VWR International 1400E Installation And Instruction Manual

Economy vacuum oven

Advertisement

VWR International 1400E Installation And Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1400E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for VWR International 1400E

  • Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
  • Page 2 ECONOMY VACUUM OVEN : 1400E ODEL NSTALLATION NSTRUCTION ANUAL Sheldon Manufacturing Inc. P.O. Box 627 Cornelius, Oregon 97113 EMAIL: tech@Shellab.com INTERNET: http://www.Shellab.com/~Shellab 1-800-322-4897 (503) 640-3000 FAX (503) 640-1366 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS SECTION 1.0 RECEIVING AND INSPECTION SECTION 2.0 GRAPHIC SYMBOLS SECTION 3.0 INSTALLATION SECTION 4.0 CONTROL PANEL OVERVIEW SECTION 5.0 PRECAUTIONS SECTION 6.0 VACUUM OPERATION SECTION 7.0 OPERATION SECTION 8.0 MAINTENANCE SECTION 9.0 TROUBLESHOOTING AND SERVICE SECTION 10.0 PARTS LIST UNIT SPECIFICATIONS WIRE DIAGRAM...
  • Page 4: Receiving And Inspection

    Section RECEIVING AND INSPECTION IMPORTANT: READ THIS INSTRUCTION MANUAL IMMEDIATELY. Your satisfaction and safety require a complete understanding of this unit, including its proper function and operational characteristics. Be sure operators are familiar with these instructions before attempting to put the unit in service. NOTE: This equipment must be used only for its intended application;...
  • Page 5: Graphic Symbols

    Section GRAPHICS SYMBOLS Your oven is provided with a display of graphic symbols to help in identifying the use and function of the available adjustable components. Indicates that you should consult your operation manual for further description and discussion of a control or user item. Indicates "AC Power On".
  • Page 6: Installation

    The doors should be positively locked in the closed position during transport. Leveling: The unit must sit level and solidly. The Model 1400E has four rubber feet that are already attached to the unit and are not adjustable; however, the counter top must be level for maximum working and safety conditions.
  • Page 7 chamber with a disinfectant that is appropriate for your application. DO NOT USE chlorine-based bleaches or abrasives as this will damage the interior. DO NOT USE spray cleaners that might leak through openings and cracks and get on electrical parts or that may contain solvents that will harm the coatings. A thorough, periodic cleaning is strongly recommended.
  • Page 8: Control Panel Overview

    Section CONTROL PANEL OVERVIEW Figure 2 POWER: The Main Power I/O (ON/OFF) switch controls all power to the oven. It must be in the I, or ON position before any systems are operational. HEATING Light: This pilot lamp is on the when the temperature controller has activated the heating elements to reach and maintain set point.
  • Page 9: Precautions

    Section PRECAUTIONS Do not place or use explosive, combustible, or flammable materials in the oven. Do not use sealed containers in the oven chamber. Do not cut or remove the ground prong from the power cord or use an ungrounded 2-prong adapter plug.
  • Page 10: Vacuum Operation

    A pump with a pumping capacity four times greater than the chamber volume is advisable. The 1400E has a chamber volume of one (1) cubic foot, so a pump with a pumping capacity of four (4) cubic feet per minute is recommended. When working below 1mm, a diffusion type pump will be needed.
  • Page 11 FIGURE THREE Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 12: Operation

    Section OPERATION Power Supply: Connect the service cord to a grounded outlet and push the power switch to the ON position. Place a reference thermometer inside the chamber where it can be easily viewed through the window, then vacuum down the chamber as described in Section 6.0. Setting Temperature: The operating range for this oven is 40°C - 210°C.
  • Page 13: Maintenance

    Section MAINTENANCE Note: Prior to any maintenance or service on this unit, disconnect the service cord from the power supply. Cleaning: Disinfect the oven interior on a regular basis. To prepare the oven for cleaning, remove the shelves and door gasket. The shelves and door gasket are autoclavable.
  • Page 14: Troubleshooting And Service

    Section TROUBLESHOOTING AND SERVICE Always make a visual inspection of the oven and control console when troubleshooting. Look for loose or disconnected wires or tubing, which may be the source of the problem. The oven is designed so that no internal electrical servicing should be required under normal conditions.
  • Page 15 Unit won’t hold vacuum 1/ check door gasket for alignment and damage, wear or lack of compliance 2/ assure all vent and feed valves are closed tightly 3/ assure tight connections to pump OTHER Unit or wall fuse/circuit breaker is blown 1/ check wall power source 2/ compare current draw and compare to specs on data plate...
  • Page 16: Parts List

    Section PARTS LIST Description 115V 220V Control Knob X1000771 X1000771 Door Gasket, Silicone 100029 100029 Door Glass 700027 700027 Heating Element 200114 200114 I/O (ON/OFF) X1000124 X1000124 Pilot Light 200020 200020 Power Cord 100014 101990 Temperature Controller 100026 100026 Thermometer 100030 100030 Vacuum / Vent Valve...
  • Page 17: Wire Diagram

    WIRE DIAGRAM Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 18 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...

Table of Contents