600mm 4 burner stainless steel gas cooktop (8 pages)
Summary of Contents for IAG ICS6SE3
Page 1
600mm Electric Cooktop with Solid Elements Manual MODEL ICS6SE3 Installation and Operation...
Page 2
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual Congratulations on choosing one our appliances, we hope you have many reliable years of use from this new appliance. We recommend that you read this manual for best performance and to extend the life of your appliance. You should keep this manual in a safe place and accessible place should future reference be required. Thank you. NOTE : This User Instruction Manual contains important information, including safety & ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance . Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Technical service Department. General Information This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.. IMPORTANT: The adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature of 85°C above the ambient temperature of the room it is located in, whilst in use. Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage or discolouration at temperatures below the guidelines given above. During normal use some discolouration may occur from excessive heated generated by the solid hotplates, Any damage caused by the appliance being installed in contravention of this temperature limit, will be the liability of the owner. Your new appliance is guaranteed against electrical or mechanical defects. The foregoing does not affect your statutory rights. The use of this appliance for any other purpose or in any other environment without the express agreement will invalidate any warranty or liability claim. You should not use this appliance to store items on or as a work surface. No modifications to the appliance are permitted. ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual INSTALLATION This appliance must be correctly installed by a suitably qualified person, strictly in accordance with the manufacturer’s instructions. Please see the specific section of this booklet that refers to installation. SPECIFICATIONS ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual Hob surface layout 1500 watt 2000 watt thermostatic thermostatic element element Control knobs indicator On / Off 2000 watt 1500 watt thermostatic ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual Turning on an element and setting a power level Turn the control knob of the zone that you wish to cook on, clockwise or anticlockwise until it reaches the power level that you desire. Each cooking zone can be adjusted between 1 and 6, one being the coolest zone setting and six being the hottest zone setting. When you have finished cooking, make sure that you turn the control knob anti‐clockwise, to the 0 position. Hob guidelines The first few times the hob top is used, it may give off an acrid, burning smell. This smell will disappear completely with repeated use. The hob surface is fitted with cooking areas of different diameter and power. You should not use saucepans with rough bottoms, as this can scratch the solid plates. Before use, make sure that the bottoms of the saucepans are clean and dry. When cold, the bottom of the pans should be slightly concave, as they expand when hot and lie flat on the surface of the hob. This will allow the heat to transfer more easily. The best thickness for the bottom of the pans is 2 – 3 mm of enameled steel and 4 – 6 mm for stainless steel with sandwich type bottoms. If these rules are not followed, then there will be a great loss of heat and energy. Heat not ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual After each use Wipe the appliance over with a damp cloth and a little washing up liquid. Dry the appliance by rubbing the surface with a clean cloth. If the hob top is heavily soiled then if the hob surface is made from stainless steel, then a suitable stainless steel cleaner should be used. IMPORTANT: If a stainless steel cleaner is not used regularly, then it is possible for the surface of the hob to change colour over a period of time. For other hob surfaces, a cleaner such as “Hob Brite” or “Bar Keepers Friend” may be appropriate. Maintaining the solid plates If something is spilt onto the plate itself, then it can be removed using a soft brush, plastic or nylon scourer and warm water. To keep the solid plates in good condition, you should put a little olive oil onto a kitchen towel and rub it onto the surface of the plate. The next time the plate is used, then it may produce a little smoke. Alternatively you can use a hotplate conditioner; these products can normally be found at larger supermarkets and hardware stores. The manufacturer’s instructions should be followed when using these products. IMPORTANT: If the solid plates are not maintained regularly with olive oil or a hotplate conditioner, then they may rust. INSTALLATION ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual Positioning (continued) This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending on size) or 600 mm worktop, providing the following minimum distances are allowed: 700 mm between the hob surface and the underside of any horizontal surface above it. 650mm distance between cooktop and base of Rangehood filters should be present.. 50 mm clearance around the appliance and between the hob surface and any combustible materials. Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 Electric cooktop 1 Installation and instruction manual 4 Fixing screws 4 Clamps 1 Sealing strip Installing the appliance ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual Sealing tape Carefully turn the hob upside down and place it on a cushioned mat. Apply the sealing strip provided around the edge of the appliance (see below picture). The protective covering must be removed from both sides. Do not leave a gap in the sealing agent or overlap the thickness. IMPORTANT: Do not use a silicon sealant to seal the appliance against the benchtop. This will make it difficult to remove the hob from the benchtop in future, particularly if it needs to be serviced. Affixing cooktop to benchtop Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it. Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop. Then fully tighten the screws (C) to secure the hob into position. ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual Electrical connection This appliance must be installed by a qualified person. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. WARNING: THIS APPLIANCE MUST BE EARTHED. This appliance must be wired into a 30 A double pole switched fused spur outlet, having 3 mm contact separation and placed in an easily accessible position adjacent to the appliance. It should not be located above the appliance and no more than 1.25m away from it. The spur outlet must still be accessible even when your oven is located in its operating position. Cable type: H05 RRF 3 core x 2.5 mm² Connecting the mains supply cable The mains terminal block is located on the underside of the hob and the terminals are accessible by removing the terminal block cover by removing the cover screw. The cable connections must be in accordance with the diagram located on the bottom of the hob. The brass links must be positioned as marked in the appropriate diagram and once established ALL terminal screws must be tightened down firmly. If when the hob is first switched on, only two of the zones work, you should recheck that the ...
ACS6SE2 and ICS6SE3 60cm Cooktop Installation and Operation Manual MY APPLIANCE IS NOT WORKING PROPERLY The cooking zones are not functioning or will not switch on. Check that the mains electrical supply to the appliance is correct and working. Check the mains ★ fuse. A humming sound is heard when a cooking zone is selected. This is normal; the sound will disappear when the zone heats up. ★ The cooking zones have become discoloured This maybe caused by burnt on remnants of food. This will not affect the working of the appliance. ★ However you should make sure that the cleaning instructions are being followed regularly. Only two of the zones on my hob are working You should recheck that the terminal screws are all fully tightened between the links. ★ IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Service Department . DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge. The appliance must be accessible for the engineer to perform any necessary repair. If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen, then he will not complete a repair. This includes situations where appliances have been tiled in, sealed in with sealant, have ...