Summary of Contents for Open Sky DigiTECH 5000F
-
Page 1: User Manual
User Manual Free To Air / Multi CAS Embedded Digital Satellite Receiver DigiTECH 5000F... -
Page 2: Table Of Contents
Contents 1. SAFETY INFORMATION 2. FEATURES 3. CONNECTING YOUR RECEIVER 4. CONTROLS AND FUNCTIONS 4.1 REMOTE CONTROL UNIT 4.2 FRONT PANEL 4.2 REAR PANEL 5. MENU GUIDE 5.1 INSTALLATION 5.2 SYSTEM CONFIGURATION 5.3 CHANNEL ORGANIZATION 5.4 PARENTAL LOCK 5.5 RECEIVER INFORMATION 5.6 OTHER FUNCTION 5.7 COMMON INTERFACE 6. -
Page 3: Safety Information
. SAFETY INFORMATION . FEATURES MPEG-2 & Fully DVB Compliant Be sure to read this User’s Manual before starting the operation of the receiver. MPEG-2 Video (MP@ML), MPEG-1 Audio Layer1,Layer2 Do not open the cover. It is dangerous to touch the inside of the receiver due to PLL RF-Modulator UHF 21~69 with PAL B/G,I, D/K possible electric hazard. -
Page 4: Connecting Your Receiver
. CONNECTING YOUR RECEIVER There are several ways of connecting the receiver to your TV, VCR and / or Hi-Fi SYSTEM. Consult your local supplier for assistance in setting-up your system that is best suited to your requirements. 2) CONNECTING THE RECEIVER WITH DISH SYSTEM After installing your dish system, connect the coaxial cable from LNB of your dish antenna to “LNB IN”... -
Page 5: Controls And Functions
. CONTROLS AND FUNCTIONS 4. 1. REMOTE CONTROL UNIT 1) POWER : This is used to switch the receiver to ON/STANDBY mode. LAST 15) LAST : This key is used to return to the previous channel. 16) AUDIO : This key is used to select the soundtrack list for the current 2) MUTE : This key is used to toggle between normal and muted audio. -
Page 6: Front Panel
4. 3. REAR PANEL 4.2. FRONT PANEL 1) LNB IN : This is to Connect the coaxial cable from LNB of your Dish. 2) IF OUT : This is to enable the connection of an other receiver, The receiver is provided with this port. 1) POWER : Push the receiver on and off (stand by). -
Page 7: Menu Guide
. MENU GUIDE The main menu is classified into five menus which will carry out the various operation individually. Main Menu d. LNB High : You can select the LNB Frequency. Using the volume “UP/DOWN”(◀∙▶) keys or numeric keys. Press the “MENU” key in the RCU. You will see e. -
Page 8: System Configuration
5.1.3 Factory Default d. UHF Channel : You can select the UHF channel (21 ~ 69) using the volume “UP/DOWN”(◀∙▶) keys. To reset the receiver, select “Factory Default” in e. OSD Language : You can select the OSD language (Menu language) using the “Installation”... -
Page 9: Parental Lock
c. Move channel : Press “F3” to move the channel in the the channel list. a. Receiver Lock: Select “On” to have Receiver Lock. d. Edit channel name : Press “F4” to rename the channel in the the channel list. b. -
Page 10: Common Interface
. TROUBLE SHOOTING There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below . If you can’t solve the problem even after referring this trouble shooting, please 5.6.2. Teletext contact the dealer. -
Page 11: Technical Specifications
. TECHNICAL SPECIFICATIONS 1. Power Supply Symptom Cause Result Type : SMPS The satellite dish is not Input Voltage : 95�240VAC 50/60 Hz Adjust the dish. pointing at the satellite. Fuse Rating : 250V/T2A Connect the signal attenuator Signal too strong to the LNB input. - Page 12 5. Audio Decoder : MPEG-1 ISO/IEC 11172-3 System Decoding Layer I & II : Mono, Dual, Stereo, Joint Stero Audio Mode : 32, 44.1, 48 KHz Sampling Frequency 6. Audio/Video Output : CVBS, RGB, Audio L/R TV SCART : CVBS, Audio L/R VCR SCART : CVBS, Audio L/R RCA Jack...