Page 1: Software Version
ST.RE.E10137.3 Issue 3 ENGLISH (UK) REFERENCE GUIDE Voyager E5784 and E5788 HD DSNG Encoder Software Version 3.9.0 E5784/E5788 Encoder...
Page 2 This document and the information contained in it is the property of Issue 3 first published in 2006 by: TANDBERG Television Ltd and may be the subject of patents ANDBERG ELEVISION pending and granted. It must not be used for commercial purposes...
Page 3 Annex J: Setting of the Remux Card for Data/PSIP and DVB- Subtitles Input Annex K: PRO MPEG FEC Support for IP Streaming in E57xx Encoders Annex L: Alarm List Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page iii ST.RE.E10137.3...
Page 4 Preliminary Pages About this Reference Guide This Reference Guide provides instructions and information for the installation and operation of the Voyager E5784 and E5788 HD DSNG Encoder. This Reference Guide should be kept in a safe place for reference for the life of the equipment.
Page 5 Reflex™ is a trademark of TANDBERG Television. Windows NT™ is a trademark of Microsoft Corporation. STREAMS™ is a trademark of TANDBERG Television. NDS™ is a trademark of NDS Limited. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page v ST.RE.E10137.3...
Page 6 This equipment is certified to the EMC requirements detailed in Annex B, Technical Specification. To maintain this certification, only use the leads supplied or if in doubt contact Customer Services. Page vi Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 7: Contact Information
TANDBERG Television and your business. Warranty All TANDBERG Products and Systems are designed and built to the highest standards and are covered under a comprehensive 12 month warranty. Levels of Continuing TANDBERG Television Service Support For stand-alone equipment, then TANDBERG Television BASIC Advantage is the value for money choice for you.
Page 8: Return Of Equipment
Preliminary Pages Technical Training Training Courses TANDBERG Television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. TANDBERG can provide both regularly scheduled courses and training tailored to individual needs. Courses can be run either at your premises or at one of our dedicated training facilities.
Page 9: Table Of Contents
Audio Inputs..........1-9 Audio Channels ..........1-9 MPEG Encoding Modes ......1-10 Dolby Digital (AC-3) Encoding Modes ..1-10 Test Tones..........1-10 Audio Variable Bit-rate........ 1-10 Dolby Digital (AC-3)........1-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 1-1 ST.RE.E10137.3...
Page 10 List of Tables Table 1.1: Build Version ..............1-3 Table 1.2: Equipment Model Descriptions........1-4 Table 1.3: Video Bit-rate Range ........... 1-7 Table 1.4: Front Panel Indicators ..........1-13 Page 1-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 11: Introduction To The Basic Encoder
WARNING… DO NOT REMOVE THE COVERS OF THIS EQUIPMENT. HAZARDOUS VOLTAGES ARE PRESENT WITHIN THIS EQUIPMENT AND MAY BE EXPOSED IF THE COVERS ARE REMOVED. ONLY TANDBERG TELEVISION TRAINED AND APPROVED SERVICE ENGINEERS ARE PERMITTED TO SERVICE THIS EQUIPMENT. CAUTION…...
Page 12: Role Of The Encoder In A System
4:2:2 is only available when software option M2/ESO2/422 and M2/ESO2/HD422 is purchased. Noise reduction is only available when software option M2/ESO2/NR and M2/ESO2/HDNR is purchased. Page 1-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 13: Dsng Systems
4:2:2 is only available in HD in the E5788 Encoder when an HD licence is purchased and in SD when software option M2/ESO2/422 is purchased. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 1-5 ST.RE.E10137.3...
Page 14: Video Encoding Modes
Support for some MP@HL and 422P@HL standard coding modes • Selectable bit-rate operation, <1.5 Mbit/s - 90 Mbit/s (see Table 1.3) • Support for various video picture resolutions (HD and SD) Page 1-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 15: Motion Estimation
2 Mbit/s 2 Mbit/s Noise reduction is only available when software option M2/ESO2/NR or M2/ESO2/HDNR is purchased. The video bit-rate depends on the Multiplexer bit-rate which is set. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 1-7 ST.RE.E10137.3...
Page 16: Coding Resolutions
Display Stored OSD (Only available if the Encoder has an OSD loaded). • Cut to a black screen (HD default) To ensure broadcast quality it is recommended that the studio reference is fed to HYSNC. Page 1-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 17: Audio Encoding
Dolby Digital (AC-3) is only available when software option M2/ESO2/AC3 is purchased. To achieve lip sync in all modes the audio option M2/EOM2/AUDLIN2 must be used. See Annex F, Audio Modes for details of setting up the audio. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 1-9 ST.RE.E10137.3...
Page 18: Mpeg Encoding Modes
The Encoder has three modes for processing VBI lines. NOTE… A maximum of eight VBI lines per field may be extracted. This limit does not apply to Teletext. Page 1-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 19: Vbi In Picture
DVB specification EN300-472. The Encoder can extract up to 18 lines of Teletext from each field of the video frame. VITC: Only timecode is extracted. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 1-11 ST.RE.E10137.3...
Page 20: High Definition (Hd) Closed Captions And Teletext
RS-232/RS-485 remote control port. Alternatively, Local control is implemented through the front panel keypad and display. 1.3.9 Options and Upgrades Options and Upgrades are described in Chapter 3, Options and Upgrades. Page 1-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 21: Guided Tour
I is always at the top (see Figure 1.3). WARNING… THIS IS NOT A MAINS SWITCH AND DOES NOT ISOLATE THE ENCODER FROM THE POWER SUPPLY. On position Stand-by position Figure 1.3: Stand-by Switch Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 1-13 ST.RE.E10137.3...
Page 22: Rear Panel Description
The Encoder provides connectors at the rear panel (see Chapter 2, Installing the Equipment). All, except the power connector, are physically located on the separate modules which comprise the Encoder. Page 1-14 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 23 2.7.2 From the Front Panel Menus ......2-19 2.5.3 Power Supply ..........2-11 List of Figures 2.5.4 Technical Earth........... 2-11 2.5.5 Video Inputs..........2-11 Figure 2.1: Fitting the Encoder into a Rack ........2-5 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-1 ST.RE.E10137.3...
Page 24 Table 2.15: IF Output Connector (Monitor)........2-17 Table 2.16: L-Band In Connector ..........2-17 Table 2.17: L-Band Out (Main) Connector ........2-18 Table 2.18: L-Band Out (Monitor) Connector ......2-18 Page 2-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 25: Introduction
IF THE ENCODER HAS BEEN SUBJECT TO A LIGHTNING STRIKE OR POWER SURGE WHICH HAS STOPPED IT WORKING, DISCONNECT THE POWER IMMEDIATELY. DO NOT REAPPLY POWER UNTIL IT HAS BEEN CHECKED FOR SAFETY. IF IN DOUBT, CONTACT TANDBERG TELEVISION CUSTOMER SERVICES.
Page 26: Fcc
Slide the Encoder onto the chassis supports and affix to the rack by means of an M6 x 18 mm panhead screw in each corner (see Figure 2.1). Do not use this product as a support for any other equipment. Page 2-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 27: Cable Routing
3. The fans contained within this unit are not fitted with a dust/insect filter. Pay particular attention to the environment in which it is to be used. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-5 ST.RE.E10137.3...
Page 28 Cool air in Cool air in (front – via bottom vent) Figure 2.2: Air Path Through the Enclosure NOTE… Cooling arrangements in current models may differ to those shown. Page 2-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 29: Ac Mains Operating Voltage And Earthing
Brown Black If the colours do not correspond with the coloured markings identifying the terminals in a locally supplied plug, proceed as in Table 2.2 (included for reference). Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-7 ST.RE.E10137.3...
Page 30: Protective Earth/Technical Earth
Ensure the correct fuse type and rating has been fitted to both the equipment and the a.c. power cable. Connect the a.c. power lead to the Encoder mains input connector and then to the local mains supply. Page 2-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 31: Signal Connections For The Basic Unit
SDI In Composite Video Option Slot 6 Option Slot 1 L-Band Out L-Band Out L-Band HD SDI Input Monitor Main Figure 2.4: L-Band Rear Panel Component Parts and Connectors Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-9 ST.RE.E10137.3...
Page 32: Connecting Up The Basic Encoder
Do not move or install equipment whilst it is still attached to the mains supply. Ensure ESD precautions are observed whilst interconnecting equipment. NOTE… See Chapter 3 for information relating to Options and Upgrades. Page 2-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 33: Power Supply
Up to four channels of embedded audio can be carried in the serial video stream. These are chosen using the Audio Source and Embedded Src 12 (audio channels 1 and 2) or Embedded Src 34 (audio channels 3 and 4) option menus. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-11 ST.RE.E10137.3...
Page 34: H Sync
There are four XLR female connectors, with the fifth cable being a BNC which provides an AES/EBU 75 Ω digital reference output. Page 2-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 35: Asi Out 1, 2 And 3 Outputs
2.5.8 Control Interfaces Connection Operation of the Encoder from a TANDBERG Television control system is via the Ethernet network running the Simple Network Management Protocol (SNMP) protocol. Connect the ETHERNET connector to the controller (for example, MEM). Local control is implemented through the front panel keypad and display.
Page 36: Ethernet #1 And #2
Alarm (NO) NOTE… NC = Normally Closed, NO = Normally Open, and refers to the relay contacts. Refer to Annex B for details of the relay contact rating. Page 2-14 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 37: Remote Control
Signal Direction Signal Name Not connected Received Data Received Data Transmit Data Transmit Data Not connected Signal Ground Signal Ground Not connected Not connected Not connected Not connected Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-15 ST.RE.E10137.3...
Page 38: Rs-422 Connector
Transmit Clock B Transmit Clock B Not connected NOTE… Signal names are with respect to a DTE in accordance with the RS-422 specification. A is positive and B is negative. Page 2-16 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 39: 2.5.10 Satellite Modulator If Output
L-band signal to be summed with the modulator output. Table 2.16: L-Band In Connector Item Specification 50 Ω SMA Female Connector Type Type Analogue Connector designation L-Band In Pin-outs Centre Signal Screen Ground Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-17 ST.RE.E10137.3...
Page 40: L-Band Out (Main)
3. The power supply has been checked and a good earth provided. 4. The correct fuse type and rating has been fitted to the equipment and, for the a.c. supply version, the a.c. power cable. Page 2-18 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 41: Powering Up
Enter softkey. IP Address ← Left Encoder IP Address : → Right `172.16.248.91’ — Enter Update using softkeys Quit Figure 2.6: Changing the Encoder IP Address Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 2-19 ST.RE.E10137.3...
Page 42 Installing the Equipment BLANK Page 2-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 43 DVB ASI OUT 1 Connector ......3-11 3.10.1 Assembly.............3-22 3.5.3 Stages of Remultiplexing......3-11 3.10.2 Connectors..........3-23 3.5.4 Function of Remultiplexer......3-13 3.5.5 Using the Remultiplexer ......3-14 3.11 M2/EOM2/ATMS45 PDH/DS3 Module ....3-23 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-1 ST.RE.E10137.3...
Page 44 Table 3.20: Out Connector ............3-29 M2/ESO2/525VBIDATA ......3-33 Table 3.21: In Connector............. 3-30 M2/ESO2/DPI..........3-33 Table 3.22: GPI Connector............3-31 M2/ESO2/EthernetData ......3-33 3.16.2 High Definition..........3-33 M2/ESO2/HDNR .........3-33 M2/ESO2/HDVBR........3-33 M2/ESO2/HD422 ........3-33 M2/ESO2/HD-MPASS.........3-33 Page 3-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 45: What's Available
Empty option slots must be fitted with a blanking plate. BISS is implemented according to Tech 3290 March 2000 and BISS-E is implemented according to Tech 3292 April 2001. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-3 ST.RE.E10137.3...
Page 46: Limitations On Number Of Option Modules
The Encoder has a number of hardware and software options (see Table 3.1 and Table 3.2). To see which are fitted/enabled refer to the Build Menu (see Chapter 4, Operating the Equipment Locally, Figure 4.9). Page 3-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 47: Basic Interoperable Scrambling System - Biss (M2/Edcom2/Biss)
Menu (see Chapter 4, Operating the Equipment Locally, Section 4.10.14). BISS is implemented according to Tech 3290 March 2000 and BISS-E is implemented according to Tech 3292 April 2001. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-5 ST.RE.E10137.3...
Page 48: Additional Audio And Linear Pcm Option (M2/Eom2/Audlin2)
The AES/EBU reference signal is provided for backwards compatibility only. When using E57xx Encoders use the reference signal provided by the Base Board. Figure 3.1: Additional Audio and Linear PCM Option (M2/EOM2/AUDLIN2) Page 3-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 49: Audio In Connector
When the Encoder is powered down the digital channel is selected with 110 Ω termination. The digital audio input does not support SPDIF. CAUTION… To ensure EMC compliance, use the audio connector supplied with the Encoder. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-7 ST.RE.E10137.3...
Page 50: Advanced Audio Coding Option (M2/Eom2/Advaud)
Figure 3.2: Advanced Audio Coding Option (M2/EOM2/ADVAUD) The Additional Audio Coding option module comprises Assembly S14048 and Card S13600. See Table 3.1 for the slots that it can be installed in. Page 3-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 51: Aes X Connector
When the Encoder is powered down the digital channel is selected with 110 Ω termination. The digital audio input does not support SPDIF. CAUTION… To ensure EMC compliance, use the audio connector supplied with the Encoder. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-9 ST.RE.E10137.3...
Page 52: Remux Option (M2/Eom2/Remux)
Input Transport Stream 2 DVB ASI IN 2 Input Transport Stream 3 DVB ASI IN 3 Output is disabled DVB ASI OUT 1 Figure 3.3: Remux Option (M2/EOM2/REMUX) Page 3-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 53: Dvb Asi In 1, 2 And 3 Connectors
Encoder services (or streams) can be combined together in the output. Figure 3.4 shows a typical satellite system using one stage of remultiplexing. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-11 ST.RE.E10137.3...
Page 54 IF Output contains 13 services. Contributing Encoder Encoders with Remux Service 11 ASI (x3) ASI (x4) Service 12 Service 10 Service 13 Figure 3.5: Block Diagram – Two Stages of Remultiplexing Page 3-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 55: Function Of Remultiplexer
Audio Host Audio Encoder Rate ASI Driver ASI Output Dual Port Remux Input Output Bit-rate Modulator IF Output Remux QPSK Input Remux Input Figure 3.6: Remultiplexer Block Diagram Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-13 ST.RE.E10137.3...
Page 56: Using The Remultiplexer
NOTE… It is possible to remultiplex any DVB or ATSC compliant transport stream but at the time of publication, only transport streams generated by TANDBERG Television equipment are guaranteed to work when fed to the Remultiplexing module. The equipment will automatically detect the services on these inputs. The list of detected services is displayed in the Setup/Mux Menu.
Page 57: What To Do If Overflow Occurs
To avoid corruption reduce the incoming bit-rate by either removing services, (turn the service Off or remove the ASI input), or reduce the bit-rate of the incoming service. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-15 ST.RE.E10137.3...
Page 58: Smpte 310 (Ssi) And Asi Optical Outputs Option Modules (M2/Eom2/Asi-Opt) And (M2/Eom2/Ssi-Us)
Asynchronous Serial Output 1 ASI OUT 1 40 Mbit/s max Asynchronous Serial Output 2 ASI OUT 2 Figure 3.7: SMPTE 310 (SSI) and ASI Optical Outputs Option Modules (M2/EOM2/ASI-OPT) and (M2/EOM2/SSI-US) Page 3-16 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 59: Smpte 310 1, 2 And 3 Connectors
DO NOT LOOK INTO THE APERTURE. LOOKING INTO THE APERTURE COULD CAUSE DISCOMFORT TO YOUR EYE. NOTE… The Class 1 LED warning is as defined in paragraph 5.2 of EN 60825-1 1994. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-17 ST.RE.E10137.3...
Page 60: Atm Network Interface Option Module (M2/Eom2/Atms155
A BNC, female 75 Ω connector provides a DVB-PI compliant copper connection at a fixed line transmission rate of 270 Mbit/s. ATM is the abbreviation for Asynchronous Transfer Mode. Page 3-18 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 61: 10Baset Ethernet Connector
See Table 3.1 for the slots that it can be installed in. For details of the DVB-ASI Copper Input, DVB-ASI Copper Output and Ethernet Connector refer to Section 3.7.3, Common Connectors on page 3-18. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-19 ST.RE.E10137.3...
Page 62: Multimode Fibre Optic Connector
The module is supplied with a protective sealing cap, which protects the optical components from ingress of dust and foreign bodies. The protective sealing cap should be fitted during transit and whenever the interface is not in use. Page 3-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 63: Oc3 Monomode Physical Interface Module (M2/Eom2/Atms155Sm)
The module is supplied with a protective sealing cap, which protects the optical components from ingress of dust and foreign bodies. The protective sealing cap should be fitted during transit and whenever the interface is not in use. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-21 ST.RE.E10137.3...
Page 64: M2/Eom2/Atms34 Pdh/E3 Module
Input from PDH/E3 B-ISDN Network Output to PDH/E3 B-ISDN Network ATM-PDH-E3 ASI-C Input ASI-C Output DVB ASI–C Local Control ETHERNET Figure 3.10: Rear Panel Connectors (M2/EOM2/ATMS34 ATM PDH/E3 Module) Page 3-22 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 65: 3.10.2 Connectors
There are currently four different ways to transmit ATM cells over DS-3. They are: • C-bit parity ADM • C-bit parity PLCP • M23 ADM • M23 PLCP Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-23 ST.RE.E10137.3...
Page 66: 3.11.2 Connectors
Ethernet Connector refer to Section 3.7.3, Common Connectors on page 3-18. NOTE… Be aware that the BNC connector positions on this module are reversed when compared to the same connectors on the E3 and DS3 modules. Page 3-24 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 67: 3.12.2 Connectors
STS-3c network at a transmission rate of 155.520 Mbit/s. This is a full duplex service. Table 3.16: SDH STM-1/SONET STS-3c Electrical Connector Item Specification Connector type Connector designation ATM-SDM-STM1/E Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-25 ST.RE.E10137.3...
Page 68: Ip Output Card (M2/Eom2/Ip) Ip Card Pro-Mpeg Fec (M2/Eom2/Ip/Profec)
This option sets the parameters and protocol required to send video over 3.13.3 Smallcasting Mode In this mode, the transport stream can be transmitted to four specified IP addresses. Page 3-26 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 69: 3.13.4 Assembly
A 3.5mm socket provides a debug interface. NOTE… This connector is for TANDBERG Television use only. ASI Out A 75 Ω female BNC connector provides an ASI output. NOTE… This connector is not used. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-27 ST.RE.E10137.3...
Page 70: Ethernet Output
Connector Type RJ-45 Connector designation 10/100 BT Pin-out Tx Out (+) Tx Out (-) Rx In (+) Not Connected Not Connected Rx In (-) Not Connected Not Connected Page 3-28 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 71: Interface Card Option (M2/Eom2/G703)
Figure 3.14: G.703 Interface Card Option M2/EOM2/G703 OUT Connector A 75 Ω female BNC connector provides a G.703 transport stream output. Table 3.20: Out Connector Signal Centre Signal Screen Ground Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-29 ST.RE.E10137.3...
Page 72: In Connector
The controlled functions are software assigned. • 2 Contact Closure Outputs which can be either open circuit or connected to the common output. Each output has inverted or non- inverted contacts Page 3-30 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 73: 3.15.2 Assembly
Output 1 NI Input 2 Output 1 Common Input 3 Output 1 I Input 4 Output 2 NI Input 5 Output 2 Common Input 6 Output 2 I Input 7 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-31 ST.RE.E10137.3...
Page 74: Software Options
This purchasable option allows the Encoder to provide MHP timing Events. Contact Customer Services for details. M2/ESO2/DTS This purchasable option allows the Encoder to provide DTS Audio. Contact Customer Services for details. Page 3-32 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 75: M2/Eso2/525Vbidata
M2/ESO2/HD-MPASS This purchasable option upgrades the Encoder to operate in multipass mode in a reflex group. Contact Customer Services for details. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-33 ST.RE.E10137.3...
Page 76 Options and Upgrades BLANK Page 3-34 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 77 DVB ASI OUT 1 Connector ......3-11 3.10.1 Assembly.............3-22 3.5.3 Stages of Remultiplexing......3-11 3.10.2 Connectors..........3-23 3.5.4 Function of Remultiplexer......3-13 3.5.5 Using the Remultiplexer ......3-14 3.11 M2/EOM2/ATMS45 PDH/DS3 Module ....3-23 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-1 ST.RE.E10137.3...
Page 78: Modules (M2/Eom2/Asi-Opt) And (M2/Eom2/Ssi-Us)
Table 3.20: Out Connector ............3-29 M2/ESO2/525VBIDATA ......3-33 Table 3.21: In Connector............. 3-30 M2/ESO2/DPI..........3-33 Table 3.22: GPI Connector............3-31 M2/ESO2/EthernetData ......3-33 3.16.2 High Definition..........3-33 M2/ESO2/HDNR .........3-33 M2/ESO2/HDVBR........3-33 M2/ESO2/HD422 ........3-33 M2/ESO2/HD-MPASS.........3-33 Page 3-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 79: What's Available
Empty option slots must be fitted with a blanking plate. BISS is implemented according to Tech 3290 March 2000 and BISS-E is implemented according to Tech 3292 April 2001. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-3 ST.RE.E10137.3...
Page 80: Limitations On Number Of Option Modules
The Encoder has a number of hardware and software options (see Table 3.1 and Table 3.2). To see which are fitted/enabled refer to the Build Menu (see Chapter 4, Operating the Equipment Locally, Figure 4.9). Page 3-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 81: Basic Interoperable Scrambling System - Biss (M2/Edcom2/Biss)
Menu (see Chapter 4, Operating the Equipment Locally, Section 4.10.14). BISS is implemented according to Tech 3290 March 2000 and BISS-E is implemented according to Tech 3292 April 2001. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-5 ST.RE.E10137.3...
Page 82: Additional Audio And Linear Pcm Option (M2/Eom2/Audlin2)
The AES/EBU reference signal is provided for backwards compatibility only. When using E57xx Encoders use the reference signal provided by the Base Board. Figure 3.1: Additional Audio and Linear PCM Option (M2/EOM2/AUDLIN2) Page 3-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 83: Audio In Connector
When the Encoder is powered down the digital channel is selected with 110 Ω termination. The digital audio input does not support SPDIF. CAUTION… To ensure EMC compliance, use the audio connector supplied with the Encoder. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-7 ST.RE.E10137.3...
Page 84: Advanced Audio Coding Option (M2/Eom2/Advaud)
Figure 3.2: Advanced Audio Coding Option (M2/EOM2/ADVAUD) The Additional Audio Coding option module comprises Assembly S14048 and Card S13600. See Table 3.1 for the slots that it can be installed in. Page 3-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 85: Aes X Connector
When the Encoder is powered down the digital channel is selected with 110 Ω termination. The digital audio input does not support SPDIF. CAUTION… To ensure EMC compliance, use the audio connector supplied with the Encoder. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-9 ST.RE.E10137.3...
Page 86: Remux Option (M2/Eom2/Remux)
Input Transport Stream 2 DVB ASI IN 2 Input Transport Stream 3 DVB ASI IN 3 Output is disabled DVB ASI OUT 1 Figure 3.3: Remux Option (M2/EOM2/REMUX) Page 3-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 87: Dvb Asi In 1, 2 And 3 Connectors
Encoder services (or streams) can be combined together in the output. Figure 3.4 shows a typical satellite system using one stage of remultiplexing. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-11 ST.RE.E10137.3...
Page 88 IF Output contains 13 services. Contributing Encoder Encoders with Remux Service 11 ASI (x3) ASI (x4) Service 12 Service 10 Service 13 Figure 3.5: Block Diagram – Two Stages of Remultiplexing Page 3-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 89: Function Of Remultiplexer
Audio Host Audio Encoder Rate ASI Driver ASI Output Dual Port Remux Input Output Bit-rate Modulator IF Output Remux QPSK Input Remux Input Figure 3.6: Remultiplexer Block Diagram Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-13 ST.RE.E10137.3...
Page 90: Using The Remultiplexer
NOTE… It is possible to remultiplex any DVB or ATSC compliant transport stream but at the time of publication, only transport streams generated by TANDBERG Television equipment are guaranteed to work when fed to the Remultiplexing module. The equipment will automatically detect the services on these inputs. The list of detected services is displayed in the Setup/Mux Menu.
Page 91: What To Do If Overflow Occurs
To avoid corruption reduce the incoming bit-rate by either removing services, (turn the service Off or remove the ASI input), or reduce the bit-rate of the incoming service. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-15 ST.RE.E10137.3...
Page 92: Smpte 310 (Ssi) And Asi Optical Outputs Option Modules (M2/Eom2/Asi-Opt) And (M2/Eom2/Ssi-Us)
Asynchronous Serial Output 1 ASI OUT 1 40 Mbit/s max Asynchronous Serial Output 2 ASI OUT 2 Figure 3.7: SMPTE 310 (SSI) and ASI Optical Outputs Option Modules (M2/EOM2/ASI-OPT) and (M2/EOM2/SSI-US) Page 3-16 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 93: Smpte 310 1, 2 And 3 Connectors
DO NOT LOOK INTO THE APERTURE. LOOKING INTO THE APERTURE COULD CAUSE DISCOMFORT TO YOUR EYE. NOTE… The Class 1 LED warning is as defined in paragraph 5.2 of EN 60825-1 1994. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-17 ST.RE.E10137.3...
Page 94: Atm Network Interface Option Module (M2/Eom2/Atms155
A BNC, female 75 Ω connector provides a DVB-PI compliant copper connection at a fixed line transmission rate of 270 Mbit/s. ATM is the abbreviation for Asynchronous Transfer Mode. Page 3-18 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 95: 10Baset Ethernet Connector
See Table 3.1 for the slots that it can be installed in. For details of the DVB-ASI Copper Input, DVB-ASI Copper Output and Ethernet Connector refer to Section 3.7.3, Common Connectors on page 3-18. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-19 ST.RE.E10137.3...
Page 96: Multimode Fibre Optic Connector
The module is supplied with a protective sealing cap, which protects the optical components from ingress of dust and foreign bodies. The protective sealing cap should be fitted during transit and whenever the interface is not in use. Page 3-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 97: Oc3 Monomode Physical Interface Module (M2/Eom2/Atms155Sm)
The module is supplied with a protective sealing cap, which protects the optical components from ingress of dust and foreign bodies. The protective sealing cap should be fitted during transit and whenever the interface is not in use. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-21 ST.RE.E10137.3...
Page 98: M2/Eom2/Atms34 Pdh/E3 Module
Input from PDH/E3 B-ISDN Network Output to PDH/E3 B-ISDN Network ATM-PDH-E3 ASI-C Input ASI-C Output DVB ASI–C Local Control ETHERNET Figure 3.10: Rear Panel Connectors (M2/EOM2/ATMS34 ATM PDH/E3 Module) Page 3-22 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 99: 3.10.2 Connectors
There are currently four different ways to transmit ATM cells over DS-3. They are: • C-bit parity ADM • C-bit parity PLCP • M23 ADM • M23 PLCP Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-23 ST.RE.E10137.3...
Page 100: 3.11.2 Connectors
Ethernet Connector refer to Section 3.7.3, Common Connectors on page 3-18. NOTE… Be aware that the BNC connector positions on this module are reversed when compared to the same connectors on the E3 and DS3 modules. Page 3-24 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 101: 3.12.2 Connectors
STS-3c network at a transmission rate of 155.520 Mbit/s. This is a full duplex service. Table 3.16: SDH STM-1/SONET STS-3c Electrical Connector Item Specification Connector type Connector designation ATM-SDM-STM1/E Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-25 ST.RE.E10137.3...
Page 102: Ip Output Card (M2/Eom2/Ip) Ip Card Pro-Mpeg Fec (M2/Eom2/Ip/Profec)
This option sets the parameters and protocol required to send video over 3.13.3 Smallcasting Mode In this mode, the transport stream can be transmitted to four specified IP addresses. Page 3-26 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 103: 3.13.4 Assembly
A 3.5mm socket provides a debug interface. NOTE… This connector is for TANDBERG Television use only. ASI Out A 75 Ω female BNC connector provides an ASI output. NOTE… This connector is not used. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-27 ST.RE.E10137.3...
Page 104: Ethernet Output
Connector Type RJ-45 Connector designation 10/100 BT Pin-out Tx Out (+) Tx Out (-) Rx In (+) Not Connected Not Connected Rx In (-) Not Connected Not Connected Page 3-28 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 105: Interface Card Option (M2/Eom2/G703)
Figure 3.14: G.703 Interface Card Option M2/EOM2/G703 OUT Connector A 75 Ω female BNC connector provides a G.703 transport stream output. Table 3.20: Out Connector Signal Centre Signal Screen Ground Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-29 ST.RE.E10137.3...
Page 106: In Connector
The controlled functions are software assigned. • 2 Contact Closure Outputs which can be either open circuit or connected to the common output. Each output has inverted or non- inverted contacts Page 3-30 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 107: 3.15.2 Assembly
Output 1 NI Input 2 Output 1 Common Input 3 Output 1 I Input 4 Output 2 NI Input 5 Output 2 Common Input 6 Output 2 I Input 7 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-31 ST.RE.E10137.3...
Page 108: Software Options
This purchasable option allows the Encoder to provide MHP timing Events. Contact Customer Services for details. M2/ESO2/DTS This purchasable option allows the Encoder to provide DTS Audio. Contact Customer Services for details. Page 3-32 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 109: M2/Eso2/525Vbidata
M2/ESO2/HD-MPASS This purchasable option upgrades the Encoder to operate in multipass mode in a reflex group. Contact Customer Services for details. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 3-33 ST.RE.E10137.3...
Page 110 Options and Upgrades BLANK Page 3-34 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 111 4.5.4 Remote Control Menu.........4-25 PSIP Min PID..........4-20 Overview .............4-25 PSIP Max PID..........4-20 IP Address Option........4-26 Data n min/max .......... 4-20 MAC Address Option ........4-26 Major Channel Option......... 4-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-1 ST.RE.E10137.3...
Page 112 Overview .............4-32 Indicated Bit-Rate Option (SD Only)... 4-51 Host Service 1..........4-32 Copyright Option......... 4-51 4.6 Video Menu .............4-34 Original Option..........4-51 4.6.1 Introduction ..........4-34 Scene Cut Detection........4-51 Page 4-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 113 Software Release Option......4-70 SMPTE 302M Standard Option ....4-80 4.7.3 Audio (Dolby Digital (AC-3) Menu) ..... 4-70 Channel Option ...........4-80 Source Option..........4-70 Embedded Source Option......4-81 Coding Standard Option ......4-70 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-3 ST.RE.E10137.3...
Page 114 Guard Interval Option ....... 4-102 OP on Digital I/P Loss.........4-91 Carriers Options ........4-102 Temporal Noise Shaping......4-91 Other Frequency Option......4-103 ADTS CRC..........4-91 4.9.6 Descriptor Type = Cable......4-103 Copyright Option .........4-91 Page 4-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 115 Tx Bandwidth Factor Option ..... 4-111 4.10.7 Clock ............4-120 Tx Bandwidth Option ........ 4-111 4.10.8 PCR PID Option........4-121 Bit-rate (188) Option ......... 4-111 4.10.9 FPGA Firmware ........4-121 Bit-rate (204) Option ......... 4-111 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-5 ST.RE.E10137.3...
Page 116 4.13.4 DPI Initiated by DVS 525......4-143 Srce Clk Tolerance Option......4-132 4.13.5 Menu Structure......... 4-143 CDV Tolerance Option......4-132 4.14 Errors Menu ............4-145 TS Asi Output Option ........4-133 Page 4-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 117 Table 4.60: OP Digital Loss Options ........... 4-69 Table 4.3: Remux Input n Mode Options........4-19 Table 4.61: Source Options............4-70 Table 4.4: SI Level Options ............4-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-7 ST.RE.E10137.3...
Page 118 Table 4.174: Cell Mode Options ..........4-135 Table 4.117: Guard Interval Options ......... 4-102 Table 4.175: Host Bit-rate Options ..........4-136 Table 4.118: Carriers Options ........... 4-103 Table 4.176: PID Remap Options..........4-136 Page 4-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 119 Table 4.181: PMT PID Options..........4-140 Table 4.188: Teletext Options............ 4-142 Table 4.182: PCR PID Options..........4-141 Table 4.189: DPI Options (DPI Mode= GPI SCTE 35)....4-144 Table 4.183: Video Options ............4-141 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-9 ST.RE.E10137.3...
Page 120 Operating the Equipment Locally BLANK Page 4-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 121: Operating The Equipment Locally
Figure 4.1: Input Monitor Pressing the More softkey displays the Summary Screen (see Section 4.2.2, Summary Screen). Pressing the A/V softkey displays the A(udio)/V(ideo) Menu (see Section 4.2.3, Line Up Menu. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-11 ST.RE.E10137.3...
Page 122: Summary Screen
NTSC-M can be selected (29.97 Hz only). 4.2.5 Keyboard Lock The softkeys can be locked out to prevent inadvertent operation (see the key icon in Figure 4.3). Key icon Figure 4.3: Keyboard Lock Page 4-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 123: Navigating The Display Screens
All keys are cyclic, displaying their assigned characters in sequence. In certain options only letters or numbers may be available. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-13 ST.RE.E10137.3...
Page 124: How To Use The Functions Associated With Softkeys
A black diagonal cross enclosed by a white circle ( ) means that the Encoder is under remote control and the user does not have access to change that parameter. Page 4-14 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 125: Display Screens
All menus generally conform to the following format. Some of the menus provide access to sub-menus. A clear circle indicates no further access and is for information only. A black circle indicates further menus or options. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-15 ST.RE.E10137.3...
Page 126 Screen, see the Config — Fail Relay Menu — Alarm Relay — Alarm LED — Buzzer — Quit Figure 4.6: Menu Hierarchy – Summary Screen and Advanced Menus Page 4-16 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 127: Summary Screen And Advanced Menus
This menu permits the selection of system information. Any option with a clear circle next to it cannot be accessed and changed. It is for status information only. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-17 ST.RE.E10137.3...
Page 128: Figure 4.7: Menu Hierarchy – Setup/System Menu
— Upgrade Encoder is set to DVB Subtitle. — Software Release — Fan Control Shaded options are showing status and cannot be changed. Figure 4.7: Menu Hierarchy – Setup/System Menu Page 4-18 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 129: Service Info Menu (Syntax = Atsc)
PSI and PSIP. For further information refer to ATSC Standard Doc A/65 Program and System Information Protocol for Terrestrial Broadcast and Cable - Annex D. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-19 ST.RE.E10137.3...
Page 130: Si Level Option
Major Channel Option This is associated with the field major_channel_number and is used to group all channels that are to be identified as belonging to a particular broadcast corporation. Page 4-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 131: Minor Channel Option
System Time Table (STT). Changes can be made in the Time and Date Menu. DVB Subtitles NOTE… This option is only available when Remux Input n Mode is set to DVB Subt. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-21 ST.RE.E10137.3...
Page 132: Service Info Menu (Syntax = Dvb)
Service Name Option This option allows the service name to be changed. The information is included in the SDT. Syntax Option This enables the syntax to be specified. Page 4-22 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 133: Remux Input N In Mode
PSI/PSIP to be externally generated. There must be no PID clashes (between other inputs or the locally generated streams) as PID clashes are not resolved nor detected by the Encoder. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-23 ST.RE.E10137.3...
Page 134: Network Id Option
Decoders (e.g. early Alteias) used the AC-3 descriptor for identifying Dolby Digital AC-3 streams. NOTE… This is only available when the syntax is set to DVB. Page 4-24 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 135: Logical Chan Desc Option
Ethernet using either SNMP, or a web browser. The Remote Control Menu provides options for configuring these interfaces. See Figure 4.7 for the Remote Control Menu structure. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-25 ST.RE.E10137.3...
Page 136: Ip Address Option
This option is only available from the front panel. This option allows the web browser password to be set. To prevent unauthorised knowledge of the password it cannot be read back from the Encoder. Page 4-26 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 137: Sntp Server Option
(i.e. respond to command as described in the ‘Remote Control Protocol (RCP)’. The serial menu system available via this serial port is similar to Telnet (i.e. front panel level menu available via user name ‘general’, ‘password’.) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-27 ST.RE.E10137.3...
Page 138: General Menu
This number is used to set the GPS_UTC_Offset field in the ATSC STT table. Temperature Option The Temperature option indicates the current internal temperature. Page 4-28 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 139: Screen Saver Option
This shows the serial number of the box, which is in the range of 0 to 65535. Send this number to TANDBERG Customer Services and they will return a software licence key to enter via the front panel to enable the features.
Page 140: Time And Date
Encoder has to provide this. To ensure correct lip sync when working with linear or pre-encoded audio, the option card M2/EOM2/AUDLIN2 should be used. Page 4-30 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 141: Action On Pid Error Option
Reset On Download Option (Status Only) The option is status only. The Encoder automatically reboots following a download, keeping the current configuration. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-31 ST.RE.E10137.3...
Page 142: Reset Encoder Option
This option sets the service ID for the service, which is used to uniquely identify it in the PAT, PMT, SDT, EIT and NIT. The valid range is 0 to 65535. Page 4-32 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 143 If the elementary stream has already selected as part of another service, selecting it as part of this service will automatically remove it from the other service. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-33 ST.RE.E10137.3...
Page 144: Video Menu
Mainly used for test purposes. HD-SDI HD Serial digital video input on HD SDI IN connector. Color Bars Colour bar test pattern. Black Black internal test pattern. Monitor Test Pattern Page 4-34 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 145 Only shown if the logo has previously been downloaded into the Encoder. Shaded options are showing status and cannot be changed. Figure 4.8: Menu Hierarchy – Setup/Video Menu (SD Mode) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-35 ST.RE.E10137.3...
Page 146: Figure 4.9: Menu Hierarchy – Setup/Video Menu (Hd Mode)
Logo only shown if the logo has previously been downloaded into the Encoder. CC options only shown if Closed Captions enabled. Shaded options are showing status and cannot be changed. Figure 4.9: Menu Hierarchy – Setup/Video Menu (HD Mode) Page 4-36 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 147: Input Source Select (Sd Only)
The Encoder adjusts the input setting with regards to the actual input. Any change is reflected back as status on the Encoder interfaces. The normal input selection is read-only. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-37 ST.RE.E10137.3...
Page 148: Input Horiz Res (Hd Only)
This option gives the choice of what is displayed on the television screen in the event of losing video input. NOTE… Black and ASI off are the only options available in HD mode. Page 4-38 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 149: Predictive Processing (Sd Only)
Refer to Application Note ST.AN.1094, Video Noise Reduction and Compression for more information. Noise reduction is only available when software option M2/ESO2/NR or M2/ESO2/HDNR is purchased. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-39 ST.RE.E10137.3...
Page 150: Max Still Period Option (Sd Only)
This sets the default for the 625 Line standard. Table 4.29 : Default 625 Options Selected Option Description PAL-B/G/H/I PAL-D PAL-M (Jaimaca) PAL-M Default 525 [Analog] This sets the default for the 625 Line standard. Page 4-40 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 151: I/P Monitor Refresh Option
Time Code Option This option indicates the time given by the Vertical Interval Time Code (VITC) or generated by the Encoder. It is for status only and cannot be changed. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-41 ST.RE.E10137.3...
Page 152: Video Filter/Process (Sd Only)
Changing compression causes a change to GOP structure and length. Picture quality may decrease with reduced delay. 4:2:2 is not available unless the M2/ESO2/422 or M2/ESO2/HD422 (E5788) software option is enabled. Page 4-42 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 153 Seamless 6 mode is typically used with 4:2:2 statistical multiplexing and a low B . Actual minimum and maximum depend on the video standard and resolution. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-43 ST.RE.E10137.3...
Page 154: Bit-Rate Option
The spare capacity these modes provide is ideal for opportunistic data insertion. The VBR licence M2/ESO2/HDVBR is needed with this option. Page 4-44 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 155: Vbr Mode (Sd Only) Option
Encoder generates a fixed constant bit-rate set by the Bit-rate option. When changed to On (Variable) the Encoder enters its stand-alone VBR Mode. The VBR licence M2/ESO2/VBR is needed with this option. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-45 ST.RE.E10137.3...
Page 156: Delay Option
This option gives both horizontal and vertical resolution. The first number indicates the horizontal resolution and the second the vertical resolution. For example, 720x576 gives a horizontal resolution of 720 and a vertical resolution 576. Page 4-46 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 157: Aspect Ratio Option
Active Format Descriptor (AFD) uses three bits of video index to define the video format. This information is encoded into user data and can then be used by a Decoder for wide-screen switching. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-47 ST.RE.E10137.3...
Page 158: Gop Structure Option
Present but no Video Index from Video Video Index data Index (This could be 0) GOP Structure Option This option enables the GOP Structure to be set. Page 4-48 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 159: Gop Length Option
Long GOP structures can improve video encoding performance, particularly at low bit-rates. However, it can lead to compression artefacts being visible on scene cuts, and a periodic build-up and removal of noise at the I-frame rate. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-49 ST.RE.E10137.3...
Page 160: Adaptive Gop
29.97 frames per second NTSC rate. This enables the Encoder to increase the video compression by only including a flag in the transport stream to represent a repeated field (when detected), rather than compressing the repeated fields. Page 4-50 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 161: Concatenation Option (Sd Only)
If set to 'Max Value' the maximum possible bit-rate for the profile and encoding mode is signalled. This is the way all previous generations of TANDBERG Encoders have operated. If set to 'Actual Value', and the encoding mode is not a seamless mode, then the bit-rate signalled is the actual video bit-rate set on the Encoder.
Page 162: Insert Vbv Delay Option (Sd Only)
Digital TV Group (DTG) format. It is now also registered as a DVB standard (ETSI TR 101 154). When switched off, no AFD is present. The Page 4-52 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 163: Vertical Blanking Interval (Vbi)/Userdata Menu
VITC on PES Option (SD only) Extraction of VITC data from VBI lines as shown in VBI - Line ‘n’ Options on Page 4-56. Enabling this option will disable VBI on PID. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-53 ST.RE.E10137.3...
Page 164 This enables or disables the extraction of VPS (Video Programming System) data from line 16 of the video input. 4:2:2 is only available when software option M2/ESO2/422 is purchased. Page 4-54 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 165 However, a maximum of eight VBI lines can be processed per field (this does not include Teletext lines). Refer to Table 4.46 for the options available for a frame rate of 25 Hz. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-55 ST.RE.E10137.3...
Page 166 This option is used to insert a time code into userdata as defined by SMPTE 328. Only the time code section of SMPTE 328 is implemented, along with appropriate headers. This option has the following selections: On/Off. Page 4-56 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 167 For compatibility with some older Receivers the start of coded video may need to begin at line 22. Contact Customer Services for details. Figure 4.10: VBI Structure Implemented by TANDBERG for 525-line Systems (SD Only) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-57 ST.RE.E10137.3...
Page 168 ETS 300 294 is the specification which describes WSS. EN 300 472 is the specification associated with System B Teletext (World System Teletext). Figure 4.11: VBI Structure Implemented by TANDBERG for 625-line Systems (SD Only) Page 4-58 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder...
Page 169: Vbi Menu
Table 4.47: VBI in Picture Options Selected Option Description VBI is coded as active video. Off (Bit-rate too low) Insufficient bit-rate. 4:2:2 is only available when software option M2/ESO2/422 is purchased. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-59 ST.RE.E10137.3...
Page 170 Field 1 Captions This option sets the appropriate descriptors in the PSIP information. It allows the number of CC services, from the source, contained in Field 1 to be entered. Page 4-60 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 171 This option is used to insert a time code into userdata as defined by SMPTE 328. Only the time code section of SMPTE 328 is implemented, along with appropriate headers. This option has the following selections: On/Off. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-61 ST.RE.E10137.3...
Page 172: Audio Menu
Audio passes through the SRC for all input sources i.e. Embedded, Digital, Analogue (though not really relevant for analogue). Page 4-62 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 173: Figure 4.12: Menu Hierarchy – Setup/Audio Menu
Auto Lip Sync is Status only when Use Minimum Delay = On cannot be changed. — PCR on Audio PID Dolby E Pass–thru only. — Hardware Release — Software Release Figure 4.12: Menu Hierarchy – Setup/Audio Menu Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-63 ST.RE.E10137.3...
Page 174: Input Level L Option
This option sets the audio coding mode. If the current audio bit-rate is outside the bit-rate range supported by the new coding mode, the bit-rate is automatically changed to the lowest value within the supported range. Page 4-64 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 175: Vps Controls Coding Mode
Only available if VPS Controls Coding Mode is set to On. This displays the hex value extracted from the VPS. If it has not been able to extract any information, it displays 0xFF. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-65 ST.RE.E10137.3...
Page 176: Vps Stereo Mode
If either of these options is selected, the coding mode is forced to this when Dual channel is signalled in bits 1 and 2 (i.e. Bit1/2 is 1 1). Single Page 4-66 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 177: Auto Lip Sync Option
The clip levels available depend on the hardware issue of the Encoder. To ensure correct lip sync when working with linear or pre-encoded audio, use the option card M2/EOM2/AUDLIN2. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-67...
Page 178: Impedance Option
Off the bit-stream will be signalled as a copy of an original bit-stream. Embedded Source Option This option defines the embedded source. Select HD-SDI or SD-SDI. Page 4-68 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 179: Embedded 1-2 Did Option
The ASI output of the Encoder is turned off Hardware Release Option This option indicates the hardware version of this audio encode channel. It is for status only and cannot be changed. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-69 ST.RE.E10137.3...
Page 180: Software Release Option
SRC for all input sources i.e. Embedded, Digital, Analogue (though not really relevant for analogue). Audio Alignment Setting this to Aligned ensures each PES packet contains an integral number of audio frames (which is required by some set-top boxes). Page 4-70 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 181: Lip Sync Adjustment
Dolby Digital Settings 32 kbit/s 48 kbit/s 56 kbit/s 64 kbit/s 80 kbit/s 96 kbit/s 112 kbit/s 128 kbit/s 160 kbit/s 192 kbit/s 224 kbit/s 256 kbit/s 320 kbit/s Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-71 ST.RE.E10137.3...
Page 182: Coding Mode Option
Valid Input Range Description Min: Lip Sync Offset in milliseconds. Max: To ensure correct lip sync when working with linear or pre-encoded audio, use the option card M2/EOM2/AUDLIN2. Page 4-72 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 183: Audio Delay Option
600 Ω or 20 kΩ. Language Option This enables the language of the audio channel to be set. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-73 ST.RE.E10137.3...
Page 184: Bit Stream Mode Option
Dolby Surround The bit-stream is conveying a Dolby Surround encoded program. Production Info Option This option indicates whether the Mixing Level and Room Type parameters exist within the bit-stream. Page 4-74 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 185: Mixing Level Option
The dynamic range compression profile determines the characteristic curve of the dynamic range compression algorithm (each profile has its own boost, null-band and cut parameters). Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-75 ST.RE.E10137.3...
Page 186: Rf Protection Option
This option is used to enable or disable a low-pass filter in the audio input which has a cut-off near the specified bandwidth of the audio channel. Embedded Source Option This option defines the embedded source. Select HD-SDI or SD-SDI. Page 4-76 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 187: Embedded 1-2 Did Option
Valid PES stream containing silence No PID No Audio PES stream (though stream is still refernced in SI) No ASI O/P The ASI output of the Encoder is turned off Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-77 ST.RE.E10137.3...
Page 188: Hardware Release Option
SRC for all input sources i.e. Embedded, Digital, Analogue (though not really relevant for analogue). Audio Alignment (Dolby E only) When checked, Auto Lip Sync is forced On, the delay can be ‘nudged’ using the Lip Sync Adjustment option. Page 4-78 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 189: Lip Sync Adjustment
If this option is set to ON, the Auto Lip Sync and Audio Delay options are unavailable. To ensure correct lip sync when working with linear or pre-encoded audio, use the option card M2/EOM2/AUDLIN2. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-79 ST.RE.E10137.3...
Page 190: Lip Sync Offset Option
This option is only available if the coding standard is Dolby E Pass-thru. It controls the value written to the channel identification field in the (SMPTE 302M) AES3 data elementary stream header. Page 4-80 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 191: Embedded 1-2 Did Option
This may be necessary if an audio only service is being generated. The default setting is Off. OP Digital Loss This option controls behaviour digital audio is not locked. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-81 ST.RE.E10137.3...
Page 192: Hardware Release Option
Pre-encoded DTS audio coding standard. See Annex F, Audio Modes, for information when using this mode. Linear PCM (Direct) Linear PCM audio coding standard. See Annex F, Audio Modes, for information when using this Page 4-82 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 193: Audio Alignment
This indicates the input level of the left audio channel. It is for status only and cannot be changed. Input Level R Option This indicates the input level of the right audio channel. It is for status only and cannot be changed. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-83 ST.RE.E10137.3...
Page 194: Coding Mode Option
Shows the actual audio delay. It is for status only and cannot be changed. To ensure correct lip sync when working with linear or pre-encoded audio, use the option card M2/EOM2/AUDLIN2. Page 4-84 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 195: Clip Level Option
Receiver are not using the same version of SMPTE 302M. This option allows the Encoder to be configured to work in either the 1998 or the 2000 version of SMPTE 302M. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-85 ST.RE.E10137.3...
Page 196: Channel Option
PID to less than 32, but in the event of a PID clash the Encoder’s internal checking algorithm will not resolve the conflict. Component Tag Option This item defines the optional component tag to be assigned to this audio stream. Page 4-86 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 197: Pcr On Audio Pid Option
The asterisk is turned on and off. There are over forty languages to choose from in addition to two User Defined Language options where the User can input and use their own three-letter codes. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-87 ST.RE.E10137.3...
Page 198: Advanced Audio Coding
This option sets the audio bit-rate of this audio channel. Table 4.98: Bit-rate Options Available Settings 64 kbit/s 80 kbit/s 96 kbit/s 112 kbit/s 128 kbit/s 160 kbit/s 192 kbit/s 224 kbit/s 256 kbit/s Page 4-88 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 199: Coding Mode Option
Multi-channel: 320, 384 kbit/s Mono: 64, 80, 96, 128, 192 kbit/s When a multi-channel coding mode is selected, the channels are presented to the module inputs as follows: Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-89 ST.RE.E10137.3...
Page 200: Auto Lip Sync Option
See the text underneath Table 4.16 on page 4-30 for use of this facility. Use Minimum Delay This sets the lowest possible audio delay. If this option is set to ON, the Auto Lip Sync and Audio Delay options are unavailable. Page 4-90 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 201: Language Or Language Left/Right Option
SDI Embedded 3 and SDI Embedded 4. If this is set to 1024, then the default DID will be used. Refer to Annex F, Audio Modes for information about DIDs. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-91 ST.RE.E10137.3...
Page 202: Level [L] Option
This indicates the input level of the right audio channel. It is for status only and cannot be changed. Component Tag Option This item defines the optional component tag to be assigned to this audio stream. Page 4-92 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 203: Data Menu
Figure 4.14: Menu Hierarchy – Setup/Data Menu 4.8.2 Data A - RS232 Menu Encoding Option This option enables the RS-232 asynchronous data channel to be switched On or Off. Table 4.104 shows the modes. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-93 ST.RE.E10137.3...
Page 204: Baud Rate Option
This item defines the optional component tag to be assigned to this data stream. Buffer Data Option Send immediately: Whenever data is available at the RS232 port it is sent in the output transport stream. Page 4-94 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 205: Delay Option
Settings cycle from 56 to 1792 in steps of 56 then from 64 to RS-422 synchronous data 2048 in steps of 64, then back to 56 channel bit-rate. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-95 ST.RE.E10137.3...
Page 206: Rs422 Pid Option
NOTES… Delivery of packets is not guaranteed. The maximum data-rate is 100 kbit/s. It is only possible to turn this option on if RS232 data is turned off. Page 4-96 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 207: Port Number
If the Output Format option = ASI then the following menu option is Delivery Descriptor, otherwise it is the menu associated with the output format selected, i.e. satellite modulator, OFDM modulator or IP Output. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-97 ST.RE.E10137.3...
Page 208: Delivery Descriptor Menu
The type of delivery descriptor selected affects the remaining Terrestrial Descriptor type set to Terrestrial. options shown on the Delivery None Descriptor Menu. Cable Descriptor type set to Cable. Page 4-98 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 209 Show Config Status Differences NOTE… Refer to Annex K for details of Pro MPEG FEC for IP Streaming in E57xx Encoders. Figure 4.15: Menu Hierarchy – Setup/Output Menu Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-99 ST.RE.E10137.3...
Page 210: Descriptor Type = Terrestrial
This option is status only unless Manual has been selected in the Band Plan option. CCIR is now know as International Telecommunications Union-Radiocommunications Study Groups. Organisation that co-ordinated TV standards and programme interchange among the Eastern–block countries of Europe. Page 4-100 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 211: Bandwidth Option
Terrestrial transmission is hierarchical, and the α value = 1. Alpha=1 Terrestrial transmission is hierarchical, and the α value = 2. Alpha=2 Terrestrial transmission is hierarchical, and the α value = 4. Alpha=4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-101 ST.RE.E10137.3...
Page 212: Fec (Hp) And Fec (Lp) Options
Access the Carriers option from the Delivery Descriptor Menu. This enables the transmission mode (i.e. number of carriers in an OFDM frame) used by the terrestrial transmitter to be specified. Page 4-102 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 213: Other Frequency Option
FEC rate used by the cable channel to be specified. Table 4.121: FEC (Outer) Options Selected Option Description No outer FEC coding Cable channel does not use outer FEC. RS(204/188) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-103 ST.RE.E10137.3...
Page 214: Fec (Inner) Option
Access the FEC (Inner) option from the Delivery Descriptor Menu. This screen enables the inner FEC rate used by the satellite transponder to be specified. See FEC (Inner) Option, page 4-104 for further details. Page 4-104 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 215: Orbital Position Option
Circular - Right Satellite transponder uses circular right polarisation. 4.9.8 Output Format = Satellite Modulator (IF Output) TS Input Source This option determines the source of the transport stream. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-105 ST.RE.E10137.3...
Page 216: If Output Option
Satellite Modulator uses 16QAM modulation. NOTE… The following software options must be purchased to enable the different modulation types; M2/ESO2/LSYM for BPSK, M2/ESO2/SM38PSK for 8PSK, M2/ESO2/SM316QAM for 16QAM. Page 4-106 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 217: Symbol Rate Option
Access the Tx Bandwidth Factor option from the Satellite Modulator Menu. This option is used to calculate the Tx Bandwidth based upon the Symbol Rate. Bandwidth = Factor x Symbol Rate Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-107 ST.RE.E10137.3...
Page 218: Tx Bandwidth Option
Access the Sat Deliv Freq option from the Satellite Modulator Menu. Table 4.137: Sat Deliv Freq Options Valid Input Range Description Min: 0.0000 GHz Max: 999.9999 GHz Step Size: 0.0001 GHz Page 4-108 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 219: Sat Orb Pos Option
BB PCB Revision Option • BB Mod Status Option • BB Serial No. Option • BB S/W Release Option • BB CPLD F/W Release Option • BB DSP F/W Release Option Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-109 ST.RE.E10137.3...
Page 220: Output Format = Satellite Modulator
Access the Modulation option from the Satellite Modulator Menu. This enables the modulation to be switched On or Off. Mod Type Option Refer to Mod Type Option on page 4-106 for details. Page 4-110 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 221: Symbol Rate Option
Sat Deliv Freq Option Refer to Sat Deliv Freq Option on page 4-108 for details. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-111 ST.RE.E10137.3...
Page 222: Sat Orb Pos Option
Own IP Address Option Access the Own IP Address option from the IP Streamer Menu. This is the local IP address associated with the 100 Mbit/s Ethernet video output interface. Page 4-112 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 223: Network Mask Option
Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-113...
Page 224: Destination X Udp Port Option
DVB service over a G.703 network. See Figure 4.15 for the menu structure. NOTE… The G.703 card is only compatible with TANDBERG Television’s MkII G.703 Input card. PDH Rate Option This option sets the overall G.703 Interface Module’s line rate at either the E3 (34.368 Mbit/s) or DS3 rate (44.736 Mbit/s).
Page 225: Reed-Solomon Option
This option cannot be altered and should always be displayed as Tx. This indicates that the G.703 card portion of the G.703 Interface Module is set to Tx mode. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-115 ST.RE.E10137.3...
Page 226: Mode Option
G.703 card portion of the G.703 Interface Module is set to MKII mode. Reset Option This option is for TANDBERG use only and it is a method to reset the G.703 card of the G.703 Interface Module. MPEG Input Row Option This option cannot be altered and should always be displayed as A.
Page 227: 4.10.3 Mux Output, With Remux Card
• Host Bit-rate Option on page 4-136 • Remux Module menu – see Section 4.12.3, Remux Module Menu • Host and Incoming Services – Section 4.12.4, 1.Service/2.Service Menu Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-117 ST.RE.E10137.3...
Page 228 This option is not available from Build version 2.2. enabled. Only available when the Remux card is fitted and Shaded options are showing status and cannot be changed. Figure 4.16: Menu Hierarchy – Setup/Mux Menu (DVB) Page 4-118 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 229 — ECM (CA) PID — Audio (type of audio) — Data (type of data) Shaded options are showing status and cannot be changed. Figure 4.17: Menu Hierarchy – Setup/Mux Menu (ATSC) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-119 ST.RE.E10137.3...
Page 230: 4.10.4 Packet Length Option
This option indicates the origin of the clock. It must be set to a video or external source before attempting to change the clock value or it will default to Local Oscillator. This option enables the Clock to be set. Page 4-120 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 231: 4.10.8 Pcr Pid Option
This option enables RAS1 security scrambling of the Encoder transmission to be switched on or off. BISS is implemented according to Tech 3290 March 2000 and BISS-E is implemented according to Tech 3292 April 2001. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-121 ST.RE.E10137.3...
Page 232: Sng Key (Ras1) Option
Description Encoder output is not scrambled. RAS (Fixed 1) Encoder output is scrambled using the fixed RAS key assigned by TANDBERG TV, and preprogrammed into the Encoder. RAS (Fixed 2) Encoder output is scrambled using the fixed second RAS key assigned by TANDBERG TV, and preprogrammed into the Encoder.
Page 233: Scramble Option
Encoder into a Session Word used to encrypt and decrypt the transport stream. NOTE… Take precautions to avoid general knowledge of the Encrypted Session Word. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-123 ST.RE.E10137.3...
Page 234: Biss-E Injected Id Option
Selected Option Description Connect Sets up SVC or PVC connection to the other end of the network. Not Connected No connection to the other end of the network. Page 4-124 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 235 Only shown when Enable SVC PMP= True. Length Errors Crc Errors Shaded options are showing status and cannot be changed. Unknown Cells Figure 4.18: Menu Hierarchy – Setup/ATM Menu Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-125 ST.RE.E10137.3...
Page 236: 4.11.3 Delete Connection Option
Enter a number to view the details of that specific connection ID. They are status only and cannot be changed. • Name • Connection Status • Termination Status • VC Type • Media • • • Direction • Page 4-126 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 237: 4.11.6 Add Profile Menu
A PVC is a circuit, equivalent to a dedicated leased line, yet over some form of packet switched network. A PVC is set up once, usually through the management system of the network supporting it, and continues to exist until it is removed, again via the management system. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-127 ST.RE.E10137.3...
Page 238: Vpi Option
ATM cell is to travel. ATM Adaptation Layer – the standards layer that allows multiple applications to have data converted to and from the ATM cell. Page 4-128 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 239: 4.11.7 Delete Profile Menu
4.11.10 Delete Authorisation Menu The Delete Authorisation Menu lists the current Authorisations. Select an authorisation by pressing the associated softkey. Change to ‘Delete’ and press the Enter softkey. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-129 ST.RE.E10137.3...
Page 240: 4.11.11 Edit Authorisation Option
ATM network operator. This only needs to be specified if the ATM network does not support Integrated Layer Management Interface (ILMI) which normally sets this prefix automatically Internet Protocol. Page 4-130 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 241: Def Uni Version Option
Selected Option Description Encoder Default setting. External ASI BNC input. Own ATM Address only appears in the General menu when the Enable SVC PMP option is set to TRUE. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-131 ST.RE.E10137.3...
Page 242: Aal5 Pcr Aware Option
Long pauses may occur as the recipient waits for the reply. Cell Delay Variation – a component of cell transfer delay, induced by buffering and cell scheduling. Page 4-132 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 243: Ts Asi Output Option
Bit-rate • Bit-rate (Min) • Bit-rate (Max) • Lost Cells • Misinserted Cells • Corrected Packets • Uncorrected Packets • Length Errors • Crc Errors • Unknown Cells Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-133 ST.RE.E10137.3...
Page 244: 4.11.16 Physical Menu
Table 4.173: Tx Clock Source Options Selected Option Description Recovered Rx clock Use when connected to a switch. Local Clock Use when connected directly to another ATM card. Page 4-134 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 245: Cell Mode Option
Table 4.174: Cell Mode Options Selected Option Description Idle Unassigned Default setting. Interface Option The Interface option is for status only and indicates the type of physical layer interface. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-135 ST.RE.E10137.3...
Page 246: Remux Menu
Remux input before it is locked-down. PID Remap Status This option only appears in Lock PID Mapping mode. It indicates whether the power-up delay has expired and lock-down has occurred. Page 4-136 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 247: Packet Length Option
The maximum input bit-rate allowed on the Remux Module ASI inputs is 50 Mbit/s. If the input bit-rate exceeds 86 Mbit/s it will be incorrectly reported as a lower rate. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-137...
Page 248: 4.12.4 1.Service/2.Service Menu
NOTE… This option is only shown on an incoming Service menu (2-13.Service Menu). This option indicates the input service name. It is status only and cannot be changed. Page 4-138 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 249: Name Out Option
This option is only shown in ATSC mode. This option enables the major channel to be specified. Minor Channel Option NOTE… This option is only shown in ATSC mode. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-139 ST.RE.E10137.3...
Page 250: Logical Channel Option
PCR PID Option NOTE… This option is status only for the Host Encoder but can be changed for incoming services. This option shows the Program Clock Reference Packet Identifier. Page 4-140 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 251: Video Option
Build version 2.2.0. This option is used for entering or updating the VBI PID. Table 4.185: VBI PID Options Selected Option Description Min: Max: 8190 (1FFEh) Step Size: 1 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-141 ST.RE.E10137.3...
Page 252: Audio (Type Of Audio) Option
This option is status only for the Host Encoder but can be changed for incoming services. This option is used for entering or updating Teletext PIDs. Table 4.188: Teletext Options Selected Option Description Min: Max: 8190 (1FFEh) Step Size: 1 Page 4-142 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 253: Digital Programme Insertion (Dpi) Menu
— Nbr Return Msg — Off — Splice Duration — Fixed Delay — Splice ID Increment Mode Figure 4.19: Menu Hierarchy – Digital Programme Insertion DPI Menu (GPI Initiated) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-143 ST.RE.E10137.3...
Page 254 Users can enter a constant milli-second offset here to get sub-second accuracy. GPI Input Pin Physical pin on GPI connector to be monitored. GPI OutofNet Whether an open or close will trigger Out of Network. Polarity Page 4-144 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 255: Errors Menu
Press the softkey next to a message. As the key is pressed the status of the message changes. Restore Defaults Access the Restore Defaults option from the Error Masks Menu. This sets alarm, fail and error messages to the factory defaults. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-145 ST.RE.E10137.3...
Page 256: Masked Active Errors
GUI but doesn't generate an error. Off and Masked are two of the same thing. 4.15 Diagnostics Menu See Chapter 6, Preventive Maintenance and Fault-finding for information about the Diagnostics Menu. Page 4-146 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 257: Configs Menu
16 user configuration locations (Load Active Config). It can be edited at any time and also stored back as one of the user configurations (Store Active Config). Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-147 ST.RE.E10137.3...
Page 258: User Configurations
The letter R when shown to the left of the config number, indicates that the configuration is read-only (write-protected). Any configuration that is write-protected will be displayed as read-only if attempting to overwrite it. Page 4-148 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 259: Load Active Config Option
This enables the 16 user configurations to be stored in the backup, and may be password protected. NOTE… The 16 backup configurations are stored immediately the Store Configs in Backup softkey is pressed. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 4-149 ST.RE.E10137.3...
Page 260: Factory Hd Defaults Option
Operating the Equipment Locally: Configs Menu 4.16.8 Factory HD Defaults Option This option enables the 16 user configurations to be overwritten by the factory default settings. Page 4-150 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 261 5.3 Web Browser Interface Options ........ 5-6 Figure 5.5: Proxy Settings Dialog Box........... 5-5 5.4 Fault Reporting............5-8 Figure 5.6: TFTP Protocol for Cloning a File......... 5-9 5.5 Cloning a File ............5-9 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 5-1 ST.RE.E10137.3...
Page 262 Web Browser Interface BLANK Page 5-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 263: Introduction
2. In the General tab click Settings (see Figure 5.1). Settings Figure 5.1: Internet Options Dialog Box 3. This opens the Settings dialog box (see Figure 5.2). Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 5-3 ST.RE.E10137.3...
Page 264 Encoder, bypassing the proxy server. Click the Connections tab (see Figure 5.3). LAN Settings Figure 5.3: Connections Tab Page 5-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 265 Figure 5.4: Local Area Network (LAN) Settings Dialog Box 7. Click Advanced to open the Proxy Settings dialog box (see Figure 5.5). Type the IP address of the Encoder Figure 5.5: Proxy Settings Dialog Box Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 5-5 ST.RE.E10137.3...
Page 266: Web Browser Interface Options
A definition of management items for some network component that can be accessed by a network manager. A MIB includes the names of objects it contains and the type of information retained. Page 5-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 267 Masked, Alarm, Fail or Ignore. Modules - allows you to set the alarm error masks for each individual module to Masked, Alarm, Fail or Ignore. Fault Reporting – see Section 5.4. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 5-7 ST.RE.E10137.3...
Page 268: Fault Reporting
3. Select the directory where you want to save the files and click Save. 4. Send to the files to TANDBERG Television. 5. Also, send a clone file of the Encoder configuration. See Section 5.5, Cloning a File for details. Page 5-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 269: Cloning A File
A particularly useful feature of the Encoder is the ability to extract a clone file. This can be sent to TANDBERG Television and used to configure other Encoders to exactly the same specification. It is very useful when trying to reproduce a fault and also for restoring a machine after repair.
Page 270 Web Browser Interface BLANK Page 5-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 271 Table 6.4: Fans Not Working/Overheating........6-11 6.5 Fault-finding .............. 6-7 6.5.1 Fault-finding Philosophy ....... 6-7 6.5.2 Preliminary Checks........6-7 6.5.3 AC User Accessible Fuse Replacement..6-8 6.5.4 Video Fault-finding........6-9 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 6-1 ST.RE.E10137.3...
Page 272 Preventive Maintenance and Fault-finding BLANK Page 6-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 273: Introduction
4. If the product does not operate normally by following the operating instructions 5. If the product has been dropped or the case has been damaged 6. When the product exhibits a distinct change in performance Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 6-3 ST.RE.E10137.3...
Page 274: Replacement Parts
There is a customer service centre open round the clock, every day of the year, in your time zone. TANDBERG’s years of design and support experience enable it to offer a range of service options that will meet your needs at a price that makes sense.
Page 275: Errors And Diagnostics Menus - When To Use
The Diagnostics Menu is selected from the Advanced Menu by pressing the Diagnostics softkey. This menu (see Figure 6.2) has a selection of diagnostic tests which allow the operator to test the individual component parts of the equipment. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 6-5 ST.RE.E10137.3...
Page 276: Lcd Display Test
Press the Buzzer softkey to access the option which immediately causes a buzzer to sound. Press any key (except the Quit softkey) to turn the buzzer off. Press the Quit softkey to return to the menu. Page 6-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 277: Fault-Finding
WARNING… DO NOT REMOVE THE COVERS OF THIS EQUIPMENT. HAZARDOUS VOLTAGES ARE PRESENT WITHIN THIS EQUIPMENT AND MAY BE EXPOSED IF THE COVERS ARE REMOVED. ONLY TANDBERG TELEVISION TRAINED AND APPROVED SERVICE ENGINEERS ARE PERMITTED TO SERVICE THIS EQUIPMENT. CAUTION…...
Page 278: Ac User Accessible Fuse Replacement
Fuse Carrier Figure 6.3: Orientation of Fuse Carrier If the replacement fuse also blows, do not continue. Disconnect the equipment and contact Customer Services for advice. Page 6-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 279: Video Fault-Finding
Licence M2/ESO2/NR or M2/ESO2/HDNR is needed for this feature. 4:2:2 is only available when software option M2/ESO2/422 is purchased. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 6-9 ST.RE.E10137.3...
Page 280: Field/Frame Pictures (Sd Only)
DO NOT ATTEMPT TO SERVICE THE POWER SUPPLY UNIT AS OPENING OR REMOVING COVERS MAY EXPOSE DANGEROUS VOLTAGES OR OTHER HAZARDS. REFER ALL SERVICING TO SERVICE PERSONNEL WHO HAVE BEEN AUTHORISED BY TANDBERG TELEVISION. Use the following techniques to fault-find the Encoder according to the observed symptom(s) when a power supply failure is suspected.
Page 281: Fan(S) Not Working/Overheating
Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies and/or environmental restrictions differ throughout the world. Contact your local jurisdiction or local authority for specific advice on disposal. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page 6-11 ST.RE.E10137.3...
Page 282: Lithium Batteries
Dallas DS9034PCX Power Cap Lithium battery. This cell is not a USA Environmental Protection Agency listed hazardous waste. It is fully encapsulated and should not be tampered with. Page 6-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 283 Annex A Glossary The following list covers most of the abbreviations, acronyms and terms as used in TANDBERG Television Limited Manuals, User and Reference Guides. All terms may not be included in this Reference Guide. µm Micrometre (former name - micron): a unit of length equal to one millionth (10 ) of a metre.
Page 284 (RS) coding followed by convolutional coding to add extra bits to the transmitted signal. This allows a large number of errors at the receive end to be corrected by convolutional (Viterbi) decoding followed by RS decoding. Page A-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 285 EP-DVB group and approved by the ITU. Specifies modulation, error correction, etc. (see EN 300 421 for satellite, EN 300 429 for cable and EN 300 744 for terrestrial). DVB SI Digital Video Broadcasting Service Information. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page A-3 ST.RE.E10137.3...
Page 286 Group of Pictures: MPEG video compression works more effectively by processing a number of video frames as a block. The TANDBERG Television Encoder normally uses a 12 frame GOP; every twelfth frame is an I frame. General Purpose Interface. A TANDBERGTV card used to control various specific functions of TTV encoders using a contact closure input.
Page 287 Low Noise Block Down-Converter: The component of a subscriber satellite transmission receiving dish which amplifies the incoming signal and down-converts it to a suitable frequency to input to the IRD (typically 950 MHz - 1600 MHz). Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page A-5 ST.RE.E10137.3...
Page 288 MCPC Multiple Channels Per Carrier. Multiplex Element Manager: A GUI based control system, part of the range of TANDBERG Television compression system control element products. The evolution 5000 MEM holds a model of the system hardware. Using this model, it controls the individual system elements to configure the output multiplexes from the incoming elementary streams.
Page 289 A picture / frame produced using forward prediction. It contains predictions from either previous I frames or previous P frames. The P frame is used as a reference for future P or B frames. Parts per million. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page A-7 ST.RE.E10137.3...
Page 290 Random Access Memory: A volatile storage device for digital data. Data may be written to, or read from, the device as often as required. When power is removed, the data it contains is lost. Remote Authorization System: A TANDBERG TV proprietary public-key encryption system used to prevent unauthorized viewing of a TV programme or programmes.
Page 291 A set of packetised elementary data streams and SI streams, which may comprise more than one programme, but with common synchronisation and error protection. The data structure is defined in ISO/IEC 13818-1 [1] and is the basis of the ETSI Digital Video Broadcasting standards. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page A-9 ST.RE.E10137.3...
Page 292 A type of programmable Integrated Circuit. Y (Luminance) Defines the brightness of a particular point on a TV line. The only signal required for black and white pictures. Page A-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 293: Technical Specification
Multimode Fibre Optic Connector ....B-25 B.4.2 Local Control ..........B-15 Monomode Fibre Optic Connector..... B-25 B.4.3 Alarm ............B-16 M2/EOM2/ATMS34 PDH/E3 Connector ..B-26 B.4.4 Remote Control ..........B-16 M2/EOM2ATMS45 PDH/DS3 Connector... B-27 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-1 ST.RE.E10137.3...
Page 294 Table B.48: Ethernet Port (IP Output Card)......... B-28 Table B.20: L-BAND OUT MONITOR Specification....B-14 Table B.49: GPI Connector ............B-29 Table B.21: Reference Frequency Output Specification ..... B-15 Page B-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 295: Inputs
SMPTE 292M Bit Serial Digital Interface for High Definition Television Systems Cable length 100 m, maximum 800 mV pk-pk nominal ±10% Input level Return loss >15 dB, 1.5 GHz Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-3 ST.RE.E10137.3...
Page 296: H Sync
The Encoder settings for the PAL/NTSC video performance figures are shown in Table B.4. NOTE… The PAL and NTSC video performance figures are measured when the Encoder is connected to a calibrated Receiver. Page B-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 297: Pal Video Performance Figures
Multiburst VITS line 18 Frequency response 1.0 MHz ±0.2 dB 2.0 MHz ±0.2 dB 4.0 MHz ±0.2 dB 4.8 MHz ±0.5 dB 5.8 MHz - 0 to –2.5 dB Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-5 ST.RE.E10137.3...
Page 298: Ntsc Video Performance Figures
15 625 15 625 15 625 Aspect ratio 4 / 3 4 / 3 4 / 3 4 / 3 4 / 3 4 / 3 Video band (MHz) Page B-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 299: Video Coding Resolutions
600 Ω or 20 kΩ (selectable). 20 kΩ = default Input impedance Input standard (digital) AES/EBU digital 110 Ω Termination Sampling rate 32/48 kHz (selectable) Input rate 32, 44.1, 48 kHz Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-7 ST.RE.E10137.3...
Page 300 Tolerance for Left and Right Legs for Channel (A) and Channel (B) Test Level 1 kHz @ 0 dB ± 0.2 dB Sweep 20 Hz - 20 kHz @ -20 dB Page B-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 301: Embedded Audio (Via Sdi
Audio embedded on the serial digital interface can also be extracted. Up to four stereo pairs of audio can be extracted from the SDI. The Encoder can extract two DIDs at once, giving four stereo pairs. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-9 ST.RE.E10137.3...
Page 302: Embedded Audio (Via Hd Sdi
Connector type BNC female connector Input standard SMPTE 299M MPEG-1 Audio Encoding Bit-rates Table B.13: MPEG-1 Audio Encoding Bit-rates Bit-rate Single Dual Stereo Joint Stereo (kbit/s) Channel Mono Mono Page B-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 303: Dolby Digital Audio Encoding Bit-Rates
Connector designation: L-BAND IN 50 Ω Input impedance: Gain to L-BAND OUT MAIN 0 dB ±2 dB output: +5 dBm max Input power: Return loss: >14 dB, 950-1750 MHz Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-11 ST.RE.E10137.3...
Page 304: Test Tones
Carrier frequency: 50-180 MHz, tuneable in 1 kHz steps < ±1 kHz (all causes over 10 years) Carrier frequency error: Carrier ON/OFF ratio: >60 dB Carrier suppression: >40 dB Page B-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 305: L-Band Outputs
8PSK and 16QAM as per EN 301 210 (DVB-DSNG) (HOM option) FEC rate: 1/2, 2/3, 3/4, 5/6 and 7/8 with QPSK 2/3, 5/6 and 8/9 with 8PSK 3/4, and 7/8 with 16QAM Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-13 ST.RE.E10137.3...
Page 306 Connector type: Connector designation: L-BAND OUT MONITOR 75 Ω Output impedance: −30 dB nominal relative to main L-band output power Output power: Return loss: >10 dB, 950-1750 MHz Page B-14 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 307: Reference Frequency Output
Connector designation ETHERNET#1 and ETHERNET#2 Connector type 8-way RJ-45 socket, 10BaseT (ISO 882/3) B.4.2 Local Control Local control is by means of the front panel keypad and LCD display. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-15 ST.RE.E10137.3...
Page 308: Alarm
ITU-T V.24/V.28 (RS-232D) asynchronous serial data Connector designation RS-232 DATA Connector type 9-way D-type female Supported baud rates 1200, 2400, 4800, 9600, 19200, 38400 baud Control mechanism XON/XOFF Time-stamp Not supported Page B-16 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 309: Rs-422 Data
56 kbit/s from 56 kbit/s to 1792 kbit/s (selectable) Time-stamp Not supported Operation modes Bit-pipe - Transport packet alignment and byte alignment relative to the incoming bit-stream are arbitrary. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-17 ST.RE.E10137.3...
Page 310: Ac Power Supply
88.9 mm chassis Width 442.5 mm excluding fixing brackets Overall width 482.6 mm including fixing brackets Depth 545 mm excluding rear connector clearance Approximate weight 11.5 kg (25.3 lbs) Page B-18 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 311: Environmental Conditions
In addition, the equipment has been designed to meet the following: UL 60950 Safety of information technology equipment. The version of the standards shown is that applicable at the time of manufacture. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-19 ST.RE.E10137.3...
Page 312: Emc
The EMC tests were performed with the Technical Earth attached, and configured using recommended cables (see Table B.31). Applies only to models of the Encoder using mains (ac) power sources. Page B-20 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 313: Ce Marking
The C-Tick mark was first affixed to this product in 2004. B.10 Cable Types The signal cable types (or similar) in Table B.31 are those recommended by TANDBERG Television in order to maintain product EMC compliance. Table B.31: Suitable Signal Cable Types Signal Type Connector...
Page 314: Option Modules
DVB A010 rev 1 (Asynchronous Serial Interface) 75 Ω terminator must be fitted when this interface is not in use. Byte mode and single packet burst mode only. Page B-22 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 315: Leds
Item Specification Red LED Output disabled Output enabled Green LED Output not in use Flash (1:3 mark:space) 188 byte packets output Flash (3:1 mark:space) 204 byte packets output Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-23 ST.RE.E10137.3...
Page 316: M2/Eom2/Atms155
Connector designation DVB ASI 75 Ω Connector Impedance Packet Size 188 / 204 bytes Data coding 8B 10B Data rate 0.5 Mbit/s to 60 Mbit/s Channel rate 270 Mbit/s Page B-24 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 317: 10Baset Ethernet Connector
2000 metres Monomode Fibre Optic Connector WARNING… LASER: CLASS I LASER PRODUCT. NOTE… The Class 1 Laser warning is as defined in paragraph 5.2 of EN 60825-1 1994. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-25 ST.RE.E10137.3...
Page 318: M2/Eom2/Atms34 Pdh/E3 Connector
ATM Direct Cell Mapping ITU-T G.804 PLCP Mapping ETSI T/NA(91) and T/NA(91)18 Supported Frame Modes ITU-T G.751 and ITU-T G.832. Transit Timing Source Recovered Clock or Local Clock Page B-26 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 319: M2/Eom2Atms45 Pdh/Ds3 Connector
ATM Direct Cell Mapping ITU-T G.804 PLCP Mapping ETSI T/NA(91) and T/NA(91)18 Supported Frame Modes ITU-T G.751 and ITU-T G.832. Transmit Timing Source Recovered Clock or Local Clock Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-27 ST.RE.E10137.3...
Page 320 Table B.48: Ethernet Port (IP Output Card) Item Specification Safety Status: SELV Connector Type: 8-way RJ-45 Connector Designation: 10/100 BT Signal Type: 10/100BaseT Ethernet (IEEE 802.3/802.3u) Transport Stream Rate: 1.5 – 80 Mbit/s Page B-28 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 321 0: Pulled low to between 0.8 V and 0.0 V Limit over-voltage, under-voltage and excess current. Input function Application-specific, tailored by software. Contacts are debounced as required. Open-circuit or connected to common output pin. Output Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page B-29 ST.RE.E10137.3...
Page 322 Technical Specification BLANK Page B-30 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 323: Language Abbreviations
Ndebele (North) English Norwegian Estonian Oriya Finnish Persian French Polish Fulani Portugese Gaelic (Scots) Punjabi German Romanian Greek Russian Gujarati Serbo-Croat Hausa Slovak Hindi Somali Hungarian Spanish Swahili Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page C-1 ST.RE.E10137.3...
Page 324 Language 1 or 2 entry in the menu. Once this has been carried out, the code appears against the User Defined 1 or 2 options and it is these entries that are used for language code insertion. Page C-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 325 D.7 Using the OSD Loader..........D-9 D.7.1 Start-up............D-9 D.7.2 Download an .osd File ........D-10 D.7.3 Show and Hide Regions ......D-12 D.7.4 Multiple Regions .........D-12 D.7.5 Region Interference ........D-12 D.8 Fault-finding ............D-13 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page D-1 ST.RE.E10137.3...
Page 326 Creating and Downloading a Logo BLANK Page D-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 327: Introduction
To overlay the material with a logo, the logo must first be downloaded into the equipment using the Ethernet TFTP protocol. Once this has been done the logo can be enabled or disabled. Contact TANDBERG Television for further details. Summary of Features Up to 13 logos can be overlaid onto the active video.
Page 328 OK will open the .zip file, see Figure D.3. Clicking on option Save this file to disk will allow the user to install the files on their local drive and then open the .zip file as in Figure D.3. Page D-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 329: Creating A Logo Using Osd Creator
To create a logo (.osd) file: 1. Load a Bitmap (.bmp) file. 2. Add transparency in the desired areas. 3. Downsample to the desired size. 4. Save as an .osd file. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page D-5 ST.RE.E10137.3...
Page 330: Loading A .Bmp File
(T) value and is displayed in the bottom right status panel. The transparency component also has a range of 0 to 255, where 0 is fully transparent and 255 is fully opaque. Page D-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 331: Adding Transparency Manually
Create the key file using a drawing package. Colour the active area white, and the inactive area black. Save as a .bmp file. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page D-7 ST.RE.E10137.3...
Page 332: Editing The Palette
The file may also be saved in .bmp format, but this file will not contain transparency information. Page D-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 333: Downloading A Logo Using Osd Loader
Control. To test the connection, click the Remove All button (you will be prompted for confirmation – Remove all OSD Regions Yes/No). The communications box (at the top of the screen) should read Transfer Completed OK. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page D-9 ST.RE.E10137.3...
Page 334: Download An .Osd File
If the Auto Store box is left unchecked, the downloaded logo will be stored in volatile memory and will be lost when power is removed from the Encoder. Page D-10 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 335 Field Line 720 Pixels Digital Active Picture Lines 702 Pixels Analogue Active Picture OSD Loader Co-ordinates (852,517) Figure D.7: 525 Line, OSD Co-ordinates in Active Picture (SD Example) Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page D-11 ST.RE.E10137.3...
Page 336: Show And Hide Regions
Regions are Shown, only one actually appears in the video stream. The application warns if this is the case. When one of the Regions is Hidden, the other may be Shown as normal. Page D-12 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 337: Fault-Finding
Auto Show off, then click Show when display is required. • To move the current Region, reposition the white cursor, check that the OSD File box has the correct image, and click Download. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page D-13 ST.RE.E10137.3...
Page 338 Creating and Downloading a Logo BLANK Page D-14 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 339 Table E.2: Europe VHF ..............E-4 Table E.14: USA................E-8 Table E.3: EuropeCATV ..............E-4 Table E.15: CCIR................E-8 Table E.4: Italy................E-4 Table E.5: Morocco ...............E-4 Table E.6: New Zealand ..............E-5 Table E.7: China................E-5 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page E-1 ST.RE.E10137.3...
Page 340 Band Plans BLANK Page E-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 341 198.500 627.500 767.500 205.500 634.500 774.500 212.500 641.500 781.500 219.500 648.500 788.500 226.500 655.500 795.500 523.500 662.500 802.500 529.500 669.500 809.500 536.500 676.500 816.500 543.500 683.500 550.500 690.500 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page E-3 ST.RE.E10137.3...
Page 342 84.500 212.500 177.500 219.500 186.000 226.500 Table E.5: Morocco Centre Centre Channel Frequency Channel Frequency in MHz in MHz 165.500 197.500 173.500 205.500 181.500 M 10 213.500 189.500 Page E-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 343 R IV 88.000 210.000 96.000 R XI 218.000 R VI 178.000 R XII 226.000 Organisation that co-ordinated TV standards and programme interchange among the Eastern–block countries of Europe. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page E-5 ST.RE.E10137.3...
Page 344 194.000 234.000 202.000 (12) 242.000 210.000 250.180 Table E.11: French Overseas PIA Centre Centre Channel Frequency Channel Frequency in MHz in MHz 178.000 202.000 186.000 210.000 194.000 218.000 Page E-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 345 761.000 J 11 213.000 563.000 665.000 767.000 J 12 219.000 569.000 671.000 773.000 473.000 575.000 677.000 479.000 581.000 683.000 485.000 587.000 689.000 491.000 593.000 695.000 497.000 599.000 701.000 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page E-7 ST.RE.E10137.3...
Page 346 690.000 826.000 562.000 698.000 834.000 570.000 706.000 842.000 578.000 714.000 850.000 586.000 722.000 858.000 594.000 730.000 602.000 738.000 CCIR is now know as International Telecommunications Union-Radiocommunications Study Groups. Page E-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 347 Figure F.2: Digital Audio Modes ............ F-3 Figure F.3: Embedded Audio and Stereo Pairs......F-5 F.3 Embedded Audio on the SDI........F-4 F.4 Detail of Encoder Operation........F-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page F-1 ST.RE.E10137.3...
Page 348 Audio Modes BLANK Page F-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 349: Analogue Audio
Lock Dolby (AC-3) Encoder to AES/EBU reference from Encoder. Independent of Encoder clock source. Independent of Encoder clock source. Figure F.2: Digital Audio Modes Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page F-3 ST.RE.E10137.3...
Page 350: Embedded Audio On The Sdi
The default DID for embedded audio 3-4 is (SD) 1FDh or (HD) 0x1E6 (Group 2). The DIDs are located in ancillary packets in the data stream. NOTE… Default DIDs are selected when a DID value ≥1024 is set. Page F-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 351 15-way D-type Connector Base Card Audio Audio option module (M2/EOM2/AUDLIN2) is required if more than two channels of audio require processing. Figure F.3: Embedded Audio and Stereo Pairs Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page F-5 ST.RE.E10137.3...
Page 352 Audio Modes BLANK Page F-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 353 Calibration intervals depend on the requirements of the particular composite video specification in force. Please contact TANDBERG Television Customer Services for advice. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page G-1 ST.RE.E10137.3...
Page 354 Accuracy of Frequency Sources BLANK Page G-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 355 Annex H Use of Remux Card in ATSC Contents H.1 Remux Card In ATSC With Internal PSIP....H-3 H.2 Remux Card In ATSC With External PSIP....H-3 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page H-1 ST.RE.E10137.3...
Page 356 Use of Remux Card in ATSC BLANK Page H-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 357 Service Info level of ‘On (Ext. PSIP)’. All PIDS between the maximum and minimum are then mapped directly to the output. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page H-3 ST.RE.E10137.3...
Page 358 If the External PSIP input port is changed, the Encoder may fail to correctly map the PIDs on the new port. This can be resolved by rebooting the Encoder. Page H-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 359 Annex I EDH Capability for E57xx Encoders (SD Only) Contents EDH Capability for E57xx Encoders ......I-3 List of Tables Table I.1: EDH Capability Matrix for E57xx Encoders....I-3 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page I-1 ST.RE.E10137.3...
Page 360 EDH Capability for E57xx Encoders (SD Only) BLANK Page I-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 361 CRCs. In this case the Encoder reports the wrong type of errors, which would make fault-finding very confusing for an operator trying to find a fault in the SDI chain. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page I-3 ST.RE.E10137.3...
Page 362 EDH Capability for E57xx Encoders (SD Only) BLANK Page I-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 363 J.5 Examples of Complex Setups........J-7 J.5.1 Example 1 - Everything on One ASI Input..J-7 J.5.2 Example 2 – PSIP and data on different inputs ............J-7 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page J-1 ST.RE.E10137.3...
Page 364 Setting of the Remux Card for Data/PSIP and DVB-Subtitles Input BLANK Page J-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 365: Setting The Remux Card Inputs
The subtitling type for the elementary stream. DVB-Subt. Tag # The DVB component tag for the elementary stream. Comp. page ID # The composition page ID for the elementary stream. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page J-3 ST.RE.E10137.3...
Page 366: The Setting Sequence
4. The Encoder will not reference any data streams in its internally generated PSI. If this is required, switch internal PSI off by setting SI Level to Off CAUTION… It is the user’s responsibility to supply PSI on a Remux input. Page J-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 367: The Setting Sequence
3. The set of the allowed PID values ranges from 2 to 8190. 4. The mapping of the PSI/PSIP elementary streams does not take place until ‘SI Level’ is configured. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page J-5...
Page 368: The Setting Sequence
Remux input # in mode. All that is required is to set the appropriate input in the menu. NOTE… If the Encoder is not behaving as expected, a complete re-setup can be done by following the sequence in Para J.4.1. Page J-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 369: Examples Of Complex Setups
The Remux card input number 1 is used for PSI/PSIP data, number 2 and 3 are both used for other data. NOTE… This was not possible on Encoder builds prior to 3.8.0. Assume the following PID map: Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page J-7 ST.RE.E10137.3...
Page 370 9. Set the SI Level to Off (Ext.PSIP/PSI). CAUTION… In this example, the pid values of port-1 and port-2 are partially overlapped. Care must take to avoid any conflict. Page J-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 371 Nbr of Rows (D) Option ........K-4 K.2.3 Pro-MPEG FEC Constraints......K-4 K.2.4 Recommendations for use of Pro-MPEG FEC ..............K-5 Overview............K-5 Column-Only Mode Performance ....K-5 Row and Column Mode Performance ..K-5 Size of the Matrix..........K-5 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page K-1 ST.RE.E10137.3...
Page 372 Pro-MPEG FEC Support for IP Streaming in E57xx Encoders BLANK Page K-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 373: Introduction
Numbers are arranged in a rectangle of dimensions D * L. The Payload of the FEC packet generated is the ExOR of the row/column it protects. CoLumns (L) Figure K.1: Columns and Rows Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page K-3 ST.RE.E10137.3...
Page 374: Configuring Pro-Mpeg Fec
Best case is 20 rows = (1/20) + 1 = 5% Row and Column Overheads: Overhead = D + L + (D * L) (D * L) Worst case is 4x4 = (4+4+16) / 16 = 50% Page K-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 375: Overview
However using a large matrix means that the latency to decode the transport stream is increased. Using a small matrix will reduce the latency of the system but will obviously significantly increase the overhead. Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page K-5 ST.RE.E10137.3...
Page 376 Pro-MPEG FEC Support for IP Streaming in E57xx Encoders BLANK Page K-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 377: Alarm List
General 00000026 Invalid PMT PID The selected PID value is out of range. Alarm General 00000027 Duplicate PCR PID The selected PID value clashes with another. Alarm General Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page L-1 ST.RE.E10137.3...
Page 378 EDH Full Field Error on the video (SDI) input. Masked Video Source Unknown Error 00000126 EDH Full Field Internal Error on the video (SDI) input. Alarm Video Source Page L-2 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 379 Each field of a video frame has a different time code. This Alarm VBI/Userdata each field prevents the Splice Point insertion from working correctly. 00000176 Serial Closed Serial interface errors. Alarm VBI/Userdata Captions Data Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page L-3 ST.RE.E10137.3...
Page 380 Config Update The audio module is not responding correctly to the requested Alarm Audio A config. 00000284 Incorrect Parameters One or more parameters are incorrect. Alarm Audio A Page L-4 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 381 Too many errors on the digital audio input. Alarm Audio B 00000336 Mux FIFO Overflow Error on the internal Mux input. The audio channel will be reset. Alarm Audio B Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page L-5 ST.RE.E10137.3...
Page 382 No space left in the mux FIFO. Alarm Data A - RS232 01000400 Comms Error "Not set in normal operation. For use with MEM controller, to force Alarm Data B - RS422 Page L-6 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...
Page 383 IP Streamer XXXXXXX4 Packets Discarded Error reported by the option module. Alarm IP Streamer XXXXXXX9 E4 Comms Sequence Error reported by the E4 Module. Alarm Video Encoder Number Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder Page L-7 ST.RE.E10137.3...
Page 384 Alarm List Page L-8 Reference Guide: Voyager E5784 and E5788 HD DSNG Encoder ST.RE.E10137.3...

This manual is also suitable for:

Voyager e5788

TANDBERG Voyager E5784 Reference Manual

Table of Contents

Chapter 2 Installing the Equipment

Section 3

Section 4

Quick Links

Software Version 3.9.0

Chapters

Related Manuals for TANDBERG Voyager E5784

Summary of Contents for TANDBERG Voyager E5784