Related Manuals for Garmin NTX54-Nissan
Summary of Contents for Garmin NTX54-Nissan
- Page 1 3950 NW 120 Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NTX54-Nissan Nissan/Infiniti Garmin Navigation System NTV-KIT405 DS, BM July 8, 2013 NTV-DOC138...
- Page 2 Included Parts: Garmin Navigation system and GPS antenna OEM Nissan touch NTX54-Nissan module NTV-NAV009 screen monitor NTV-ASY184 NTV-NAV010 NTX54 Power T-Harness NTV-HAR232 USB Cable NTV-CAB009 LCD Trim kit (optional) NTV-431 NTX54 Screen T-Harness Garmin Harness NTV-HAR233 NTV-HAR225 Needed Tools: Plastic panel tool...
- Page 3 Video Navigation Power T-Harness Video T-Harness (upda input Harness tes) NTX54-Nissan Module pin out (wire side) Speaker OUT + Speaker OUT - In From Radio + In From Radio - Power T-Harness (18-pin) Video T-Harness (22-pin) Navigation Harness (24-pin) The connector pin outs above are for the black mini Molex connectors that plug into the NTX-NIS/INF interface module.
- Page 4 Overview: The NTX Nissan/Infiniti is a touch screen Navigation interface for compatible 2008 to current Nissan and Infinity vehicles. The module will also allow the integration of a video source or a front facing camera. During the installation the original color LCD monitor will be replaced. The installation is performed entirely AT THE RADIO and not at the monitor.
- Page 5 Gently pull the top section back and away from the dash to Remove the screws from the left and right release the top clips. Make sure that the vehicle is off and bottom corners and pull the HVAC panel disconnect all the harnesses from the back of the HVAC panel. from the bottom up and away from the DO NOT turn the key or push the push to start button until dash.
- Page 6 Swing the bottom of the monitor upwards to release the Pull the radio out of the dash, disconnect all top of the monitor brackets from their U shaped top wiring and set aside. mount. Note: There are no top bolts and only a locking mount.
- Page 7 Using a soft pry tool, pry around the outside of Remove the screws around the monitor the HVAC fascia to release the clips all the way bracket, unplug the monitor and set the around. Pull the entire fascia towards the back monitor and bracket aside.
- Page 8 Screen Replacement FX. 1. Follow the directions on the previous page under "Screen Replacement All Vehicles except FX" to remove the factory monitor from the mounting bracket. 2. The original monitor in the FX has an oversized monitor housing. In order to replace the original monitor with the new touch screen monitor you must use the included (FX Kit only) trim, shims and longer replacement screws to center the new monitor in the mounting brackets.
- Page 9 Installation of the T-harnesses for all vehicles 1. Plug the female end of the 24 pin Video T-Harness into the factory male 24 pin plug behind the radio. 2. Plug the female end of the 20 pin Power T-harness into the factory male 20 pin plug behind the radio. 3.
- Page 10 9. Plug the 18 pin extension harness (black molex plug) into the NTX54-Nissan interface port labeled ‘Radio’. 10. Plug the black 24 pin molex of the Navigation harness into the NTX54-Nissan interface port labeled ‘Navigation’. 11. If the vehicle DOES NOT have Bose, the turn-by-turn directions and all audio commands will be heard automatically through the driver's front speaker.
- Page 11 15. Run the GPS antenna cable to the NTX54 navigation box and plug it into the GPS antenna connector jack. Excess cable should be looped neatly into a circle to eliminate NTX-54 Garmin Navigation kinking of the cable and zip tied securely inside the dash or kick panel.
- Page 12 Setup: IF YOU ARE NOT INSTALLING ANY AFTERMARKET CAMERAS OR VIDEO INPUT, SKIP THIS SECTION AND GO STRAIGHT TO THE "OPERATION" SECTION. Quick Start User’s Guide NTX-54 Nissan/Infiniti Navigation System Programming PINK ‘INPUT’ wire for REV Cam: wire: When this wire is programmed, the screen will display ‘Aux Video’...
- Page 13 Operation: Note: For Video input: This will only display the AFTERMARKET camera/video source from the NTX54 module and will not force the factory rear view camera on if equipped. 13 | P a g e Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase.
- Page 14 A. Verify that the external speaker is plugged into the Garmin harness (if BOSE equipped). If not BOSE equipped, make sure the 3.5mm audio cable (part of the GARMIN harness) is connected to the 3.5mm audio input of the same harness.