Electrical Connections - JVC 1009DTSMDTJEIN Instructions & Installation Manual

Category Menu item
2
SSM * • SSM 01 – 06
• SSM 07 – 12
• SSM 13 – 18
AREA • AREA US
• AREA EU
• AREA SA
MONO * 2 • MONO ON
• MONO OFF
IF BAND • AUTO
• WIDE
FADER * 3 R06 – F06 [ 00 ] : Adjust the front and rear speaker output balance.
BALANCE * 4 L06 – R06 [ 00 ] : Adjust the left and right speaker output balance.
LOUD • LOUD ON
• LOUD OFF
AUX AUX ADJ 00 —
ADJUST * 5 AUX ADJ 05
L/O MODE • SUB.W
• REAR
SUB.W • LOW
6
FREQ * • MID
• HIGH
SUB.W
SUB.W 00 —
6 SUB.W 08
LEVEL *
[ SUB.W 04 ]
BEEP • BEEP ON
• BEEP OFF
7
AMP GAIN * • LOW POWER
• HIGH POWER
8
AM * • AM ON
• AM OFF
9
AUX IN * • AUX ON
• AUX OFF
2
* Displayed only when the source is "FM."
* 3 If you are using a two-speaker system, set the fader level to "00."
4
* This adjustment will not affect the subwoofer output.
5
* Displayed only when <AUX IN> is set to <AUX ON>.
6
* Displayed only when <L/O MODE> is set to <SUB.W>.
7
* The volume level automatically changes to "VOLUME 30" if you change to <LOW POWER> with the volume level
set higher than "VOLUME 30."
8
* Displayed only when any source other than "AM" is selected.
9
* Displayed only when any source other than "AUX IN" is selected.
Installation
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems. If your vehicle does not have this system, a
voltage inverter is required, which can be purchased at JVC car
audio dealers.
Warnings
• To prevent short circuits:
– Disconnect the battery's negative terminal and make all electrical connections before installing the unit.
– Cover the terminals of the UNUSED leads with insulating tape.
• Be sure to ground this unit to the car's chassis again after installation.
• Replace the fuse with one of the specified rating.
• Connect speakers with a maximum power of more than 50 W (impedance of 4 Ω to 8 Ω). Otherwise, change
the <AMP GAIN> setting. (See "Menu operations.")
• The heat sink becomes very hot after use. Be careful not to touch it when
removing this unit.
PRECAUTIONS on power supply and speaker connections
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your
car.
Parts List
A Control panel.........................................................................1
B Sleeve .........................................................................................1
C Trim plate .................................................................................1
Selectable setting, [ Initial: Underlined ]
: For settings, see "Automatic presetting (FM)—SSM (Strong-
station Sequential Memory)" on page 2.
: When using in North/Central/South America. AM/FM
intervals are set to 10 kHz/200 kHz.
: When using in any other areas. AM/FM intervals are set to
9 kHz/50 kHz (100 kHz during auto search).
: When using in South American countries where FM interval
is 100 kHz. AM interval is set to 10 kHz.
: Activate monaural mode to improve FM reception, but
stereo effect will be lost.
: Restore the stereo effect.
: Increases the tuner selectivity to reduce interference noises
between adjacent stations. (Stereo effect may be lost.)
: Subject to interference noises from adjacent stations, but
sound quality will not be degraded and the stereo effect will
remain.
: Boost low and high frequencies to produce a well-balanced
sound at a low volume level.
: Cancels.
: Adjust the auxiliary input level to avoid the sudden increase
of the output level when changing the source to the external
component connected to the AUX input jack on the control
panel.
: Select if the REAR LINE OUT terminals are used for
connecting a subwoofer (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for
connecting the speakers (through an external amplifier).
: Frequencies lower than 72 Hz are sent to the subwoofer.
: Frequencies lower than 111 Hz are sent to the subwoofer.
: Frequencies lower than 157 Hz are sent to the subwoofer.
: Adjust the subwoofer output level.
: Activates the keypress tone.
: Deactivates the keypress tone.
: VOLUME 00 – VOLUME 30 (Select if the maximum power
of each speaker is less than 50 W to prevent damaging the
speakers.)
: VOLUME 00 – VOLUME 50
: Enable "AM" in source selection.
: Disable "AM" in source selection.
: Enable "AUX IN" in source selection.
: Disable "AUX IN" in source selection.
Prepare these before installation....
D Power cord ..............................................................................1
E Handles .....................................................................................2
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
In-dash mounting
When installing the unit without using the
sleeve
Flat head screws—M5 × 8 mm (3/8") *
Pocket

Electrical connections

IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended
for connection between the unit and your car.
• Consult your JVC car audio dealer or a company supplying kits for details.
Connecting the external amplifier or subwoofer
Signal cord (not supplied)
* Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place
uncoated with paint.
Antenna terminal
White
Heat sink
Front speaker
White (black stripe)
(left)
Gray
Gray (black stripe)
Front speaker
(right)
Green
Rear speaker Green (black stripe)
(left)
Purple
Rear speaker Purple (black stripe)
(right)
3
When you stand the unit, be careful not to damage
the fuse on the rear.
Bend the appropriate
tabs to hold the sleeve
firmly in place.
Removing the unit
Release the rear section first...
* Not supplied.
Bracket *
Y-connector (not supplied)
Remote lead
JVC Amplifier Rear speakers or subwoofer
Make the <L/O MODE> setting accordingly.
* (See "Menu operations.")
15 A fuse
Rear ground terminal
Black
To the metallic body
or chassis of the car
Yellow *
To a live terminal
(constant 12 V)
Red To an accessory
terminal
Blue (white stripe)
* Before checking the operation of this unit prior to installation, this lead
must be connected; otherwise, the power cannot be turned on.
Do the required
electrical
connections.
Install the unit at an
angle of less than 30˚.
To the blue (white stripe)
lead of the unit
Reset the unit
Ignition switch
Fuse block
To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)