Menu
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu  BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- When you turn the computer on it will look for an operating system (e.g. Windows ject to constant change 7) from the devices listed in this menu, and in this priority order.
Page 99: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Set- up defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Page 100 BIOS Utilities 5 - 14...
Page 101: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview  This chapter contains information on upgrading the computer. Follow the steps out- lined to make the desired upgrades. If you have any trouble or problems you can con- Warranty Warning tact your service representative for further help.
Page 102: When Not To Upgrade
Upgrading The Computer When Not to Upgrade  These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake upgrade proce- • Your system is still under warranty or a service contract dures, make sure that •...
Page 103: Removing The Battery
Upgrading The Computer Removing the Battery  If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Turn the computer off, and turn it over. Please check with your Slide the latch in the direction of the arrow.
Page 104: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has one memory socket for 204 pin Small Outline Dual In-line (SO- DIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 2 details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 105 Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & Figure 6 - Figure 6 - 3 RAM Module Release Latches  Contact Warning Be careful not to touch the metal pins on the module’s connecting...
Page 106 Upgrading The Computer Insert a new module holding it at about a 30° angle and fit the connectors firmly  into the memory slot. The module’s pin alignment will allow it to only fit one way. Make sure the module Cover Pins is seated as far into the slot as it will go.
Page 107: Changing The Optional Lcd Back Covers
Upgrading The Computer Changing the Optional LCD Back Covers  If your purchase option includes the specially designed changeable LCD back cover Rubber Screw option (not available for all models), then follow the instructions below to change Covers the covers (note these covers are not applicable to all models in this series - consult your service center for details).
Page 108 Upgrading The Computer Carefully slide the cover forward in the direction of the arrows & illustrated below Figure 6 - 7 Slide the Cover Forward Remove the LCD back cover Figure 6 - 8 Remove the LCD Back Cover 6 - 8 Changing the Optional LCD Back Covers...
Page 109 Upgrading The Computer Align the replacement cover with the dotted line as illustrated below (and as marked on the cover). Figure 6 - 9 Replacing the LCD Back Cover Slide the cover forward until it clicks firmly into place Run your hands around the sides and front of the cover to make sure it is firmly aligned in place (carefully press down to make sure the fit is secure).
Page 110: Upgrading The Hard Disk
Upgrading The Computer Upgrading the Hard Disk  If you want to upgrade your computer by replacing the existing hard disk with a fast- Warranty er/new one you will need to contact your customer service representative. We rec- ommend that you do not do this yourself, since if it is done incorrectly you may The CPU is not a user damage the computer and may violate your warranty.
Page 111: Modules & Options
Modules & Options Chapter 7: Modules & Options  Overview Driver Installation & Module Power This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please Make sure any modules (e.g.
Page 112: Wireless Lan Module
Modules & Options Wireless LAN Module  If you have included an 802.11b/g/n WLAN module in your purchase option, make Wireless Device sure that the Wireless LAN module is on before installing the driver (the WLAN Operation Aboard module’s default power state is off). Aircraft Use the Fn + F11 key combination (see “Function/Hot Key Indicators”...
Page 113: 802.11B/G/N Wlan Driver Installation
Modules & Options 802.11b/g/n WLAN Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Insert the Device Drivers & Utilities + User’s Manual disc into your exter- nal optical device drive. 2. Click Option Drivers (button). 3.
Page 114: Connecting To A Wireless Network
Modules & Options Connecting to a Wireless Network  Make sure the Wireless LAN module is turned on. Network and Click the taskbar wireless icon , and then double-click an access point to con- Sharing Center nect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing You can also use the Net- setting changes, and creating a new network).
Page 115 Modules & Options You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Page 116 Modules & Options Click the taskbar icon to see any currently connected networks.  To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). Security Enabled Networks You should try to make sure that any network you are connecting to is a se- cure network.
Page 117: Windows Mobility Center
Modules & Options Windows Mobility Center  The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Wireless Hot Keys To access the Windows Mobility Center: The computer’s wireless function keys will not func- Click Start, and click Control Panel (or point to Settings and click Control...
Page 118: Pc Camera Module
Modules & Options PC Camera Module  The PC Camera application captures video files and takes pictures. Before installing Latest PC Camera the driver, make sure that the optional PC Camera is on. Use the Fn + F10 key com- Driver Information bination (see “Function/Hot Key Indicators”...
Page 119: Pc Camera Driver Installation
Modules & Options PC Camera Driver Installation  1. Insert the Device Drivers & Utilities + User’s Manual disc into your exter- nal optical device drive. PC Camera Screen 2. Use the Fn + F10 key combination to turn the camera module on and give the Refresh system a few seconds to recognize the camera module before beginning the The PC Camera module...
Page 120 Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 121 Modules & Options Camera Application  The camera application is a video viewer for general purpose video viewing and test- ing, and for capturing video files to .avi format. Pre-Allocating File Size/Space Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see “Set Capture File”...
Page 122 Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 123 Modules & Options Eliminating Screen Flicker  If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. Latest PC Camera Driver Information Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter..
Page 124 Modules & Options Zoom The camera program allows you to zoom the camera in and out. Run the camera application from the desktop shortcut. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 6 Zoom/Setting Taking Still Pictures ...
Page 125: G/Hspa Module
Modules & Options 3.75G/HSPA Module  If you have included an optional 3.75G/HSPA (High Speed Packet Access) module in your purchase option, you will have the appropriate application (Mobile Partner 3.75G/HSPA Module Options or BandLuxe HSDPA Utility) provided for your particular module. Follow the in- structions on page 1 - 14 to install the USIM card (supplied by your service provid-...
Page 126 Modules & Options Before installing the application, make sure that the 3.75G/HSPA module is ON  (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function/Hot 3.75G/HSPA Key Indicators”...
Page 127: Mobile Partner
Modules & Options Mobile Partner  With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Mobile Partner application. The Mobile Partner Wireless Device application allows you to directly access your HSPA internet service from the com- Operation Aboard puter.
Page 128: Mobile Partner Application
Modules & Options Mobile Partner Application  You will need to contact your service provider to obtain the exact details of how ex- actly to configure the settings on this page. Mobile Partner Help Profile Management To get help on Mobile Partner configuration Power on the 3.75G/HSPA module using the Fn +...
Page 129 Modules & Options Connecting to the Service Provider Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop The software will run and you can select the Profile Name from the menu.
Page 130 Modules & Options When the connection is successful you can move the cursor over the network icon in the taskbar to display the connection information. Figure 7 - 10 Connected Taskbar Notification You can then access the internet, download e-mail etc. as per any internet connection.
Page 131 Modules & Options To disconnect click the Disconnect icon, or right click the taskbar icon and select Disconnect. Figure 7 - 11 Disconnect 10. The program will disconnect from the service provider. 11. The module will still be on, and you will need to press the Fn + combination to turn it off.
Page 132 Modules & Options 12. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection. Figure 7 - 12 Exit Prompt 13. Exiting the program terminates the connection, but DOES NOT turn off the 3.75G/ HSPA module, and you will need to press the Fn + key combination to turn off the module (pay careful attention to this aboard aircraft - see...
Page 133: Text Messaging Service
Modules & Options Text Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the Mobile Partner program, if your service supports SMS. Reading SMS Messages An icon will blink at the bottom of the Mobile Partner interface to notify you of any new messages received.
Page 134: Bandluxe Hsdpa Utility
Modules & Options BandLuxe HSDPA Utility  With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the BandLuxe HSDPA Utility. The BandLuxe HS- Wireless Device DPA Utility allows you to directly access your HSPA internet service from the com- Operation Aboard Aircraft puter.
Page 135: Bandluxe Hsdpa - Connection Manager
Modules & Options BandLuxe HSDPA - Connection Manager The connection information is stored on the USIM card supplied by the service pro- vider (where this is not the case you may need to create a profile - see “Creating a Profile”...
Page 136 Modules & Options The system will connect to your network (you may need to set your network connection to home, work or public on the first connection). The connected icon will appear at the top of the utility screen. Figure 7 - 14 Connected You can then access the internet, download e-mail etc.
Page 137 Modules & Options While you are connected the taskbar icon will display the connected icon , and the taskbar will display the connected icon Figure 7 - 16 Taskbar Icon (Connected) To disconnect from the service provider, click the Disconnect icon, or click the close icon at the top right of the utility, and click Yes to confirm.
Page 138: Creating A Profile
Modules & Options Creating a Profile Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu > Profile. Figure 7 - 17 Menu - Profile The default profile will display the service provider’s name from the USIM card.
Page 139 Modules & Options Click New (button) and input any Network Settings required by your service  provider (all fields may not need to be filled in). The profile name is used to identify your profile if a number of profiles are used. You will need to check with your service provider to confirm if the User Name and Password Password are required.
Page 140 Modules & Options Click the newly created profile in the profile window and then click Default (button)  to set the profile as the default connection (note that only one profile may be stored as the default connection). New SIM Card 10.
Page 141: Choosing A Profile
Modules & Options Choosing a Profile If you need to switch stored profiles follow the instructions below: Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu >...
Page 142: Editing A Profile
Modules & Options Editing a Profile  If you need to edit stored profiles follow the instructions below: Get the Latest Access the Connection Manager from the Start menu (Connection Manager Access Point Name ), or (Start > Programs/All Programs > BandLuxe > BandLuxe Database HSDPA Utility R11 >...
Page 143: Text Messaging Service (Sms)
Modules & Options Text Messaging Service (SMS)  In addition to standard internet services you may also send and receive SMS text messages using the Connection Manager, if your service supports SMS. Incoming Messages Inbox If the program is open The Inbox will contain any received SMS.
Page 144 Modules & Options Sent  The Sent folder contains any successfully sent SMS. Select the message and press the Delete to erase the record. Contact List Types Outbox Select a contact The Outbox folder contains any completed but unsent SMS. Select the message and from the SIM card.
Page 145 Modules & Options Template A template can store text that is used regularly in messages, and can be easily insert- ed in to any new SMS. Click Template (button) to view any stored templates. Click to highlight a template and click Select (button) to insert it into the message. Click New (button) to create a new template, and Save (button) to add it to the existing list.
Page 146: Setting
Modules & Options Setting  The Setting menu allows you to edit the programs basic parameters. Access the Connection Manager from the Start menu (Connection Manager Language ), or (Start > Programs/All Programs > BandLuxe > BandLuxe The Connection Manager HSDPA Utility R11 >...
Page 147 Modules & Options SMS - Preference Click the New SMS Notify checkbox to be automatically notified when a new SMS arrives. If enabled a the incoming message notification will appear in the taskbar, Figure 7 - 27 Incoming SMS Notification and an envelope icon will appear in the upper left corner of the Home screen when a new message arrives.
Page 148 Modules & Options This menu allows you to edit the USIM card Personal Identification Number (PIN) and Enable/Disable the PIN if necessary. Press Apply after making any changes. A SIM card must be inserted for this function to be activated. Figure 7 - 29 Setting - SIM If a PIN code is enabled, the input will be requested during USIM card initialization.
Page 149 Modules & Options Radio Set the appropriate network search options from the dual mode setting menu. Click Apply (button) after making any changes. Figure 7 - 30 Setting - Radio Note: 2G/3G/3.5G data transferring will be disconnected when you apply a new Ra- dio setting.
Page 150 Modules & Options Network - Network Selection  Edit the network selection settings from this menu. The Standard (auto) setting will search for networks in the order specified in the Prefer list. Click Standard (auto) Network Setting > Next to view and adjust the Prefer list. The Prefer list is displayed at the top of the Note that the network set- screen, and the bottom of the screen lists all available networks.
Page 151 Modules & Options The Manual setting allows you to choose a network from all available. Click Man- ual > Next to view the list. Click to highlight a network from the list, and click Se- lect (button) to choose the network, or Cancel (button) to make no change. Figure 7 - 32 Setting - Network Manual...
Page 152: Statistics & Information
Modules & Options Statistics & Information The Statistics screen displays a graph of recent upload and download activity. No data will be displayed if there is no current connection. Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 >...
Page 153: Bluetooth Module
Modules & Options Bluetooth Module  There are two Bluetooth module options available for this computer. If your pur- Wireless Device chase option (Model D only) includes the Combination Wireless LAN & V3.0 Operation Aboard Bluetooth module then install the driver as instructed overleaf. Follow the instruc- Aircraft tions on page 7 - 49...
Page 154: Bluetooth Combo Driver Installation
Modules & Options Bluetooth Combo Driver Installation  Note this driver is required only for the combo Bluetooth and WLAN module only. High Speed Bluetooth 1. Before installing the driver make sure the Bluetooth module is powered Data Transfer on (use Fn + F12 key combinations), then insert the Device Drivers & Util- The Combination Wire- ities + User’s Manual disc into the CD/DVD drive.
Page 155: Bluetooth & Wlan Combo Settings
Modules & Options Bluetooth & WLAN Combo Settings This information applies to the combo Bluetooth and WLAN module only. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu).
Page 156 Modules & Options Click General Settings to change the computer name that other Bluetooth  devices will see, and click the tickbox to Allow Bluetooth devices to find this computer. High Speed Mode Click OK to confirm the settings. Support Make sure that Enable high speed mode sup- port in General Settings...
Page 157 Modules & Options Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings. Figure 7 - 36 File Transfer Settings Bluetooth Module 7 - 47...
Page 158: Bluetooth Networking Setup
Modules & Options Bluetooth Networking Setup This information applies to the combo Bluetooth and WLAN module only. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 34 on page 7 - 45).
Page 159: Bluetooth & Wlan Combo Module Configuration
Modules & Options Bluetooth & WLAN Combo Module Configuration Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On Press the Fn + F12 key combination to power on the Bluetooth module.
Page 160 Modules & Options You will then be presented with a menu of options to select from. Figure 7 - 39 Bluetooth Device Options Click the appropriate button to connect to the device. 7 - 50 Bluetooth Module...
Page 161 Modules & Options You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.
Page 162: Bluetooth Configuration In Windows 7
Modules & Options Bluetooth Configuration in Windows 7  Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Add a Device Make the device discoverable (to do this check your device documentation). Click Start, and click To Turn the Bluetooth Module On Control Panel and then...
Page 163 Modules & Options To Add a Bluetooth Device  Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been pre- viously connected then the pairing option menu will appear when you at- tempt subsequent con-...
Page 164 Modules & Options Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing.  Figure 7 - 43 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection proce- dure, and may require you to confirm a pairing code is correct on both devices.
Page 165 Modules & Options To Change Settings for the Bluetooth Device  Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click Bluetooth, type a new name and click OK). •...
Page 166 Modules & Options 7 - 56...
Page 167: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 168: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 169: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 170: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 171: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 172 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Page 173: Problems And Possible Solutions
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the work. battery is present and seated properly (the design of the battery only allows it to go in one way).
Page 174 Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 175 Troubleshooting Problem Possible Cause - Solution No image appears on the external You haven’t installed the video driver and configured it appropriately from the monitor I have plugged in and powered Control Panel. See “Display Devices & Options” on page B - 5/“Display & Graphics Properties”...
Page 176 Troubleshooting Problem Possible Cause - Solution Unwelcome numbers appear when Check that Num Lock is not turned ON. typing.  Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.
Page 177 Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be The module is off. Press the Fn + F10 key combination in order to enable the detected. module (see “Function/Hot Key Indicators” on page 1 - 9/“Function/Hot Key Indicators” on page D - 4).
Page 178 Troubleshooting Problem Possible Cause - Solution I am sliding my finger up and down on the There are different TouchPad versions available on this computer, and this right side of the TouchPad to scroll a version requires tapping/holding to scroll. Either tap repeatedly, or hold the Window and the TouchPad does not finger down, at the top or bottom right of the touchpad (depending on the respond.
Page 179: Bluetooth Connection Problems
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Win- dows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.
Page 180 Troubleshooting Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... Select Bluetooth Radios from the list.
Page 181 Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list).
Page 182 Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices. Figure 8 - 5 - Device Manager - Bluetooth Radio 8 - 16 Bluetooth Connection Problems...
Page 183: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 184: Notebook Ports And Jacks
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
Page 185 Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Page 186 Interface (Ports & Jacks) A - 4...
Page 187: Intel Video Driver Controls
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on  page 1 - DVMT Notes Intel Video Driver Installation DVMT is not local video memory. Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - Video DVMT is not user-con-...
Page 188: Intel Gma Driver For Mobile
Intel Video Driver Controls Intel GMA Driver for Mobile  Advanced video configuration options are provided by the Intel(R) Graphics Me- Taskbar Icon dia Accelerator Driver for Mobile. To access the Intel(R) Graphics Media Accel- erator Driver for mobile control panel: You can also access the controller properties...
Page 189 Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking  the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?”...
Page 190: Scheme Options
Intel Video Driver Controls Scheme Options  Use Scheme Options to configure quick settings for applications which require spe- cific resolution and color settings in order to run properly e.g. games, multimedia Application.exe programs. To set the scheme options: You will need to locate Go to the GMA for mobile control panel (see page the actual application executable (.exe) file,...
Page 191: Display Devices & Options
Intel Video Driver Controls Display Devices & Options  Besides the built-in LCD, you can also use an external VGA monitor (CRT) or ex- ternal Flat Panel Display as your display device. A VGA monitor/Flat Panel Dis- Function Key Combination play connects to the external monitor port.
Page 192: Attaching Other Displays
Intel Video Driver Controls Attaching Other Displays  If you prefer to use a monitor or flat panel display, connect it to the external monitor Multiple Display port on the left of the computer. At least one other dis- To Enable Intel(R) Dual Display Clone Mode play must be attached in Attach your external display to the external monitor port, and turn it on.
Page 193 Intel Video Driver Controls To Enable Extended Desktop Mode:  Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Display Settings Devices. Extended Desktop Click to choose Extended Desktop (Operating Mode).
Page 194 Intel Video Driver Controls Attaching Other Displays  Configuring an External Display in Windows 7 Function Key Attach your external display to the external monitor port and turn it on. Combination Go to the Screen resolution control panel. Click the Detect button. You can use the Fn + The computer will then detect any attached displays.
Page 195 Intel Video Driver Controls You can configure the displays from the Multiple Displays menu. Figure B - 7 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) •...
Page 196 Intel Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configura- tion and modes (this is particularly useful when attaching a projector) in Windows 7. Attach your external display to the external monitor port and turn it on.
Page 197: Specifications
Specifications Appendix C: Specifications  Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for details.
Page 198: Processor
Specifications Processor Display Video Adapter Intel® Atom® Processor N455 Models A & B: Intel® GMA 3150 Integrated Video 1.66 GHz, 512K On-die L2 Cache & 10.1” (25.6cm) WSVGA (1024 * 600) Intel® Dynamic Video Memory 667MHz FSB, TDP 6.5W - BGA 16:9 TFT LED Backlit Panel (3.6mm Technology Supporting Shared Memory Package, 45nm (45 Nanometer) Process...
Page 199: Audio
Specifications Audio Communication Card Reader High Definition Audio Compliant Interface 10Mb/100Mb Base-TX Ethernet LAN Embedded Multi-In-1 Card Reader 2 * Built-In Speakers - MMC/ RS MMC 802.11b/g/n Wireless LAN Half Mini-Card Built-In Microphone - SD/ Mini SD / SDHC Module (Factory Option) - MS/ MS Pro/ MS Duo Pointing Device UMTS/HSPDA-based 3.75G/HSPA (Half...
Page 200: Power Management
Specifications Power Management Environmental Spec Wake On LAN Temperature ° ° Wake On USB (Windows 7 Only) Operating: C - 35 Energy Star 5.0 Compliant Non-Operating: -20°C - 60°C Relative Humidity Power Operating: 20% - 80% Non-Operating: 10% - 90% Full Range AC/DC Adapter AC Input: 100 - 240V, 50 - 60Hz Dimensions &...
Page 201: Windows Xp Information
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS. D - 1...
Page 202: Windows Xp Start Menu & Control Panel
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 203: Touchpad And Buttons/Mouse
Windows XP Information TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad”...
Page 204: D - 4 Function/Hot Key Indicators
Windows XP Information Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Keys Function Keys Function Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle 3.75G Module Power Brightness Decrease/...
Page 205: Audio Features
Windows XP Information Audio Features This computer will feature one of two possible audio systems depending on your purchase configuration. See the appropriate following pages for audio control panel information. Audio Features D - 5...
Page 206: Via Hd Audio Deck
Windows XP Information VIA HD Audio Deck You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel The volume may also be adjusted by means of the Fn + F5/F6 key combination. ...
Page 207: Realtek Hd Audio Manager
Windows XP Information Realtek HD Audio Manager You can configure the audio options on your computer from the Sounds and Audio Devices Windows con- trol panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus).
Page 208: Video Features
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. To access Display Properties in Windows: Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category.
Page 209: Display & Graphics Properties
Windows XP Information Display & Graphics Properties  Taskbar Icon You can also access the controller prop- erties from the taskbar. Click on the icon to bring up the menu and scroll to Graphics Properties. If you cannot see the tray icon go to the Intel(R) Graphics Media Accelerator Driver for Mobile tab and click the “Show Tray Icon”...
Page 210 Windows XP Information You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button.  Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: •...
Page 211: Display Devices & Options
Windows XP Information Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port. The following display modes are available.
Page 212: D - 12 Attaching Other Displays
Windows XP Information Attaching Other Displays  If you prefer to use a monitor or flat panel display, connect it to the external monitor Display Selection port on the left of the computer. At least one other dis- 1. Attach your external display to the external monitor port, and turn it on. play must be attached in 2.
Page 213 Windows XP Information To Enable Intel(R) Dual Display Clone (Intel GMA) Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Click to choose Intel(R) Dual Display Clone (Operating Mode). Click Apply, and OK to confirm the settings change.
Page 214 Windows XP Information To Enable Extended Desktop (Intel GMA) Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Click to choose Extended Desktop (Operating Mode). Click Apply, and OK to confirm the settings change.
Page 215 Windows XP Information To Enable Extended Desktop (Windows Display Properties) Attach your external monitor to the external monitor port, and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes).
Page 216: Power Management Features
Windows XP Information Power Management Features  To conserve power, especially when using the battery, your computer uses the ACPI OS Note power management system. Power management conserves power by controlling in- dividual components of the computer (the monitor and hard disk drive) or the whole Power management functions...
Page 217: The Power Sources
Windows XP Information The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components.
Page 218: Turning On The Computer
Windows XP Information Turning on the Computer  Now you are ready to begin using your computer. To turn it on simply press the pow- Shutdown er button on the front panel. Note that you should al- When the computer is on, you can use the power button as a Stand by/Hibernate/ ways shut your comput- er down by choosing the Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and...
Page 219: Power Schemes
Windows XP Information Power Schemes  You can set your computer to conserve power through individual components by Resuming means of Power Schemes. You can also adjust the settings for each scheme to set Operation the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if Press a key on the key- the system reads or writes data, the hard disk motor will be turned back on).
Page 220 Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save pow- er. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Page 221: System Power Options
Windows XP Information System Power Options  You can use the system power options to stop the computer’s operation and restart Stand by/Hibernate where you left off. This system features Stand by and Hibernate sleep mode levels or Shutdown Error (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate”...
Page 222: Stand By
Windows XP Information Stand by  Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle System Resume at its slowest speed.
Page 223: Configuring The Power Button
Windows XP Information Configuring the Power Button  The power button may be set to send the computer in to either Stand by or Hiber- Sleep Button nate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter).
Page 224: D - 24 Battery Information
Windows XP Information Battery Information  Please follow these simple guidelines to get the best use out of your battery. Low Battery New Battery Warning Always completely discharge, then fully charge, a new battery (see “Battery FAQ” When the battery is criti- on page D - 27 for instructions on how to do this).
Page 225: Recharging The Battery With The Ac/Dc Adapter
Windows XP Information Battery life may be shortened through improper maintenance. To optimize the life and improve its perfor- mance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, “Removing the Battery”...
Page 226: Proper Handling Of The Battery Pack
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other ...
Page 227: Battery Faq
Windows XP Information Battery FAQ  How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t Caution turn off the computer by yourself even when you see a message that indicates the bat- Danger of explosion if tery is critically low, just let the computer use up all of the battery power and shut battery is incorrectly re-...
Page 228 Windows XP Information Driver Installation (WINXP) Check the driver installation order from Table D - 3 (the drivers must be installed in this order) Insert the Device Drivers & Utilities + User’s Manual which is the same as that listed in the Drivers Disc, click Install Drivers/Option Drivers (button) and Installer menu below.
Page 229: Driver Installation (Winxp
Windows XP Information Updating/Reinstalling Individual Drivers WinXP SP3 Driver Page # If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go Chipset Page D - 30 to the Control Panel in the Windows OS and double- click the Add/Remove Programs item.
Page 230: New Hardware Found
Windows XP Information New Hardware Found  If you see the message “New Hardware Found” dur- ing the installation procedure (other than when out- Windows XP Service Pack 3 lined in the driver install procedure), click Cancel Make sure you install Windows XP Service Pack 3 (or a to close the window, and follow the installation proce- Windows XP version which includes Service Pack 3) be- dure.
Page 231: Lan
Windows XP Information Hot Key 1. Click 3.Install LAN Driver > Yes. 1. Click 6.Install HotKey AP > Yes. 2. Click Install > Finish to complete the installa- 2. Click Next > Install. tion. 3. Click Finish > Finish to restart the computer. 3.
Page 232: Module Drivers
Windows XP Information Module Drivers Make sure any modules (e.g. WLAN, PC Camera, 3.75G/HSPA or Bluetooth) are ON before installing See the following pages for the driver installation pro- the appropriate driver. cedures for any of the optional modules included in your purchase configuration.
Page 233 Windows XP Information Wireless LAN, Bluetooth & 3.75G Modules  Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Page 234: D - 34 Wireless Lan Module
Windows XP Information Wireless LAN Module  If you have included an 802.11b/g/n WLAN module in your purchase option, make Wireless Device sure that the Wireless LAN module is on before installing the driver (the WLAN Operation Aboard module’s default power state is off). Aircraft The use of any portable Use the Fn + F11 key combination (see...
Page 235: 802.11B/G/N Wlan Driver Installation
Windows XP Information 802.11b/g/n WLAN Driver Installation  1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. Network 2. Click Option Drivers (button). Connection 3. Click 1.Install WLAN Driver > Yes. Use the Windows Net- 4.
Page 236 Windows XP Information PC Camera Module  Before installing the optional PC Camera module driver use the Fn + F10 key com- Taking Still Pictures bination to toggle power to the module. There are a number of different camera mod- ules available with this computer model series.
Page 237: Pc Camera Driver Installation
Windows XP Information PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into your external optical device drive. 2. Use the Fn + F10 key combination to turn the camera module on and give the system a few seconds to rec- ognize the camera module before beginning the installation process.
Page 238: 3.75G/Hspa Module
Windows XP Information 3.75G/HSPA Module  If you have included an optional 3.75G/HSPA (High Speed Packet Access) module 3.75G/HSPA in your purchase option, you will have the appropriate application provided for your Modules & System particular module. Follow the instructions on page 1 - 14 to install the USIM card Wake Up...
Page 239 Windows XP Information Mobile Partner Application Installation 1. Enable power to the module by pressing the Fn + key combination (give the module about 10 sec- onds to power on - the on screen icon will indicate the module’s power status). 2.
Page 240: Bandluxe Hsdpa Utility Installation
Windows XP Information BandLuxe HSDPA Utility Installation 1. Enable power to the module by pressing the Fn + key combination (give the module about 10 sec- onds to power on - the on screen icon will indicate the module’s power status). 2.
Page 241: Bluetooth Module
Windows XP Information Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver. Use the Fn + F12 key combination (see “Function/Hot Key Indi- cators”...
Page 242: Standard Bluetooth Configuration In Windows Xp
Windows XP Information Standard Bluetooth Configuration in Windows XP  If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: Wireless Device Operation Aboard 1. Access the Network Connections control panel in Windows (Start > Settings > Aircraft Network Connections OR Start >...
Page 243 Windows XP Information Setup your Bluetooth Device so the Computer Can Find it  Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Bluetooth Taskbar To Turn the Bluetooth Module On Icon Press the Fn + F12 key combination to power on the Bluetooth module.
Page 244: To Add A Bluetooth Device
Windows XP Information To Add a Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. 3. Click Devices (tab), and then click Add. 4.
Page 245 Windows XP Information To Change Settings for the Bluetooth Device Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • Change the name of the device (click General, type a new name and click OK). •...
Page 246 Windows XP Information D - 46...

Clevo M1110Q User Manual

Quick Start Guide

Features & Components

Power Management

Drivers & Utilities (WIN7)

BIOS Utilities

Upgrading the Computer

Modules & Options

Troubleshooting

Interface (Ports & Jacks)

Intel Video Driver Controls

Specifications

Windows XP Information

Quick Links

Need help?

Questions and answers

Related Manuals for Clevo M1110Q

Summary of Contents for Clevo M1110Q