CITROËN C4 Quick Start Manual page 2

6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring under the knob and push the gear lever to the
left then forwards.
6-SPEED ELECTRONIC GEARBOX SYSTEM
R. Reverse
N. Neutral.
A. Automatic mode.
M. Manual mode with sequential gear changing.
Moving off
Select position N .
Press the brake pedal down fully.
Start the engine.
Select  rst gear (position M or A ) or reverse (position R ).
Release the parking brake unless it is programmed to automatic
mode.
Take your foot off the brake pedal, then accelerate.
STOP & START
Engine going into STOP mode
The "ECO" warning lamp comes on in the instrument
panel and the engine is put into standby:
- with a manual gearbox ; at speeds below 12 mph (20 km/h),
when you put the gear lever into neutral, and you release the clutch
pedal,
- with the 6-speed electronic gearbox system; at speeds
below 5 mph (8 km/h), when you press the brake pedal or you
put the gear lever into position N.
Fiche_loueur_B71_C4_01-2010_an.i2 2 Fiche_loueur_B71_C4_01-2010_an.i2 2
GEAR SHIFT INDICATOR
System which reduces fuel consumption by advising the driver to
change up on vehicles  tted with a manual gearbox.
AUTOMATIC GEARBOX
P. Park.
R. Reverse.
N. Neutral.
D. Automatic operation.
M+/-. Manual operation with sequential changing of the six gears.
With your foot on the brake, select position P or N .
Start the engine.
With the engine running, press the brake pedal.
Release the parking brake, unless it is programmed to
automatic mode.
Select position R , D or M.
Gradually release the brake pedal.
Engine going into START mode
The "ECO" warning lamp goes off and the engine
restarts:
- with a manual gearbox; when you depress the clutch pedal,
- with the 6-speed electronic gearbox system;
- gear lever in position A or M, when you release the brake
pedal,
- or gear lever in position N and the brake pedal released,
when you put the lever into position A to M,
- or when you engage reverse.
LIGHTING CONTROLS
A. Main lighting mode selection ring: turn it to position the symbol
required facing the mark.
Lamps off.
Automatic illumination of headlamps.
Sidelamps only.
Dipped headlamps or main beam headlamps.
B. Stalk for switching headlamps: pull to switch the lighting between
dipped headlamps/main beam headlamps.
C. Foglamp selection ring.
rear foglamps
front and rear foglamps
SPEED LIMITER
1. Limiter mode On/Off.
2. Decrease the programmed value.
3. Increase the programmed value.
4. Speed limiter On/Off.
5. Display the list of memorised speeds.
CRUISE CONTROL
1. Cruise control mode On/Off.
2. Programme a speed/Decrease the programmed value.
3. Programme a speed/Increase the programmed value.
4. Cruise control Off/Resume.
5. Display the list of memorised speeds.
WIPER CONTROLS
Windscreen wiper
A. Wiping speed control stalk: raise or lower the stalk to the
desired position
Fast wiping (heavy rain).
Normal wiping (moderate rain).
Intermittent wiping (proportional to the speed of the
vehicle).
Park,
Single wipe (press down or pull towards you, then
release).
or
Automatic wiping (press down, then release).
Single wipe (brie y pull the control stalk
towards you).
REAR WIPER
B. Rear wiper selection ring: turn the ring to place the desired
symbol against the marking.
Park,
Intermittent wipe,
Wash-wipe.
Turn the ring to its stop/the rear screen wash, then the
rear wiper operate for a set duration
14/09/2010 13:19:35 14/09/2010 13:19:35