Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for VuQube VQ4000
- Page 1 ® Gyro Stabilized In-Motion Satellite System Model VQ4000 Operating Instructions ® Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com 20461 REV C...
-
Page 3: Table Of Contents
The satellite TV market is expanding and changing. The information in this manual was accurate at the time of printing. If your VuQube does not operate as outlined in this manual please call King Controls at (800) 982-9920 or visit our website at www.kingcontrols.com. -
Page 4: Introduction
Power Supply Supplies proper operating voltage to the VuQube. IMPORTANT! The VuQube is intended for at dock or calm water conditions. Note: A TV, satellite receiver and program subscription are also required for satellite TV viewing (sold separately). You must have an HD Receiver, HDTV Monitor (TV), the proper HD cables (component video or HDMI) and the appropriate programming subscription in order to view HD programming (sold separately). -
Page 5: Definition Of Terms
DEFINITION OF TERMS SECTION 2 AZIMUTH: Angle in degrees measured clockwise from Magnetic North (0°) (Fig. 2). Fig. 2 IMPORTANT! There must be a clear “line of sight” to the satellite. Antennas, masts, obstructions on the vessel, etc. can all block the satellite signal from reaching the dish. ELEVATION: Angle in degrees measured from a level plane (Fig. -
Page 6: Vuqube Setup
VUQUBE SETUP SECTION 3 1. Unpack and identify all components (Fig. 4). Fig. 4 2. Place the antenna unit in an area with a clear view to the southern sky (Fig. 5). The antenna unit should be as far as possible from objects like masts, antennas, etc. that can block the satellite signal. - Page 7 Note: When the power supply is connected, the controller should turn on for 3 seconds and then turn off. If the controller stays on, Press the ENTER and “-” buttons simultaneously to turn unit off. 3. Make connections as shown (Fig 6). ALWAYS CONNECT THE POWER SUPPLY LAST. Fig. 6 VQ4000 Wiring Diagram Page 5...
-
Page 8: Operation
Note: This example is for the DTV 101 satellite in Region 2-North Central. The information on your controller will vary depending on the satellite and region you have chosen. Note: The VuQube must remain powered on to maintain a signal. To turn the VuQube off, simultaneously press ENTER and ”-”. - Page 9 AUTOMATIC SATELLITE SWITCHING DIRECTV: Before using the automatic switching feature, you must configure the VuQube and your receiver for your desired option. For switching options see page 10 Dish Network - ExpressVu: Before using the automatic switching feature, you must configure the VuQube and your receiver for your desired option.
- Page 10 SET SATELLITE SERVICE SATELLITE LIBRARY DTV 101 DIRECTV at 101 DTV 101/ 110 hd DIRECTV HDTV at 101 and 110 DTV 101/ 119 DIRECTV HDTV at 101 and 119 Sat 110 Dish Network at 110 Sat 119 Dish Network at 119 DISH 61 Dish Network at 61 DISH 129...
- Page 11 SET REGION (OPTIONAL) Note: To reduce satellite acquisition time, you can set your current region. REGION OPTIONS: NORTH WEST NORTH CENTRAL NORTH EAST CENTRAL WEST MIDDLE CENTRAL CENTRAL EAST SOUTH WEST SOUTH CENTRAL SOUTH EAST ALL REGIONS RECALIBRATE Page 9...
-
Page 12: Automatic Satellite Switching (Directv )
AUTOMATIC SATELLITE SWITCHING SECTION 5 DIRECTV DIRECTV 101 SATELLITE ONLY To receive programming from the DIRECTV 101 satellite only, choose the DTV 101 option (see procedure on page 8), and make sure your receiver is set for round dish-1 satellite (do this through the receiver’s satellite set-up menu screens). - Page 13 This page intentionally left blank. Page 11...
-
Page 14: Automatic Satellite Switching
Dish Network - ExpressVu DISH 500 FOR DISH NETWORK The VuQube will automatically switch between the 110 and 119 satellites for Dish Network by using the receiver’s remote control, after the receiver has been properly configured. Follow the instructions on pages 13-15. -
Page 15: Satellite Receiver Configuration
SATELLITE RECEIVER CONFIGURATION IMPORTANT! The antenna must be on the ground, dock or motionless platform with no movement in order to configure the DISH HD receiver. For automatic satellite switching, King Controls recommends using a Dish Network model 311 receiver for Dish 500, and a Dish Network model VIP211 or a VIP211k HDTV receiver for Dish 1000/1000a. - Page 16 4. Press Wait for dish to lock onto satellites, and controller to display: 5. On the receiver remote, press menu, 6, 1, 1. 6. Highlight Check Switch and press Select. 7. Make sure Superdish and Alternate boxes are NOT selected. 8.
- Page 17 11. DISH 1000/1000a ONLY: Verify your saved settings show your desired satellite trio (110, 119, 129 or 110, 119, 61). You can now use the automatic satellite switching feature of your VuQube. Dish Network HDTV: Dish Network 1000 and 1000a: Changing the Satellite Trio IMPORTANT! Perform the procedure below only if you are unable to receive all of your HD programming in a particular area of the country.
-
Page 18: Troubleshooting
TROUBLESHOOTING SECTION 7 SYMPTOM POSSIBLE SOLUTION Controller does not power up. Check: controller is connected to power supply. power supply is plugged into 110 VAC outlet. Controller remains in one of the Unplug controller from power supply for 10 seconds, then plug back in. following conditions: Check coax cable connection between controller and antenna unit. - Page 19 SYMPTOM POSSIBLE SOLUTION Unit never locks on or locks on Atmospheric moisture. Unit will lock on as weather improves. and drifts off of satellite. Check for obstruction in sky in direction of satellite. Select another satellite and verify unit locks on. Verify coax cables are properly terminated with SNAP-N-SEAL ®...
- Page 20 OPTION 21 RE-INITIALIZE and 0 RECALIBRATE Page 18...
- Page 21 Page 19...
-
Page 22: Security Bracket
SECURITY BRACKET SECTION 8 The VuQube can be secured to an object using a padlock and cable (Fig. 6). Fig. 6 Page 20... -
Page 23: Maintenance
Periodic washing of the enclosure with mild soap and water is recommended. If you plan on not using your VuQube for long periods of time, it is recommended that the system be put through a search procedure on a quarterly basis to keep all moving parts in good working order. -
Page 24: Limited Warranty
LIMITED WARRANTY SECTION 10 Every VuQube Satellite System is thoroughly inspected and tested before leaving the factory. It is covered by a one year parts limited warranty from the date of original purchase. This warranty does not cover installation and external wiring or refurbished units. - Page 25 Notes: Page 23...
- Page 26 Notes: Page 24...
- Page 28 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com ®...