Troubleshooting - JVC GR-SXM38U Instructions Manual

Before consulting your JVC dealer, please check the following to see if you can correct the problem
yourself.
Vertical white lines appear when shooting a
very bright object.
• This sometimes occurs when the contrast
between the background and the object is
great. It is not a defect of the camcorder.
Bright, crystal-shaped spots appear in the
LCD monitor and the viewfinder.
• Sunlight is directly entering the lens. This is
not a defect of the camcorder.
Colored bright spots appear all over the
LCD monitor or the viewfinder.
• The LCD monitor and the viewfinder are
made with high-precision
However, black spots or bright spots of light
(red, green or blue) may appear constantly
on the LCD monitor or in the viewfinder.
These spots are not recorded on the tape.
This is not due to any defect of the unit.
(Effective dots: more than 99.99%.)
Animation or Time-Lapse is not available.
• Before recording in the Animation mode at
the very beginning of a tape, set the
camcorder to the Recording mode for about
5 seconds, so that the tape runs smoothly.
Using the Fade-in function at this point is a
good way to begin an animated program (
pg. 15, REC TIME/INT. TIME in SYSTEM
MENU).
The camcorder is a microcomputer-controlled device.
External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In
such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.); and then re-
connect it and proceed as usual from the beginning.
WARNING INDICATIONS:
(high)
power comes close to nil, the battery indicator
exhausted, power turns off automatically.
: Blinks when no cassette is loaded, or when the erase protection tab is not in the position that allows
recording.
TAPE END: Appears when the tape ends during recording, playback or fast-forwarding.
LENS CAP: Appears for 5 seconds after power is turned on if the lens cap is attached.
CONDENSATION OPERATION PAUSED PLEASE WAIT: These 2 warnings appear alternately every 3
seconds if condensation occurs. In this case, all functions except tape eject and power on/off are disabled.
Remove the tape, turn the unit off (without removing the power supply), wait a few minutes for the warnings to
clear, and turn it on again.
HEAD CLEANING REQUIRED USE CLEANING CASSETTE: These 2 warnings appear alternately
every 3 seconds if dirt is detected on the heads during recording. In this case, use an optional cleaning
cassette. If the warning remains after cleaning, consult your nearest JVC dealer.
E01—E06 UNIT IN SAFEGUARD MODE REMOVE AND REATTACH BATTERY: The error indications (E01
— E06) show what type of malfunction has occured. If an error indication and warning appear, turn the unit off,
remove the power supply (battery, etc.) and wait a few minutes for them to clear. When it does, you can
resume using the camcorder. If the indication remains, consult your nearest JVC dealer.

TROUBLESHOOTING

The tape is running, but there is no play-
back picture.
• The TV has not been set to its VIDEO mode
• If A/V connection is used, the TV's VIDEO/
Playback picture is blurred or interrupted.
• The video heads are dirty or worn out.
The tape stops during fast-forwarding or
rewinding.
• The Counter Memory Function has been
technology.
The date and time displays disappear.
• If you remove the power source from the
The tape will not eject.
• The battery pack is running low.
• If the LCD monitor is not open over 60
(exhausted) : Displays the battery remaining power level. As the battery
blinks (battery power warning). When the battery power is
17
or channel.
TV Switch has not been set to VIDEO.
Consult your nearest JVC dealer for head
cleaning or replacement.
activated ( pg. 16, "COUNTER MEMORY").
camcorder while the power is on, all settings
and selections are erased. Make sure to turn
the camcorder's
disconnecting the power source.
degrees, the EJECT button ) does not
function.
power off before