Matrix Amplification XT1000 User Manual
  1. Manuals
  2. Brands
  3. Matrix Amplification Manuals
  4. Amplifier
  5. XT1000
  6. User manual

Matrix Amplification XT1000 User Manual

Xt series amplifier
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XT1000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Matrix Amplification XT1000

Summary of Contents for Matrix Amplification XT1000

  • Page 2: Table Of Contents

    ENSURE ALL WIRING IS SAFE AND CORRECT BEFORE USE. (THIS SYMBOL ALSO UNIVERSALLY FLAGS PLEASE RETAIN ALL FACTORY PACKAGING ELECTRICAL HAZARDS) FOR ANY FUTURE POSTAL TRANSIT. DO NOT OPEN THE AMPLIFIER; LEAVE ALL INTERNAL SERVICE OPPERATIONS TO A QUALIFIED TECHNICIAN. REV.1.17 MATRIX AMPLIFICATION...

  • Page 3: Features And Innovations

    • Temperature regulated, High Speed Fan Cooling. A new high speed fan is utilised to ensure maximum reliability by allowing for far greater cooling latitude (The amplifier vents hot air through rear connector panel). MATRIX AMPLIFICATION REV.1.17...

  • Page 4: Specifications

    Note: Our policy of continuous improvement may lead to the above specifications being exceeded prior to documentation being updated. REV.1.17 MATRIX AMPLIFICATION...

  • Page 5: Basic Schematics

    XT SERIES USER MANUAL 2.2 Basic Schematics. Modes: Output Connections: MATRIX AMPLIFICATION REV.1.17...

  • Page 6: Interface Elements

    These indicators light briefly during the power up cycle and also light should a fault occur. Illumination of the protect indicators, shows that the output of the amplifier has been disconnected by means of an internal relay to protect connected speaker systems from being damaged by the fault. REV.1.17 MATRIX AMPLIFICATION...

  • Page 7: Rear Panel

    Speakon connectors to make connections Cable testers which allow you to hook up both ends of the cable and confirm correct wiring are available and purchasing one as a standard tool for debugging and partial safety assurance is recommended. MATRIX AMPLIFICATION REV.1.17...
  • Page 8 This should be 13 amps for the models listed in this manual. However, if there is any reason to believe that a malfunction caused the fuse to blow, stop using the equipment immediately and take the amplifier to an authorised service engineer for servicing. REV.1.17 MATRIX AMPLIFICATION...

  • Page 9: Recommended Usage

    4 or 8 ohms depending on the model used. Also note the custom wiring required for connecting the speakers in bridged mode. Using Standard connections will result in exceptionally poor performance. MATRIX AMPLIFICATION REV.1.17...
  • Page 10 LIVE end of the second amplifier channel. None of the speaker output terminals should be connected to ground, otherwise damage to the speaker system and the amplifier may occur. REV.1.17 MATRIX AMPLIFICATION...

  • Page 11: Cables, Making Your Own

    Keep cable runs short where possible, however be sure allow a little bit of slack in the length of cable used to make the lead. Stretched, overstressed cables tend to break at the most inconvenient moments. MATRIX AMPLIFICATION REV.1.17...

  • Page 12: Cable Connections

    DF = 430 - 127 (86) DF – Damping Factor est. DF – Damping Factor est. DF – Damping Factor est. wires AWG wires AWG wires AWG Rec Minimum: Rec Minimum: Rec Minimum: Rec Minimum: Rec Minimum: Rec Minimum: Rec Minimum: REV.1.17 MATRIX AMPLIFICATION...
  • Page 13 NEVER Pair together (-) negative/'ground' cables from different ● amplifiers, this will result in amplifier malfunction and can easily result in permanent damage to speaker systems, amplifiers and associated equipment. MATRIX AMPLIFICATION REV.1.17...

  • Page 14: Trouble Shooting

    - especially in bridge mode If any of these, or other symptoms persist, Please contact us with the details below for help, advice and service: Contact Details: Address: MATRIX AMPLIFICATION LIMITED, Matrix Amplification, Little Castle Farm, Email: support@matrix-amplification.com Pen-Y-Park Road,...

  • Page 15: Warranty

    Warranty work can only be performed at our authorised distributors or at Matrix Amplification Limited. We will remedy the defect and ship the product from the service centre or our own factory within a reasonable time after receipt of the defective product. All expenses in remedying the defect, including freight costs from ourselves to you (within mainland UK) will be borne by us.

  • Page 16: Declaration Of Ce Conformity

    Andrew Hunt, MATRIX AMPLIFICATION LIMITED, Cordes House, Factory Road, Newport, Gwent, United Kingdom. NP20 5FA Products: XT1000 / XT2000 Equipment Type: Commercial Audio Power Amplifiers. Safety Standard: AMD1: 2005 and IEC Safety Requirements - Audio Video and Similar Electronic Apparatus.

This manual is also suitable for:

Xt2000

Table of Contents