Related Manuals for Phonic Ear OnWave
Summary of Contents for Phonic Ear OnWave
- Page 1 direct digital synthesis FM u s e r g u i d e P E 560T transmitter P E 500R receiver P E 506R receiver specs available on-line at www.phonicear.com...
-
Page 2: Table Of Contents
Large Area Antenna........6 OnWave System Setup and Operation Understanding hearing assistance . -
Page 3: Transmitter: Pe 560T
10kHz for a wider frequency response handed thread). US models are required and fuller sound. by the FCC to feature connectors unique to Phonic Ear to prevent the use of non- line/mic regulation antennas. Contact your Press to select line or mic input (see 4b Phonic Ear dealer. - Page 4 transmitter: PE 560T (cont’d) front back...
-
Page 5: Wide-Band Receiver: Pe 500R
(2 hours remaining battery life); lights brighter back when charging tuning screw Multi-turn screw for setting the Phonic Ear PE 500R receiver frequency. Wide Band Receiver Pre-tuned to 72.9 MHz 99 014737 (channel E). (see 8b on page 13 ) -
Page 6: Narrow-Band Receiver: Pe 506R
(see 8C ) back 31 frequency code label (inside) Identifies the frequency code for Phonic Ear PE 506R each of the six available channels Narrow-Band Receiver 99 014737 — — 72 MHz + mid band... -
Page 7: Ground Plane
ground plane (note that connectors have left-handed thread) 16 antenna jack Attach antenna here 17 cable jack Attach cable here 18 mounting holes Use screws to mount on a wall or, preferably, a ceiling; may also be placed on a tabletop... -
Page 8: Large Area Antenna
large area antenna 19 tuning ring Do not deform or move this ring, or you may affect the antenna's tuning and efficiency 20 worm clamps Loosen both clamps; extend the large center section to the black ring; tighten lower clamp; extend the smaller element to the black ring;... -
Page 9: Onwave System Setup And Operation
OnWave system setup and operation understanding hearing assistance without the OnWave system • distance • noise • echo with the OnWave system • distance • noise • echo direct-mount a standard antenna Attach antenna to back AT0777 of transmitter PE 560T Check RF Fault indicator. -
Page 10: Remote-Mount A Standard Antenna
OnWave system setup and operation (cont’d) remote-mount a standard antenna optimizes transmitter/antenna position PE 560T ground plane with cable (AT0776) ground plane with connector kit AT0775 (AT0775) AT0776 then PE 560T remote-mount a large-area antenna optimizes transmitter/antenna position PE 560T AT0773 Channels A–... -
Page 11: Mount The Transmitter In Rack Or Place On Top Of Rack
OnWave system setup and operation (cont’d) mount the transmitter in rack (requires remote mounting antenna) or place on top of rack AT0757 Plug transformer into AT0780/ OnWave power input AT0781 Plug transformer into wall socket connect line input Select Line-in... -
Page 12: Connect Microphone Input
OnWave system setup and operation (cont’d) connect microphone input Plug in microphone PE 560T XLR input then Select Mic-in activate phantom power (for electret condenser mics only † ) Press function Press line/mic Repeat steps to deactivate phantom power †Use phantom power only with condenser microphones. -
Page 13: Adjust Output Levels (With Adjustable Volume)
OnWave system setup and operation (cont’d) adjust output levels (if your house system has adjustable volume) Turn on and play house system test signal Increase sound system volume until..overload indicator lights Slowly decrease sound system volume until..overload indicator... -
Page 14: Music Or Speech
OnWave system setup and operation (cont’d) music or speech? (set for typical signal content) set bass cut (optimize for listeners or to reduce low-freq noise) Recommended Standard Setting Speech: 160Hz Music: 40Hz Recommended Noise Reduction Setting (air conditioning, low frequency hum) -
Page 15: Set Transmitter Band & Channel
OnWave system setup and operation (cont’d) set transmitter band & channel (optional; must tune your receiver to match!) Press function Press channel to select wide-band for 500R (channels indicated by letters) or narrow-band for 506R (channels indicated by numbers) then... -
Page 16: Set Pe 506R Channel
OnWave system setup and operation (cont’d) set PE 506R channel (must match your transmitter!) Find channel that matches transmitter Phonic Ear PE 506R Narrow-Band Receiver 99 014737 frequency – – 72 MHz + Set channel then (Users can switch to... -
Page 17: Lock/Unlock Your Settings
OnWave system setup and operation (cont’d) lock/unlock your settings Press function Press level - to lock Press function Press level + to unlock save settings Press power to turn unit saves settings in temporary memory off and save settings Press function... -
Page 18: Receiver Batteries
OnWave system setup and operation (cont’d) receiver batteries Light flashes when batteries are low 2 hours of battery life remain (4 hours with alkaline battery) warning! Do not stand charger case on bottom when charging. Damage Place charger case on its side when to charger may occur. -
Page 19: How To Use The Body-Worn Receiver
OnWave system setup and operation (cont’d) how to use the body-worn receiver AT0489 wire clip AT0737 pouch AT0076 lavalier cord then then On/Volume (verify power light is on) Switch to channel/ program (PE 506R only) -
Page 20: Warranty
To ensure that your batteries are as fresh as possible 6. Batteries if applicable upon arrival, we have intentionally not installed Phonic Ear Inc. reserves the right to make changes in them in your equipment. the design or construction of any of its instruments at... -
Page 21: Troubleshooting
troubleshooting no sound • If using the 500R, verify the receiver is tuned correctly (see user instructions section 8b ) • If using the 506R, verify the channel selected on the receiver matches the channel selected on the transmitter (see user instructions section 8c ) •... - Page 22 800.227.0735, then press 5 • canada: 800.263.8700 outside u.s./canada: Call your local Phonic Ear dealer • website: www.phonicear.com © 2003 Phonic Ear Inc. Phonic Ear and the names of Phonic Ear products are trademarks or registered 821-7289-102/rev. E/3839 903...
Need help?
Do you have a question about the OnWave and is the answer not in the manual?
Questions and answers