Messages - Panasonic DMP-BD55 Operating Instructions Manual

Messages

The following messages or service numbers appear on the television or unit's display when something unusual is detected during startup and
use.
On the television
Authorisation Error.
This unit is not authorised to
play this title.
Cannot play.
Cannot play on this unit.
No disc is inserted.
Rental Expired.
$ This operation is currently
disabled.
Cannot connect.
Please check the connection of
the LAN cable.
IP address is not set.
Cannot obtain IP address.
Please check the connection or
setting of the router.
This IP address is already in
use.
Please check the setting.
Connection test could not be
conducted.
IP address is not set correctly.
Connection test was
unsuccessful. No reply from
Gateway. Please check the
connection or setting of the
router.
Network connection was
rejected.
Please confirm Setup "BD-Live
Internet Access".
On the unit's display
F99
HDMI ONLY
No PLAY
No READ
PLEASE WAIT
SET
(" " stands for a number.)
UNFORMAT
UNSUPPORT
U59
U72
U73
RQT9245
34
≥[DivX] You are trying to play the DivX VOD content that was purchased with a different
registration code. You cannot play the content on this unit.
≥You inserted an incompatible disc.
≥You tried to play a non-compatible image.
≥Confirm "SD" on the unit's display is not blinking and re-insert the card.
≥The disc may be upside down.
≥[DivX] The DivX VOD content has zero remaining plays. You cannot play it.
≥Some operations are prohibited by the unit or disc. For example;
– [BD-V] :
During play back, reverse slow-motion or reverse frame-by-frame is not possible.
– Depending on the disc, you may not be able to perform search or skip when film previews
and warning screens are being played back.
≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN
terminal connection, cable itself (a cross cable may be used by mistake), etc.
≥The "IP Address" in "IP Address / DNS Settings" is "---. ---. ---. ---". Set the "IP Address",
"Subnet Mask", and "Gateway Address". (Select the automatic address acquisition if
necessary.)
≥If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– Check whether or not the hub's Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
≥This unit's IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP addresses
from being duplicated.
≥Turn the unit off. Remove the AC mains lead and reconnect it and try again. If the same
symptom persists, then consult your dealer.
≥If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– If the hub's Link lamp does not light up, then check the cable connection, LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
≥Check the "IP Address", "Subnet Mask", and "Gateway Address" in the "IP Address / DNS
Settings".
≥If the MAC address information is required, then press [SETUP] to display the "Network
Settings" menu.
≥When you set "BD-Live Internet Access" to "Limit" and play BD-Live contents which do not
have a content owner certificate, the Internet access of the content is not allowed. If you
allow the content to connect to Internet, set "BD-Live Internet Access" to "Permit".
≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby
for 3 seconds. Now press [Í/I] on the main unit again to turn the unit on.
≥Some BD-Video discs can only be output with HDMI.
≥There is a viewing restriction on a BD-Video or DVD-Video.
≥The disc is dirty or badly scratched. The unit cannot play.
≥The unit is carrying out internal process.This is not a malfunction. You cannot operate the
unit while "PLEASE WAIT" is displayed.
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format).
≥You have inserted a disc the unit cannot play.
≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
≥The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is damaged.
Page
20
4, 5
5, 22
—
—
20
—
9
12
9
9
—
—
9
12
12
26
—
—
26
—
—
33
—
4, 5
—
—