Pour l’installation et les raccordements, se référer au manuel séparé. INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D’INSTRUCTIONS KD-SX850/SX750 KD-SX850/SX750 KD-SX850/SX750 KD-SX850 45Wx4 CD CHANGER CONTROL DISP SCAN KD-SX750 45Wx4 CD CHANGER CONTROL DISP SCAN COMPACT DIGITAL AUDIO FM/AM COMPACT DIGITAL AUDIO FM/AM COMPACT...
INFORMATION (For USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. CONTENTS BASIC OPERATIONS ... 4 RADIO OPERATIONS ... 5 Listening to the radio ... 5 Storing stations in memory ...
BASIC OPERATIONS Note on One-Touch Operation: When you select a source in step 2 below, the power automatically comes on. You do not have to press this button to turn on the power. FM/AM Adjust the sound as you want (see pages 13 – 18). To drop the volume in a moment Press briefly while listening to any source.
RADIO OPERATIONS Listening to the radio FM/AM To search stations of higher frequencies. To search stations of lower frequencies. To stop searching before a station is received, press the same button you have pressed for searching. To tune in a particular frequency without searching: 1 Select the band (FM or AM).
Storing stations in memory You can use one of the following two methods to store broadcasting stations in memory. • Automatic preset of FM stations: SSM (Strong-station Sequential Memory) • Manual preset of both FM and AM stations FM station automatic preset: SSM You can preset 6 local FM stations in each FM band (FM1, FM2, and FM3).
Manual preset You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually. EXAMPLE: Storing an FM station of 88.3 MHz into the preset number 1 of the FM1 band FM/AM Repeat the above procedure to store other stations into other preset numbers.
Tuning into a preset station You can easily tune into a preset station. Remember that you must store stations first. If you have not stored them yet, see pages 6 and FM/AM Select the band (FM1, FM2, FM3 or AM) you want.
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “BEEP**”, “AREA” or "LINE IN*" appears on the display. Displayed only when one of the following sources is selected — FM, AM and CD. (only for KD-SX750) ** (only for KD-SX850) 2 If “AREA” does not appear, press 3 Rotate the control dial clockwise.
CD OPERATIONS Playing a CD Total playing time of the inserted disc Note on One-Touch Operation: When a CD is already in the loading slot, pressing CD turns on the unit and starts playback automatically. CAUTION on Volume Setting CDs produces very little noise compared with other sources. If the volume level is adjusted for the tuner, for example, the speakers may be damaged by the sudden increase in the output level.
Locating a track or a particular portion on a CD To fast forward or reverse the track Press and hold Press and hold To go to the next track or the previous track Press the next track. Each time you press the button consecutively, the beginning of the next tracks is located and played back.
Selecting CD playback modes To play back tracks at random (Random Play) You can play back all tracks on the CD at random. Each time you press MO/RND (Mono/Random) while playing a CD, CD random play mode turns on and off alternatively. When the random mode is turned on, the RND indicator lights up on the display and a track randomly selected starts playing.
SOUND ADJUSTMENTS Adjusting the sound You can adjust the sound characteristics to your preference. Indication Adjust the bass (Bass) Adjust the treble (Treble) Adjust the front and rear speaker (Fader)* balance Adjust the left and right speaker (Balance) balance Adjust the volume (Volume) Note: * If you are using a two-speaker system, set the fader level to “00.”...
Turning on/off the BBE function The BBE * function restores the brilliance and clarity of the original live sound in recording, broadcasts, etc. When a speaker reproduces sound, it introduces frequency-dependent phase shifting, causing high-frequency sounds to take longer to reach the ear than low frequency sounds. The BBE function adjusts the phase relationship between the low, mid and high frequencies by adding a progressively longer delay time to the low and mid frequencies, so that all frequencies reach the listener’s ears at the proper time.
Using the Sound Control Memory You can select and store a preset sound adjustment suitable to each playback source. (Advanced SCM) Selecting and storing the sound modes Once you select a sound mode, it is stored in memory, and will be recalled every time you select the same source.
Recalling the sound modes FM/AM Notes: • You can adjust each sound mode to your preference, and store it in memory. If you want to adjust and store your original sound mode, see “Storing your own sound adjustments” on page 18. •...
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “BEEP or “LINE IN*” appears on the display. * Displayed only when one of the following sources is selected — FM, AM and CD. (ONLY FOR KD-SX750) ** (ONLY FOR KD-SX850) Select “SCM LINK” if not shown on the display.
Storing your own sound adjustments You can adjust the sound modes (BEAT, SOFT, POP: see page 15) to your preference and store your own adjustments in memory. Within 5 seconds Within 5 seconds Within 5 seconds Repeat the same procedure to store other settings. To reset to the factory settings Repeat the same procedure and reassign the preset values listed in the table on page 15.
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “BEEP or “LINE IN*” appears on the display. * Displayed only when one of the following sources is selected — FM, AM and CD. (ONLY FOR KD-SX750) ** (ONLY FOR KD-SX850) Set the hour.
To check the current clock time (changing the display mode) Press DISP repeatedly. Each time you press the button, the display mode changes as follows. During tuner operation: Frequency During CD changer operation: Elapsed playing time • If the unit is not in use when you press DISP, the power turns on, the clock time is shown for 5 seconds, then the power turns off.
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “BEEP or “LINE IN*” appears on the display. * Displayed only when one of the following sources is selected — FM, AM and CD. (ONLY FOR KD-SX750) ** (ONLY FOR KD-SX850) Select “LEVEL” if not shown on the display.
Turning on/off the key-touch tone This section is ONLY FOR KD-SX850. You can deactivate the key-touch tone if you do not want to make it beep when you press a button. When shipped from the factory, the key-touch tone is activated. •...
To adjust the line input level This section is ONLY FOR KD-SX850. Adjust the line input level properly when an external component is connected to the LINE IN jacks. When shipped from the factory, the line input level is set at level 00. If the input level of the connected component is not high enough, increase the input level properly.
Detaching the control panel You can detach the control panel when leaving the car. When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. How to detach the control panel Before detaching the control panel, be sure...
REMOTE OPERATIONS Before using the remote controller: • Aim the remote controller directly at the remote sensor on the main unit. Make sure there is no obstacle in between. • Do not expose the remote sensor to strong light (direct sunlight or artificial lighting).
Using the remote controller RM-RK31 For KD-SX750 RM-RK32 For KD-SX850 1 Functions the same as the 2 • Functions as the BAND button while listening to the radio. Each time you press the button, the band changes. • Functions as the DISC + button while listening to the CD changer.
We recommend that you use one of the CH-X series with your unit. If you have another CD automatic changer, consult your JVC car audio dealer for connections. • For example, if your CD automatic changer is one of the KD-MK series, you need a cord (KS- U15K) for connecting it to this unit.
To fast forward or reverse the track Press and hold Press and hold To go to the next track or the previous track Press the next track. Each time you press the button consecutively, the beginning of the next tracks is located and played back. Press current track.
Selecting CD playback modes To play back tracks at random (Random Play) Each time you press MO/RND (Mono/Random) while playing a CD, CD random play mode changes as follows: Mode RND Indicator RND1 Lights RND2 Flashes To play back tracks repeatedly (Repeat Play) Each time you press RPT (Repeat) while playing a CD, CD repeat play mode changes as follows: Mode...
EXTERNAL COMPONENT OPERATIONS External component operations This section is ONLY FOR KD-SX750. You can connect the external component to the CD changer jack on the rear using the Line Input Adaptor KS-U57 (not supplied). Preparations: • For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume).
Selecting the external component to use You can connect the external component to the CD changer jack on the rear using the Line Input Adaptor KS-U57 (not supplied). To use the external component as the playback source through this receiver, you need to select which device —...
Playing VCRs This section is ONLY FOR KD-SX850. After connecting a VCR (KZ-V10) to the LINE IN plugs, you can perform the following operations. You can also connect the TV to this unit. Note on One-Touch Operation: When you press CD-CH/EXT, the power automatically comes on. You do not have to press to turn on the power.
Handling CDs This unit has been designed only to reproduce the CDs bearing the Other discs cannot be played back. How to handle CDs When removing a CD from its case, press down the center holder of the case and lift the CD out, holding it by the edges. •...
TROUBLESHOOTING What appears to be trouble is not always serious. Check the following points before calling a service center. Symptoms • CD cannot be played back. • CD sound is sometimes interrupted. • Sound cannot be heard from the speakers. •...
AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 45 W per channel Rear: 45 W per channel Continuous Power Output (RMS): Front: 17 W per channel into 4 , 40 Hz to 20,000 Hz at no more than 0.8% total harmonic distortion. Rear: 17 W per channel into 4 , 40 Hz to 20,000 Hz at no more than 0.8% total harmonic distortion.
Having TROUBLE with operation? Please reset your unit Refer to page of How to reset Still having trouble?? USA ONLY Call 1-800-252-5722 http://www.jvcservice.com We can help you! VICTOR COMPANY OF JAPAN, LIMITED EN, SP, FR 1299HISFLEJES...