ORDER NO. MTNC010837A1 Service Manual Color Television Simplified Manual (NA8MS) Panasonic Models Chassis CT-24SX11E AP367 CT-24SX11UE AP367 CT-24SX11CE AP367 This Simplified Service Manual is issued to add listed models to the Main Service Manual order No. MTNC010527C1 (CT-27SX31E). A set of schematics, unique settings and a complete parts list are included in this Manual.
Important Safety Notice Special components are used in this television set which are important for safety. These parts are identified on the schematic diagram by the symbol and printed in BOLD TYPE on the replacement part list. It is essential that these critical parts are replaced with the manufacturer’s specified replacement part to prevent X-ray radiation, shock, fire or other hazards.
Service Notes (Continued) WARNING: This Receiver has been designed to meet IMPORTANT: To protect against possible damage to the solid state devices due to arcing or static or exceed applicable safety and X-ray radiation discharge, make certain that all ground wires and CTR protection as specified by government agencies and DAG wire are securely connected.
Receiver Feature Table FEATURE/MODEL CT-24SX11E/CE/UE Chassis AP367 Tuning system # of channels Menu language Eng/Span/Fr Closed Caption V-Chip 75 Ω input Remote Model # EUR511502 Picture tube A60LUQ085X PureFlat Picture Tube Comb Filter 3 Line Digital V. Edge Correction V/A norm Both Color Temp.
Location of Controls (Remote) POWER Button Press to turn ON and OFF. MUTE Button Press to mute sound. A second press resumes sound. Press also to access and delete Closed Caption display. VCR, DVD, LD/CD, AUX, TV, CBL, DBS, RCVR Component function buttons VOL (volume) Buttons Press to adjust TV sound level.
Service Mode (Electronic Controls) This Receiver has electronic technology using the I²C Bus Concept. It performs as a control function and it replaces many mechanical controls. Instead of adjusting mechanical controls individually, many of the control functions are now performed by using “On Screen Display Menu”. (The Service Adjustment Mode.) Note: It is suggested that the technician reads all the way through and understand the following procedure for Entering/Exiting the Service Adjustment Mode;...
Press the Power Button on the Remote Control to select the Service Adjustment. For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the value set (b in Fig. 3 ) for Remote Control to select one of Remote Control to adjust the the available Service Adjustments each...
Page 9
Press the Power Button on the Remote Control to select the Service Adjustment For Adjustments: Note: Write Down the original 1.Press Channel Up/Down on the 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 3 ) for Remote Control to adjust the the available Service Adjustments each...
Page 10
Press the Power Button on the Remote Control to select the Service Adjustment For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 3 ) for Remote Control to adjust the the available Service Adjustments each...
Page 11
Press the Power Button on the Remote Control to select the Service Adjustment Adjustments: Note: Write Down the original 1.Press Channel Up/Down on the 2.Press Volume Up/Down on the value set (b in Fig. 3 ) for Remote Control to select one of Remote Control to adjust the the available Service Adjustments each...
Page 12
Press the Power Button on the Remote Control to select the Service Adjustment For Adjustments: 1.Press Channel Up/Down on the Note: Write Down the original 2.Press Volume Up/Down on the Remote Control to select one of value set (b in Fig. 3 ) for Remote Control to adjust the the available Service Adjustments each...
Tint/Color Adjustment 2. HIGH LIGHT areas – In Service Mode for making electronic adjustments, select Drive (C04) GRN, Service DAC Adjustment (B01) (B00) (C05) BLU and adjust the picture for warm whites. Preparation: 1. Apply a rainbow color bar signal. Complete Adjustment 2.
Page 14
15. Press the R-Tune key on the Remote 170±2V DC 0V DC (Ground) Figure 7. KR Waveform 16. In the Service Mode select the DAC DRIVE adjustments (C04) GRN, (C05) BLUE and adjust for warm white in a white color bar pattern. 17.
Chassis Service Adjustment Procedures All service adjustments are factory preset and should not require adjustment unless controls and/or associated components are replaced. Note: Connect the (-) lead of the voltmeter to the appropriate ground. Use heat sink when the HOT ground symbol ( ) is used.
REPLACEMENT PARTS LIST Model:CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION C368 ECQV1H224JL3...
REPLACEMENT PARTS LIST Model: CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION C564 ECKR2H471KB5...
Page 20
REPLACEMENT PARTS LIST Model:CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION C2333 ECA1EM100B...
Page 21
REPLACEMENT PARTS LIST Model: CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION D561 MA165TA5VT...
Page 22
REPLACEMENT PARTS LIST Model:CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION L951 EXCELSA24T...
Page 23
REPLACEMENT PARTS LIST Model: CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION R042 ERJ6GEYJ102V...
Page 24
REPLACEMENT PARTS LIST Model:CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION R542 ERJ6GEYJ272V...
Page 25
REPLACEMENT PARTS LIST Model: CT-24SX11E, CT-24SX11UE, CT-24SX11CE Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION R960 ERQ14AJ100E...
C- Board Schematic, Layout & Voltages - Diagrama Eléctrico, Diagrama Impreso y Voltajes Tarjeta-C ALL MODELS Schematic Notes Resistors are carbon 1/4W unless noted (BOLD LINE) indicates the otherwise. route of B+ supply. Capacitors are ceramic 50V unless noted The schematic diagrams are current at otherwise.
A-Board Schematic, Right Portion - Diagrama Eléctrico de la Tarjeta-A, Sección Derecha ALL MODELS IMPORTANT SAFETY NOTICE THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL FEATURES THAT ARE IMPORTANT FOR PROTECTION FROM X-RADIATION, FIRE AND ELECTRICAL SHOCK HAZARDS. WHEN SERVICING IT IS ESSENTIAL THAT ONLY MANUFACTURERS SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS DESIGNATED WITH A THE SCHEMATIC.