TANDBERG E5714 Instruction Manual
  1. Manuals
  2. Brands
  3. TANDBERG Manuals
  4. Media Converter
  5. E5714 DSNG Voyager
  6. Instruction manual

TANDBERG E5714 Instruction Manual

Dsng, deng voyager encoder build version 2.1.0 to 3.1.0 (and later) m2/voy/e5714, m2/voy/e5740-xxx, m2/voy/e5715, m2/voy/e5750 and options
Hide thumbs Also See for E5714:
Table of Contents

Advertisement

Quick Links

See also: Reference Manual
ST.TM.E10076.3
Issue 3
ENGLISH (UK)

INSTRUCTION MANUAL

E5714/E5740-xxx DSNG, E5715/E5750
DENG Voyager Encoder
Build Version 2.1.0 to 3.1.0 (and later)
M2/VOY/E5714, M2/VOY/E5740-xxx,
M2/VOY/E5715, M2/VOY/E5750
and Options

Advertisement

Table of Contents
loading

Related Manuals for TANDBERG E5714

Summary of Contents for TANDBERG E5714

  • Page 1: Instruction Manual

    ST.TM.E10076.3 Issue 3 ENGLISH (UK) INSTRUCTION MANUAL E5714/E5740-xxx DSNG, E5715/E5750 DENG Voyager Encoder Build Version 2.1.0 to 3.1.0 (and later) M2/VOY/E5714, M2/VOY/E5740-xxx, M2/VOY/E5715, M2/VOY/E5750 and Options...
  • Page 2 This document and the information contained in it is the property of TANDBERG Television Ltd and may be the subject of patents pending and granted. It must not be used for commercial purposes nor copied, disclosed, reproduced, stored in a retrieval system or...
  • Page 3 List of Contents Chapter 1: Introduction to the Basic Encoder Gives a general description of the equipment and its main features and functions. Identifies the controls, indicators and connectors on the front and rear panels. Chapter 2: Installing the Equipment Provides a guide to the suitability of an installation and gives detailed procedures for the preparation and installation of the equipment.

  • Page 4: About This Manual

    Encoder the original terms are used in the text of this manual. Page iv Build Version Comments 2.1.0 – 2.2.0 E5714/E5740 initial release. 2.1.0 – 3.0.0 Update for 3.0.0. 2.1.0 – 3.1.0 Update for 3.1.0. New option modules added. Simple Network Management Protocol...
  • Page 5 Xilinx Inc. Trademarks Pozidriv™ is a trademark of European Industrial Services. Reflex™ is a trademark of TANDBERG Television. Windows NT™ is a trademark of Microsoft Corporation. STREAMS™ is a trademark of TANDBERG Television. NDS™ is a trademark of NDS Limited.

  • Page 6: Emc Compliance

    Preliminary Pages Warnings, Cautions and Notes Heed Warnings All warnings on the product and in the operating instructions should be adhered to. The manufacturer can not be held responsible for injuries or damage where warnings and cautions have been ignored or taken lightly. Read Instructions All the safety and operating instructions should be read before this product is operated.

  • Page 7: Contact Information

    TANDBERG Television and your business. Warranty All TANDBERG Products and Systems are designed and built to the highest standards and are covered under a comprehensive 12 month warranty. Levels of Continuing TANDBERG Television Service Support For stand-alone equipment, then TANDBERG Television BASIC Advantage is the value for money choice for you.
  • Page 8 Preliminary Pages Technical Training Training Courses TANDBERG Television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. TANDBERG can provide both regularly scheduled courses and training tailored to individual needs. Courses can be run either at your premises or at one of our dedicated training facilities.

  • Page 9: Table Of Contents

    Build Revision ... 1-5 1.2 Role of the Encoder in a System... 1-5 1.2.1 Typical System ... 1-5 1.2.2 DSNG Systems... 1-6 Overview... 1-6 E5714 ... 1-7 E5740/E5760... 1-7 1.2.3 DENG Systems... 1-7 1.3 Summary of Features... 1-8 1.3.1 Video Encoding... 1-8 MPEG-2 Encoding ...
  • Page 10 Figure 1.7: 1U Encoder Front Panel Indicators ...1-16 Figure 1.8: Stand-by Switch ...1-17 Figure 1.9: 2U Encoder Front Panel Indicators ...1-17 Figure 1.10: E5714 (1U) Rear Panel Component Parts and Connectors...1-18 Figure 1.11: E5715 (1U) Rear Panel Component Parts and Connectors...1-18...

  • Page 11: Introduction To The Basic Encoder

    What Equipment is Covered by This Manual Equipment Models Each model of Encoder comprises an enclosure with a Base Board and Modulator fitted as standard. The E5714 and E5740 are fitted with a Satellite Modulator; the E5715 and E5750 are fitted with an OFDM Modulator.

  • Page 12: Figure 1.1: 1U Encoder Front View

    Introduction to the Basic Encoder There are vacant slots for option modules; one in the E5714 and E5715; three in the E5760; four in the E5740; five in the E5750. These slots can be occupied by any combinations of modules shown in Chapter 3, Options and Upgrades.

  • Page 13: Information Label

    Information Label There are two information labels which identify the configuration of the unit. Figure 1.3 and Figure 1.4 are typical examples. Serial Number A unique number for unit identification Figure 1.3: Information Label 1 Bar Code Used for unit identification in the manufacturing process Figure 1.4: Information Label 2 Hardware Configuration...

  • Page 14: Dsng Systems

    Introduction to the Basic Encoder The E5714 and E5740 contain the same high performance encoder. The E5714 is a 1U chassis housing the encoder and a QPSK satellite modulator. The E5740 is a 2U chassis housing the encoder, and a satellite modulator...

  • Page 15: E5714

    E5714 The satellite modulator within the E5714 supports QPSK modulation in accordance with EN 300 421 (DVB-S). It provides a main and monitoring IF Output. The IF frequency can be tuned between 50 MHz and 90 MHz. E5740/E5760 The satellite modulator fitted within the E5740 is capable of QPSK modulation in accordance with EN 300 421 (DVB-S), and is also capable of 8PSK and 16QAM modulation in accordance with EN 301 210 (DVB-DSNG).

  • Page 16: Summary Of Features

    Introduction to the Basic Encoder Summary of Features 1.3.1 Video Encoding MPEG-2 Encoding The Encoder processes a broadcast-standard video signal into a compressed encoded bit-stream in accordance with: · The MPEG-2 Main profile @ Main level (MP@ML) specification (ISO/IEC 13818) ·...

  • Page 17: Motion Estimation

    · Fully exhaustive motion estimation · An internal frame synchroniser (see Internal Frame Synchroniser on Page 1-10) · Support for Active Format Descriptor (AFD) (see Chapter 4, Operating the Equipment Locally, Table 4.36) · Support for a variety of Group of Pictures (GOP) structures with a variable number of B frames ·...

  • Page 18: Internal Frame Synchroniser

    Introduction to the Basic Encoder Table 1.4: Video Coding Resolutions 625 Line Modes 720 pixels x 576 lines 704 pixels x 576 lines 640 pixels x 576 lines 544 pixels x 576 lines 480 pixels x 576 lines 352 pixels x 576 lines 352 pixels x 288 lines Internal Frame Synchroniser An internal frame synchroniser is provided to accommodate slight...

  • Page 19: Audio Inputs

    Audio Inputs The standard audio input is: · AUDIO IN – 15-way male D-type - software selectable balanced analogue or digital AES/EBU, with AES/EBU on left only. A break-out cable is supplied which plugs into this connector and provides a more convenient means of connecting the audio inputs via five connectors.

  • Page 20: Test Tones

    Introduction to the Basic Encoder Test Tones The equipment can be configured to generate a test tone for alignment purposes. Refer to Annex B, Technical Specification for level and frequency. Audio Variable Bit-rate MPEG-1 audio output bit-rate (see Table 1.5) is selectable in the range 32 kbit/s -384 kbit/s (dependent on configuration).

  • Page 21: Vertical Blanking Interval (Vbi) Line Processing Modes

    Table 1.6: Dolby Digital Audio Encoding Bit-rates Bit-rate Single Channel (kbit/s) Mono (1/0) 1.3.3 Vertical Blanking Interval (VBI) Line Processing Modes Introduction The Encoder has three modes for processing VBI lines. NOTE… A maximum of eight VBI lines per field may be extracted. This limit does not apply to Teletext. VBI in Picture By selecting the VBI in Picture extended active picture format available in the MPEG 4:2:2 specification the Encoder compresses and transmits the...

  • Page 22: Vbi User Data

    Introduction to the Basic Encoder VBI User Data Closed Caption data, together with other formats such as VITC and AFD, can be transmitted in the user data field of the video or relevant part of the video stream. VBI in PID The Encoder has the ability to extract and transmit a wide variety of VBI line formats.

  • Page 23: Outputs

    1.3.6 IF Modulation E5714 The internal satellite modulator within the E5714 supports QPSK modulation in accordance with EN 300 421 (DVB-S). It provides a main and monitoring IF Output. The IF frequency can be tuned between 50 MHz and 90 MHz in steps of 125 kHz. The maximum symbol rate is 30 Msym/s 60 MHz to 80 MHz (20 Msym/s at 50 MHz and 90 MHz).

  • Page 24: Guided Tour

    Introduction to the Basic Encoder Guided Tour 1.4.1 Enclosure There are two sizes of enclosure, 1U and 2U versions. The enclosure is used as a stand-alone unit. All inputs and outputs are via rear panel connectors. 1.4.2 The User Interface The Encoder itself provides no controls at the rear panel but there is a display and keypad at the front panel.

  • Page 25: Power Supply Stand-By Switch

    Power Supply Stand-by Switch The use of this switch puts the Encoder into stand-by mode. It powers down the supply rails of the display and internal circuits within the unit. The switch type avoids accidental powering-down of the Encoder. For normal use ensure that the I is always at the top (see Figure 1.8).

  • Page 26: 1U Chassis

    Introduction to the Basic Encoder 1U Chassis IF Out Main Base Board Alarm RS-422 Data Figure 1.10: E5714 (1U) Rear Panel Component Parts and Connectors IF Out 1 Base Board Alarm RS-422 Data Figure 1.11: E5715 (1U) Rear Panel Component Parts and Connectors...

  • Page 27: Boards In The Basic Encoder

    (see Table 1.8). Option modules can be fitted in the remaining slots (see Equipment Models on page 1-3 and Chapter 3, Options and Upgrades). Table 1.8: Boards in the Basic Encoder Model Number E5714 E5715 E5740-IF E5740-LBAND E5750 Access to the modules or boards in the basic Encoder is not required for normal operation and may invalidate the warranty.
  • Page 28 Introduction to the Basic Encoder BLANK Page 1-20 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 29 Ethernet #1 and #2...2-16 Alarm...2-16 Remote Control...2-17 2.6.9 Data...2-17 RS-232 Connector ...2-17 RS-422 Connector ...2-18 2.6.10 Satellite Modulator IF Output (E5714 and E5740 IF) ...2-19 IF Out (Main)...2-19 IF Out (Monitor)...2-19 2.6.11 Satellite Modulator L-Band Output (E5740 LBAND) ...2-19 L-Band In...2-19 L-Band Out (Main)...2-20...

  • Page 30: Figure 1.10: E5714 (1U) Rear Panel Component Parts And Connectors

    List of Figures Figure 2.1: Fitting the Encoder into a Rack ...2-5 Figure 2.2: Air Path Through the Enclosure ...2-6 Figure 2.3: E5714 (1U) Rear Panel Component Parts and Connectors...2-10 Figure 2.4: E5715 (1U) Rear Panel Component Parts and Connectors...2-11 Figure 2.5: E5740-IF (2U) Rear Panel Component Parts and...

  • Page 31: Introduction

    IF THE ENCODER HAS BEEN SUBJECT TO A LIGHTNING STRIKE OR POWER SURGE WHICH HAS STOPPED IT WORKING, DISCONNECT THE POWER IMMEDIATELY. DO NOT REAPPLY POWER UNTIL IT HAS BEEN CHECKED FOR SAFETY. IF IN DOUBT, CONTACT TANDBERG Where appropriate, ensure this product has an adequate level of lightning protection.

  • Page 32: Fcc

    Do not place this product on an unstable cart, stand, bracket, or table. The product may fall, causing serious injury and serious damage to the product. Use only with a cart, stand, bracket or table recommended by TANDBERG Television. Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder...

  • Page 33: Cable Routing

    Location of screws to attach Encoder to rack. Same at the opposite side of the Encoder. Figure 2.1: Fitting the Encoder into a Rack 2.3.2 Cable Routing Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them.
  • Page 34 Installing the Equipment The unit is designed for stationary or fixed use only. Ensure it is firmly and safely located and has an adequate through-flow of air. Allow at least 50 mm free air-space at each side of the equipment. Units in racks can be stacked without ventilation panels between.

  • Page 35: Ac Mains Operating Voltage And Earthing

    AC Mains Operating Voltage and Earthing 2.4.1 AC Power Supply This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your business, consult a qualified electrical engineer or See Annex B, Technical Specification for a full power supply specification.

  • Page 36: Connecting The Encoder To The Ac Power Supply

    Installing the Equipment The unit has a Technical earth terminal (marked with rear panel. Its use is recommended. This is NOT a Protective earth for electric shock protection. The terminal is provided to: 1. Ensure all equipment chassis fixed within a rack are at the same Technical earth potential.

  • Page 37: Dc Power Cable And Earthing

    The internal dc power supply module used in this equipment is designed for use on dc supplies ranging from 12 to 36 volts dc. (see Annex B, Technical Specification for a full power supply specification). The dc connections within the Encoder are floating (both are isolated from the Encoder case and earth connection).

  • Page 38: Dc Power Connector (Encoder)

    EMC requirements (see Annex B, Technical Specification). IF Out Main Base Board Alarm RS-422 Data Figure 2.3: E5714 (1U) Rear Panel Component Parts and Connectors Page 2-10 … WARNING ATTENTION TO THE CABLE AT CONNECTION POINTS. Voltage Condition Earth/Vehicle frame...
  • Page 39 Reference Out Audio In and Audio Composite Reference Out SDI In H Sync Video Option Slot 6 Technical Earth TANDBERG Television use only Audio In and Audio Composite Reference Out SDI In H Sync Video Option Slot 6 Technical Earth...

  • Page 40: Connecting Up The Basic Encoder

    Installing the Equipment RS-422 Data Alarm Base Board Option Slots 4-5 Option Slot 4 Option Slot 1-3 Option Slot 1 Figure 2.7: E5750 (2U) Rear Panel Component Parts and Connectors 2.6.2 Connecting Up the Basic Encoder Once the unit has been installed in its intended operating position, it is ready to be connected up to the rest of the system equipment (see Figure 2.8), providing it too has been installed (see Section 2.5, DC Operating Voltage and Earthing for pin-out details of the connectors).

  • Page 41: Power Supply

    Do not move or install equipment whilst it is still attached to the mains supply. Ensure ESD precautions are observed whilst interconnecting equipment. NOTE… See Chapter 3 for information relating to Options and Upgrades. 2.6.3 Power Supply Section 2.4, AC Mains Operating Voltage and Earthing provides details of power supply connection, Protective earthing and safety.

  • Page 42: Comp Video

    Installing the Equipment Table 2.4: H SYNC Connector Signal Centre Video Input Screen Ground Impedance 75 W COMP VIDEO A 75 W BNC connector provides a high quality analogue video input to the unit. See Chapter 4, Operating the Equipment Locally, Video Input Option for the types of video and selection method.

  • Page 43: Asi Out 1, 2 And 3 Outputs

    2.6.8 Control Interfaces Connection Operation of the Encoder from a TANDBERG Television control system is via the Ethernet network running the Simple Network Management Protocol (SNMP) protocol. Connect the ETHERNET connector to the controller (for example, MEM). Local control is implemented through the front panel keypad and display.

  • Page 44: Ethernet #1 And #2

    Installing the Equipment Ethernet #1 and #2 An 8-way, RJ-45 connector provides a 10BaseT Ethernet interface for communications with the MEM for control and monitoring. The Encoder has a single switched Ethernet channel. Ethernet#1 is selected as default at power-up. If a carrier is not detected on Ethernet#1 then the input switches to Ethernet#2.

  • Page 45: Remote Control

    Remote Control A 9-way, D-type male connector provides an RS-232/RS-485 port for remote control of the Encoder (see Serial Protocol Option). This connector is wired as a DTE. Table 2.10: Remote Control Connector (RS-232/ RS-485) Remote (DTE) Signal Name Transmit Data Received Data Signal Ground Transmit Data B...

  • Page 46: Rs-422 Connector

    Installing the Equipment NOTES… Signal names are with respect to a DTE in accordance with the RS-232 specification. Remote pin numbers only apply to a 9-way D-type connector. 25-way connectors have Received Data on pin 3 and Transmit Data on pin 2 (see RS –232 specification).

  • Page 47: Satellite Modulator If Output (E5714 And E5740 If)

    2.6.10 Satellite Modulator IF Output (E5714 and E5740 IF) IF Out (Main) 75 W BNC socket provides an IF output. Table 2.13: IF Out Connector (Main) Item Connector type Type Connector designation Pin-outs Centre Screen IF Out (Monitor) 75 W BNC socket provides an IF output used for monitoring.

  • Page 48: L-Band Out (Main)

    Installing the Equipment L-Band Out (Main) 50 W SMA female connector provides the main L-band output. This can also provide +24 V dc at up to 500 mA to power an up-converter. Table 2.16: L-band Out (Main) Connector Item Connector Type Type Connector designation Pin-outs...
  • Page 49 IF Out 2 A 75 W BNC socket provides a 70 MHz IF output used for monitoring. Table 2.18: IF Out 2 Connector Item Connector Type Type Connector designation Pin-outs Powering Up/Down 2.7.1 Before Powering Up Before powering up the Encoder, check that: 1.
  • Page 50 Installing the Equipment Setting the Encoder IP Address 2.8.1 Methods of Changing the Encoder IP Address If, for any reason, the IP address has to be changed, this can be achieved via the front panel menus (see Section 4.7.4 Remote Control Menu) or by Telnet (see Section 2.8.3, Via Telnet).
  • Page 51 Contents 3.1 What’s Available... 3-3 3.1.1 Option Functions... 3-3 3.1.2 Limitations on Number of Option Modules (2U Only) ... 3-4 Overview... 3-4 E5740 Option Slots... 3-4 E5750 Option Slots... 3-4 3.1.3 Limitations on Use of Option Modules ... 3-4 3.1.4 How to See Which Options are Fitted/Enabled...
  • Page 52 Options and Upgrades 3.10 16QAM Demodulator (M2/EOM2/SATDEMOD) ...3-24 3.10.1 Overview ...3-24 3.10.2 Assembly...3-25 Rear Panel ...3-25 L-Band Inputs...3-25 3.11 IP Output Card (M2/EOM2/IP)...3-25 3.11.1 Overview ...3-25 3.11.2 Assembly...3-26 Rear Panel ...3-26 ASI In ...3-26 RS-232 Control ...3-26 ASI Out...3-27 Ethernet Output...3-27 3.12 Software Options ...3-27 3.12.1 M2/ESO2/NR ...3-27 3.12.2 M2/ESO2/PU...3-27...

  • Page 53: What's Available

    What’s Available 3.1.1 Option Functions The basic Encoder functionality can be enhanced with the inclusion of options, hardware and software. Each hardware option module consists of a horizontally mounted PCB with rear panel connector space (except the M2/EDCOM2/BISS which has no external connectors and does not occupy an option slot).

  • Page 54: Limitations On Number Of Option Modules (2U Only)

    Options and Upgrades Table 3.2: Software Options Marketing Code M2/ESO2/NR M2/ESO2/PU M2/ESO2/VBR M2/ESO2/422 M2/ESO2/RAS M2/ESO2/ACON M2/ESO2/AC3 M2/ESO2/SM38PSK M2/ESO2/SM316QAM M2/ESO2/8PSKDEMOD 8PSK Demodulation (only applicable if M2/EOM2/SAT M2/ESO2/16QAM DEMOD M2/ESO2/LSYM 3.1.2 Limitations on Number of Option Modules (2U Only) Overview If the Remux option is not fitted then there can be a maximum of three option modules (any combination of additional audio and data).

  • Page 55: Bit-Rate Limits With Reflex Licence And/Or Performance Upgrade

    Bit-rate Limits With Reflex Licence and/or Performance Upgrade A user with a REFLEX licence (M2/ESO2/VBR) but no Performance Upgrade (M2/ESO2/PU) will be able to get lower bit-rates than 1.5 Mbit/s. This only occurs in Seamless modes. However, because the Performance Upgrade has not been bought the picture quality will be reduced (see Table 3.3).

  • Page 56: Additional Audio And Linear Pcm Option (M2/Eom2/Audlin)

    Options and Upgrades BISS scrambling (when fitted) is enabled and controlled via the Setup/Mux Menu (see Chapter 4, Operating the Equipment Locally, Section 4.12.12). Additional Audio and Linear PCM Option (M2/EOM2/AUDLIN) 3.4.1 Overview The Additional Audio option module supplements the audio encoding functionality of the Encoder.

  • Page 57: Assembly

    3.4.2 Assembly Rear Panel Analogue Composite Video COMP VIDEO Serial Digital Interface SDI IN Audio Input AUDIO IN Mono 1 / Stereo 1 Right Mono 2 / Stereo 1 Left Mono 3 / Stereo 2 Right Mono 4 / Stereo 2 Left NOTE…...
  • Page 58 Options and Upgrades Table 3.4: Audio In Connector Analogue Left Channel A (+) Not connected Right Channel A (-) Left Channel B (+) Not connected Right Channel B (-) Not connected NOTES… In analogue mode termination is either 20 kW or 600 W. In AES/EBU mode termination is 110 W (default).

  • Page 59: And Rs-422 Data Input Option (M2/Eom2/Dat)

    RS-232 and RS-422 Data Input Option (M2/EOM2/DAT) 3.5.1 Overview NOTE… The Data Input Option does not report errors back to the host, thus no alarms are raised by the Encoder. The RS-232 and RS-422 Data Input option module comes with an RS-422 synchronous data input and an RS-232 asynchronous data input.

  • Page 60: Async Connector

    Options and Upgrades Async Connector A 9-way, D-type female connector provides an RS-232 asynchronous, serial communications data input interface. Table 3.5: RS-232 Data Connector (Option Module) - Asynchronous Remote (DTE) Male Signal Name Data Carrier Detected Received Data Transmit Data Signal Ground Data Set Ready (DSR) Clear to Send (CTS)
  • Page 61 Table 3.6: RS-422 Data Connector (Option Module) - Synchronous Remote (DTE) Signal Name Transmit Data A Data Terminal Ready A Received Data A Data Set Ready A Received Clock A Transmit Clock A Signal Ground Transmit Data B Data Terminal Ready B Received Data B Data Set Ready B Received Clock B...

  • Page 62: Remux Option (M2/Eom2/Remux)

    Options and Upgrades Remux Option (M2/EOM2/REMUX) 3.6.1 Overview NOTE… The M2/EOM2/REMUX Remux Option Module is supported by Build version 2.2.0 and later. The Remux option module is capable of accepting up to three separate transport streams via ASI connectors, and one transport stream from the host Encoder.

  • Page 63: Dvb Asi In 1, 2 And 3 Connectors

    DVB ASI IN 1, 2 and 3 Connectors A 75 W BNC connector provides an input to the unit. Table 3.7: DVB ASI In Connector Signal Centre Signal Screen Ground NOTE… When connecting the inputs, always start from DVB ASI IN 1 and work upwards. DVB ASI OUT 1 Connector A 75 W BNC connector provides an output from the unit.
  • Page 64 Options and Upgrades Contributing Encoders VIDEO (ANALOGUE) VIDEO (DIGITAL) Service 2 AUDIO SYNC DATA ASYNC DATA VIDEO (ANALOGUE) VIDEO (DIGITAL) Service 3 AUDIO SYNC DATA ASYNC DATA VIDEO (ANALOGUE) VIDEO (DIGITAL) Service 4 AUDIO SYNC DATA ASYNC DATA Figure 3.4: Block Diagram – One Stage of Remultiplexing Similarly, if two stages of remultiplexing are introduced, thirteen Encoders can be combined, providing up to thirteen services in the remultiplexed output.

  • Page 65: Function Of Remultiplexer

    3.6.4 Function of Remultiplexer It is the function of the Remultiplexer to combine the locally generated host services with the externally supplied input services, connected via ASI inputs to the rear of the unit. If the Service ID (DVB) or Program Number (ATSC), PIDs or service names, of two or more of the services clash, the Remultiplexer can remap the Service ID or program number, remap PIDs, and alter the service names to resolve the clash.

  • Page 66: Using The Remultiplexer

    NOTE… It is possible to remultiplex any DVB or ATSC compliant transport stream but at the time of publication, only transport streams generated by TANDBERG Television equipment are guaranteed to work when fed to the Remultiplexing module. The equipment will automatically detect the services on these inputs. The list of detected services is displayed in the Setup/Mux Menu.

  • Page 67: What To Do If Overflow Occurs

    The easiest way to configure the bit-rates to avoid overflow, is as follows: 1. Divide the 188 byte output bit-rate of the primary (master) remultiplexing unit, (this can be found in the Setup/Mux/Remux Module/Output Bit-rate), by the number of contributing services (including the primary service).

  • Page 68: Xlr Expander Card Option (M2/Eom2/Xlr)

    Options and Upgrades XLR Expander Card Option (M2/EOM2/XLR) 3.7.1 Overview NOTE… The M2/EOM2/XLR XLR Expander Card Option is supported by Build version 3.0 and later. The XLR Expander Card Option permits Encoders to input and output a stereo audio pair via XLR connectors. The option occupies two vertical option slots, 1 and 4, due to the size of the XLRs.

  • Page 69: Audio In Connector

    NOTES… Pre-encoded signals cannot be reconstructed on the analogue outputs. Pre-encoded signals will raise an alarm on the digital output. Analogue /AES_EBU Left (Balanced) Analogue Right (Balanced) Analogue /AES_EBU Left (Balanced) Analogue Right (Balanced) Figure 3.7: XLR Expander Card Option (M2/EOM2/XLR) The XLR Expander Card option comprises Assembly S12556 and Card S12557.

  • Page 70: Audio Out Connector

    Options and Upgrades NOTES… When the Encoder is powered down the digital channel is selected with 110 W termination. The digital audio input does not support SPDIF. Audio Out Connector Two XLR male connectors provide a stereo pair. Each connector carries a single channel of an analogue stereo pair.

  • Page 71: Sd Decoder Option (M2/Eom2/Dec)

    SD Decoder Option (M2/EOM2/DEC) 3.8.1 Overview NOTES… The M2/EOM2/DEC SD Decoder Option is supported by Build version 3.1 and later. This option module only fits into option slot 6 in the E5740, and must always be accompanied by a demodulator option module in slot 5. This option module is a complete MPEG-2 standard definition decoder, capable of decoding 422P@ML and MP@ML.

  • Page 72: Composite Video Output

    Options and Upgrades Composite Video Output A 75 W female BNC connector provides a composite video output. See Annex B, Technical Specification for a list of supported video standards. Table 3.15: Composite Video Connector Item Connector Type Connector designation Pin-outs Centre Screen Audio Output...

  • Page 73: Rs-232/Rs-422 Data Output

    RS-232/RS-422 Data Output A 9-way D-type socket provides the data outputs. Table 3.17: RS232/RS422 Data Output Connector Item Connector Type Connector designation Pin-outs QPSK Demodulator (M2/EOM2/QPSKDEMOD) 3.9.1 Overview NOTE… The M2/EOM2/QPSKDEMOD QPSK Demodulator Option is supported by Build version 3.1 and later. The module allows the Encoder to receive and demodulate satellite transmissions that comply to EN 300 421 (DVB-S).

  • Page 74: Assembly

    Options and Upgrades 3.9.2 Assembly Rear Panel IF In A 75 W female BNC connector provides an IF Input. Table 3.18: IF In Connector Item Connector Type Connector designation Pin-outs Centre Screen RF In Two 75 W F-type female connectors provide RF inputs.

  • Page 75: 3.10.2 Assembly

    3.10.2 Assembly Rear Panel L-Band Inputs Two 75 W F-type female connectors provide L-band inputs. Table 3.20: L-Band Input Connector Item Connector Type Connector designation Pin-outs Centre Screen 3.11 IP Output Card (M2/EOM2/IP) 3.11.1 Overview The IP Output card provides a 10/100 BaseT Ethernet port, out of which the transport stream generated by the Encoder can be output in UDP packets at up to 50 Mbit/s.

  • Page 76: 3.11.2 Assembly

    Connector designation Pin-outs Centre Screen RS-232 Control A 3.5mm socket provides a debug interface. NOTE… This connector is for TANDBERG Television use only. Page 3-26 Specification 75 W BNC Female ASI IN Signal Ground Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder...

  • Page 77: Asi Out

    ASI Out A 75 W female BNC connector provides an ASI output. NOTE… This connector is not used. Table 3.22: ASI Out Connector Item Connector Type Connector designation Pin-outs Centre Screen Ethernet Output An RJ-45 connector provides a 10/100 BaseT Ethernet port.

  • Page 78: 3.12.3 M2/Eso2/Vbr

    Options and Upgrades 3.12.3 M2/ESO2/VBR This purchasable option upgrades the Encoder to include variable bit-rate. Contact Customer Services for details. 3.12.4 M2/ESO2/422 This purchasable option upgrades the Encoder to include 4:2:2 video encoding mode. Contact Customer Services for details. 3.12.5 M2/ESO2/RAS This purchasable option upgrades the Encoder to include RAS mode.
  • Page 79 Operating the Equipment Locally Contents 4.1 Introduction ... 4-9 4.2 Establishing Local Control (1U)... 4-9 4.3 Navigating the Display Screens (1U) ... 4-9 4.3.1 Introduction... 4-9 4.3.2 Navigating the Menus (1U) ... 4-10 4.3.3 Changing a Setting (1U) ... 4-10 Overview...
  • Page 80 Operating the Equipment Locally SNMP Master Option ...4-25 Last SNMP Master Option ...4-25 Last SNMP Poll Option ...4-25 SNMP Trap IP Option ...4-25 SABus Address Option ...4-25 Serial Protocol Option ...4-25 SABus Baud Rate Option...4-25 SABus Data Bits Option ...4-26 4.7.5 General Menu ...4-26 Overview ...4-26 Model Number Option...4-26...
  • Page 81 Audio Delay Option... 4-57 External Delay Option... 4-57 Clip Level Option ... 4-58 Impedance Option ... 4-58 Language or Language Left/Right Option... 4-58 SMPTE 302M Standard Option ... 4-59 Channel Option... 4-59 Bit Stream Mode Option ... 4-59 Dialogue Level Option ... 4-60 Dolby Srnd Mode Option ...
  • Page 82 Operating the Equipment Locally Tx Bandwidth Option...4-81 Bit-rate (188) Option...4-81 Bit-rate (204) Option...4-81 Preset Pwr Low Option ...4-81 Preset Pwr Norm Option ...4-81 Sat Deliv Freq Option...4-82 Sat Orb Pos Option ...4-82 Sat West/East Option...4-82 Polarisation Option...4-83 Status Only Options for the Satellite Modulator Menu ...4-83 4.11.9 Output Format = Satellite Modulator (L- Band Output) (3.1 and later) ...4-83...
  • Page 83 Major Channel Option... 4-101 Minor Channel Option... 4-101 Logical Channel Option ... 4-101 CA Input Option ... 4-101 BISS Key Code Option ... 4-101 Enc Session Word Option... 4-101 Session Word Option... 4-101 PMT PID Option... 4-102 PCR PID Option... 4-102 Video Option...
  • Page 84 Figure 4.9: Menu Hierarchy – Setup/System Menu...4-18 Figure 4.10: Menu Hierarchy – Setup/Video Menu ...4-32 Figure 4.11: Setting up the Video Input...4-33 Figure 4.12: VBI Structure Implemented by TANDBERG for 525-line Systems...4-50 Figure 4.13: VBI Structure Implemented by TANDBERG for 625-line Systems...4-51...
  • Page 85 Table 4.80: Carriers Options ... 4-75 Table 4.81: Other Frequency Options ... 4-76 Table 4.82: Modulation Type Options... 4-76 Table 4.83: FEC (Outer) Options... 4-76 Table 4.84: FEC (Inner) Options ... 4-77 Table 4.85: Symbol Rate Options... 4-77 Table 4.86: Modulation Type Options... 4-77 Table 4.87: Orbital Position Options...
  • Page 86 Operating the Equipment Locally BLANK Page 4-8 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...

  • Page 87: Operating The Equipment Locally

    Introduction The front panel display and keypad are used to configure, control and monitor the Encoder. The control interface is a structured menu which gives access to the various options. This chapter describes the menu hierarchy and menu items in detail. NOTES…...

  • Page 88: Navigating The Menus (1U)

    Operating the Equipment Locally ENTER button CANCEL button Figure 4.2: 1U Navigation Keys and Buttons NOTE… The navigation keys are referred to as LEFT, RIGHT, UP and DOWN, indicating the direction of the arrows. From the Summary Screen select the Main Menu by pressing ENTER, RIGHT, UP or DOWN.

  • Page 89: For Multiple Choice Entry

    For Multiple Choice Entry · DOWN · · RIGHT · LEFT · ENTER · CANCEL For Text or Numeric Entry The character list for text entry contains the following characters: space ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz 0123456789/+-=.,:;_!$%^&*(){}[]@’#<>?| For numeric entry only 0-9 are displayed. ·...

  • Page 90: Establishing Local Control (2U)

    Operating the Equipment Locally Establishing Local Control (2U) 4.4.1 Input Monitor At power-on the Encoder runs through a boot sequence (boot time with Remux option module is approximately 90 seconds). An initial Input Monitor screen is shown. This displays a picture of the currently selected video source, the service name of the video channel being encoded, the audio A and B channels in the form of bargraphs, and the multiplexer and video bit-rates.

  • Page 91: A(Udio)/V(Ideo) Menu (2U)

    4.4.3 A(udio)/V(ideo) Menu (2U) The A/V Menu contains some basic video and audio options. They can all be changed with the exception of the audio input levels. These are only indicators of the current audio input level and are status only. Only those video input selections compatible with the currently selected frame rate can be chosen from this menu.

  • Page 92: How To Use The Keypad

    Operating the Equipment Locally Each softkey on each side of the display is used to access, select and sometimes amend the menu item associated with Figure 4.6: 2U Keypad and Display Functions 4.5.2 How to Use the Keypad Each key on the keypad has more than one inscription. One press of a key makes the number appear on the display screen, two quick presses makes the first letter appear etc.

  • Page 93: How To Use The Functions Associated With Softkeys

    4.5.3 How to Use the Functions Associated with Softkeys The following display screens show the different functions associated with the options. Press Left and Right to move the underscore to the next letter that you want to change. Press Ins to insert a space where the underscore is.
  • Page 94 Operating the Equipment Locally Input Monitor Screen Ops... A/V... More... Summary Screen Cfgs... More... Quit Advanced Menu Setup... Errors... Diagnostics... Ops... Configs... Quit Config Menu From the Summary Screen, see the Config Menu Figure 4.8: Menu Hierarchy – Summary Screen and Advanced Menus Page 4-16 Audio/Video Menu...

  • Page 95: Summary Screen And Advanced Menus

    4.5.6 Summary Screen and Advanced Menus See Figure 4.8, for the top-level menu hierarchy. Press the More softkey in the Summary Screen to access the Advanced Menu. The Advanced Menu provides options for configuring and testing the Encoder. Setup Menu The Setup Menu can be selected from the Advanced Menu by pressing the Setup softkey (see Figure 4.8 for menu structure).
  • Page 96 Software Release SABus Baud Rate Fan Control SABus Data Bits These menus are mainly for TANDBERG Television use for testing purposes. The Mdb Services and Default Mbd Services Service menus are only available if, in the Advanced Menu, the number Menu of Services is set to more than one.

  • Page 97: Service Info Menu (Syntax = Atsc)

    4.7.2 Service Info Menu (Syntax = ATSC Overview The Service Info Menu is selected from the System Menu by pressing the Service Info softkey. This menu provides options for configuring the Service Information (SI) parameters transmitted in the output transport stream.

  • Page 98: Major Channel Option (3.0 And Later)

    Operating the Equipment Locally Table 4.3: SI Level Options Selected Option PAT/PMT/CAT only PAT/PMT only On (No EIT) Major Channel Option (3.0 and later) This is associated with the field major_channel_number and is used to group all channels that are to be identified as belonging to a particular broadcast corporation.

  • Page 99: Dst Start Date Option (3.0 And Later)

    DST Start Date Option (3.0 and later) To access the DST Start Date (Daylight Saving Time) option, press the DST Start Date softkey in the Service Info Menu. This option allows the Daylight Saving Time Start Date to be changed. DST End Date Option (3.0 and later) To access the DST End Date (Daylight Saving Time) option, press the DST End Date softkey in the Service Info Menu.

  • Page 100: Network Id Option

    Operating the Equipment Locally Table 4.5: SI Level Options Selected Option PAT/PMT/CAT only PAT/PMT only On (No EIT) Network Id Option To access the Network Id option, press the Network Id softkey in the Service Info Menu. This enables the Network Identity to be specified. Use the + and –...

  • Page 101: Transport Stream Id Option

    Transport Stream Id Option To access the Transport Stream Id option, press the Transport Stream Id softkey in the Service Info Menu. This enables the Transport Stream Identity to be specified. Use the + and – softkeys to scroll through the options and then press the Enter softkey after selecting one of them.

  • Page 102: Logical Chan Desc Option

    Operating the Equipment Locally Table 4.10: Audio AC-3 Descriptor Options Selected Option DVB & ATSC DVB only ATSC only Logical Chan Desc Option To access the Logical Chan Desc option, press the Logical Chan Desc softkey in the Service Info Menu. This enables the Logical Channel Descriptor to be turned On or Off.

  • Page 103: Snmp Master Option

    SNMP Master Option To access the SNMP Master option, press the SNMP Master softkey in the Remote Control Menu. This gives the SNMP Master’s IP address. If this is set, only one SNMP controller will be allowed access to the Encoder. It can be set to 000.000.000.000 to allow any controller access.

  • Page 104: Sabus Data Bits Option

    Operating the Equipment Locally Table 4.13: SABus Baud Rate Options Selected Option 1200 2400 4800 SABus Data Bits Option To access the SABus Data Bits option, press the SABus Data Bits softkey in the Remote Control Menu. Table 4.14: SABus Data Bits Options Selected Option 8 (1 stop bit) 7 (2 stop bits)

  • Page 105: Utc Offset Option

    To access the Screen Saver option, press the Screen Saver softkey in the General Menu. Table 4.16: Screen Saver Options Selected Option Top Level Menu TANDBERG Service Name Keypress Beep Option To access the Keypress Beep option, press the Keypress Beep softkey in the General Menu.

  • Page 106: Power Dip Recovery Option

    Upgrade Encoder softkey in the General Menu. This shows the serial number of the box, which is in the range of 0 to 65535. Send this number to TANDBERG Customer Services and they will return a software licence key to enter via the front panel to enable the features.

  • Page 107: Advanced Menu

    4.7.6 Advanced Menu Overview The Advanced Menu is selected from the System Menu by pressing the Advanced softkey. This menu provides options for the advanced parameters of the Encoder. See Figure 4.9 for the Advanced Menu structure. Setup Password Option There is no password originally required to edit parameters so if one is needed then it must be set.

  • Page 108: Action On Pid Error Option

    Operating the Equipment Locally Action On PID Error Option To access the Action on PID Error option, press the Action on PID Error softkey in the Advanced Menu. Table 4.21: Action on PID Error Options Selected Option Raise Alarm Auto Correct SNMP Control Option To access the SNMP Control option, press the SNMP Control softkey in the Advanced Menu.

  • Page 109: Build Menu

    One example of its use is when code has been downloaded in background mode (such as Base Board code or Video Compression Module (VCM) code) and you want to reset the Encoder, to action the new 4.7.7 Build Menu The Build Menu is selected from the System Menu by pressing the Build softkey.
  • Page 110 Operating the Equipment Locally Setup Menu Video Menu Video Source... Video Encoder... VBI... Menu Menu options depend on Frame Rate selected (in Video Source menu when Video Input is Digital). 29.97 Hz VBI on PID VBI PID VBI Component Tag VBI in Picture Closed Caption CC Format...

  • Page 111: Input Source Select

    Input Source Select NOTE… This option is available in Build version 3.1.0 and later. To access the Input Source Select option, press the Input Source Select softkey from the Video Source Menu. This allows the enabling or disabling of automatic frame rate detection. Table 4.24: Input Source Select Options Selected Option Manual...

  • Page 112: Video Locked Option

    Operating the Equipment Locally Table 4.25: Frame Rate Options Selected Option 29.97 Hz 25 Hz Video Locked Option This option indicates whether the video is locked. It is for status only and cannot be changed. Ident Text Option To access the Ident Text option, press the Ident Text softkey from the Video Source Menu.

  • Page 113: Op Video Loss Option

    To access the Video Bandwidth option, press the Video Bandwidth softkey from the Video Source Menu. Table 4.28: Video Bandwidth Options Selected Option Sharp Medium Soft Auto OP Video Loss Option This option gives the choice of what is displayed on the television screen in the event of losing video input.

  • Page 114: Default 625 Config And Default 525 Config

    Operating the Equipment Locally Table 4.30: Noise Reduction Options Selected Option Level 1 Level 2 Level 3 Default 625 Config and Default 525 Config NOTE… These options are available in Build version 3.1.0 and later. To access the Default 525/625 Config options, press the appropriate Default 525/625 Config softkey from the Video Source Menu.

  • Page 115: Compression Mode Option

    Table 4.31: Profile/Level Options Selected Option MP@ML 422P@ML Compression Mode Option To access the Compression Mode option, press the Compression Mode softkey in the Video Encoder Menu. This enables various compression modes to be selected in which some encoding parameters are automatically controlled depending on the selected encoding delay.

  • Page 116: Bit-Rate Option

    Operating the Equipment Locally Table 4.33: Seamless Mode Bit-rate (Full Resolution Only) Profile 4:2:0 4:2:2 Rate Buffer delay Seamless 1 mode can use video bit-rates from 0.8 Mbit/s to 10 Mbit/s, with the actual limits depending on video standard and resolution. This would be used for 4:2:0 DTH statistical multiplexing applications.
  • Page 117 It is possible to operate the Encoder in a stand-alone Variable Bit-rate (VBR) mode. When in this mode the bit-rate generated by the video encoder ranges between a minimum (Bmin - dependent on Compression Mode) and a maximum (Bmax - set by user, up to a limit defined by the Compression Mode).

  • Page 118: Delay Option

    Operating the Equipment Locally The required picture quality is set in the same menu by the VBR Target Quality item. When running in VBR Mode the two top-level status screens show the current bit-rate being used. This will typically vary. Delay Option This option indicates the current video delay.

  • Page 119: Aspect Ratio Option

    Table 4.34: Resolution Options Selected Option In Auto, pixel 625 Line Modes value in Auto (720x576) brackets varies with 720 x576 bit-rate that 704 x576 is set. 640 x576 544 x576 480 x576 352x576 352x288 (SIF) Aspect Ratio Option To access the Aspect Ratio option, press the Aspect Ratio softkey in the Video Encoder Menu.

  • Page 120: Gop Structure Option

    Operating the Equipment Locally Table 4.37: AFD Information Video Encoder Encoder AFD off Input Video Index Extraction Sequence_header aspect_ratio_infor mation Present Aspect ratio from Video Index Present Encoder setting No input Encoder setting Present but no Video Index data No input Encoder setting Present but no Video Index data...

  • Page 121: Gop Length Option

    GOP Length Option To access the Group of Pictures (GOP) Length option, press the GOP Length softkey in the Video Encoder Menu. This enables the video GOP structure length to be set. The structure length determines how regularly an I frame is transmitted. The I frame provides a regular reference from which predicted frames can be generated, thereby ensuring that predictions do not become wildly inaccurate.

  • Page 122: 3:2 Pulldown Option

    Operating the Equipment Locally With frame pictures a frame of a field 1 and field 2 is encoded as a single unit. With field pictures each individual field of video is encoded as a single unit, but must be followed or preceded by another field picture relating to its matching field.

  • Page 123: Pid Option

    PID Option The PID option is selected from the Video Encoder Menu by pressing the PID softkey. The option is used for entering or updating video PIDs, as required. Enter a PID then press the Enter softkey to accept it. To be DVB compliant, PIDs below 32 are reserved.

  • Page 124: Vertical Blanking Interval (Vbi) Menu

    Operating the Equipment Locally 4.8.4 Vertical Blanking Interval (VBI) Menu Overview The VBI Menu is selected from the Video Menu by pressing the VBI softkey. This menu permits the selection of VBI parameters. The VBI lines vary, according to whether the video source is 525 lines, 29.97 Hz or 625 lines, 25 Hz.

  • Page 125: Vbi In Picture Option

    VBI In Picture Option NOTES… The VBI in Picture option is only accessible if the selected video profile/level is 422P@ML VBI in Picture transmits the VBI waveform as part of the picture and as such will be subject to some distortion. Most analogue VBI types are robust against this type of distortion but others, e.g.

  • Page 126: Wss (Line 23) Option

    This option is only displayed if the video frame rate is set to 29.97 Hz. Table 4.42: CC Format Options Selected Option TANDBERG / NDS ATSC Auto Detect VITC Option To access the Auto Detect VITC option, press the Auto Detect VITC softkey in the VBI Menu.
  • Page 127 Table 4.43: VBI - Line ‘n’ Options Option Frame Rate = 29.97 Hz Vertical Interval Time Code Video Index Closed Caption Neilsen AMOL 1 Neilsen AMOL 11 Frame Rate = 25 Hz Vertical Interval Time Code Video Index Teletext System B (World System Teletext) Inverted Teletext Wide Screen Signalling...
  • Page 128 For compatibility with some older Receivers the start of coded video may need to begin at line 22. Contact Customer Services for details. Figure 4.12: VBI Structure Implemented by TANDBERG for 525-line Systems Page 4-50 Same options as line 10...
  • Page 129 ETS 300 294 is the specification which describes WSS. EN 300 472 is the specification associated with System B Teletext (World System Teletext). Figure 4.13: VBI Structure Implemented by TANDBERG for 625-line Systems Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...

  • Page 130: Audio Menu

    Operating the Equipment Locally Audio Menu 4.9.1 Overview The Audio Menu is selected from the Setup Menu by pressing the Audio softkey. This menu permits the selection of audio parameters. Any option with a clear circle next to it cannot be accessed and changed. It is for status information only (see Figure 4.15 for menu structure).
  • Page 131 Setup Menu Audio Menu Audio A... Audio B... Audio XLR... Audio Languages Dolby E Pass-Thru AC-3 Pass-Thru Source Source Coding Standard Coding Standard Auto Lip Sync Audio Bit-rate Coding Mode Lip Sync Offset Audio Delay Auto Lip Sync External Delay Audio Delay Lip Sync Offset Language...

  • Page 132: Source Option

    Operating the Equipment Locally Source Option To access the Source option, press the Source softkey in the Audio A Menu. Table 4.44: Source Options Selected Option Mute Test Tone Analogue Digital SDI Embedded 1 SDI Embedded 2 SDI Embedded 3 SDI Embedded 4 Coding Standard Option To access the Coding Standard option, press the Coding Standard...

  • Page 133: Audio Bit-Rate Option

    Audio Bit-rate Option NOTES… This option is only shown when the Coding Standard is AC-3 Pass-Thru, MPEG Layer 2 or Dolby Digital (AC-3). When AC-3 Pass-Thru is selected, Audio Bit-rate is status only. To access the Audio Bit-rate option, press the Audio Bit-rate softkey in the Audio A Menu.

  • Page 134: Input Level R Option

    Operating the Equipment Locally Input Level R Option NOTE… This option is not shown when the Coding Standard is MPEG Layer 2 (mono) or Dolby Digital (AC-3) (1/0). This option indicates the input level of the right audio channel. It is for status only and cannot be changed.

  • Page 135: Lip Sync Offset Option

    Lip Sync Offset Option NOTE… This option is only available if the Auto Lip Sync option is set to On. To access the Lip Sync Offset option, press the Lip Sync Offset softkey in the Audio A Menu. Table 4.48: Lip Sync Offset Options Valid Input Range Min: Max:...

  • Page 136: Clip Level Option

    Operating the Equipment Locally Clip Level Option To access the Clip Level option, press the Clip Level softkey in the Audio A Menu. This screen enables the audio clipping level to be set. NOTES… This option is only shown when the Coding Standard is MPEG Layer 2, Linear PCM or Dolby Digital (AC-3).

  • Page 137: Smpte 302M Standard Option

    SMPTE 302M Standard Option NOTES… This option is only shown when the Coding Standard is Linear PCM or Dolby E Pass-Thru. Problems may be experienced with some Receivers if the Encoder and Decoder are not using the same version of SMPTE 302M specification, e.g. either 1998 or 2000. The Encoder can be set up to work in either standard.

  • Page 138: Dialogue Level Option

    Operating the Equipment Locally Table 4.55: Bit Stream Mode Options Selected Option Complete Main Music & Effects Visually impaired Hearing impaired Dialogue Commentary Emergency Voice Over/Karaoke Dialogue Level Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the Dialogue Level option, press the Dialogue Level softkey in the Audio A Menu.

  • Page 139: Production Info Option

    Production Info Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the Production Info option, press the Production Info softkey in the Audio A Menu. This indicates whether the Mixing Level and Room Type parameters exist within the bit-stream.

  • Page 140: Copyright Option

    Operating the Equipment Locally Copyright Option NOTE… This option is shown when the Coding Standard is Dolby Digital (AC-3) or MPEG Layer 2. To access the Copyright option, press the Copyright softkey in the Audio A Menu. This indicates whether the information in the bit-stream is shown to be protected by copyright.

  • Page 141: Rf Protection Option

    RF Protection Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the RF Protection option, press the RF Protection softkey in the Audio A Menu. The option can be turned On (with RF Protection) or Off (without).

  • Page 142: Low Pass Filter Option

    Operating the Equipment Locally Low Pass Filter Option NOTE… This option is only shown when the Coding Standard is Dolby Digital (AC-3). To access the Low Pass Filter option, press the Low Pass Filter softkey in the Audio A Menu. This parameter is used to activate a low-pass filter with a cut-off near the specified audio bandwidth that is applied to the main input channels.

  • Page 143: Audio Languages Menu

    4.9.3 Audio Languages Menu The Audio Languages Menu is selected from the Audio Menu by pressing the Audio Languages softkey. This menu permits the selection of languages used in the MPEG broadcast. English is the default language and cannot be changed. Those other languages which have an asterisk (*) next to them are selected for use, those without an asterisk are not.

  • Page 144: Output Format Option

    Operating the Equipment Locally Table 4.65: Output Source Options Selected Option SDI Embedded (1-4) XLR Input (Monitor) Output Format Option To access the Output Format option, press the Output Format softkey in the Audio XLR Menu. Table 4.66: Output Format Options Selected Option Analogue Digital...

  • Page 145: Encoding Option

    Setup Menu Data Menu Data A - RS232... Data B - RS422... Data X A - RS232... Data X B - RS422... only shown if M2/EOM2/DAT option fitted Data X B - RS422 Menu Encoding Bit-rate RS422 PID Hardware Release Software Release Shaded options are showing status and cannot be changed.

  • Page 146: Rs232 Pid Option

    Operating the Equipment Locally Table 4.68: Baud Rate Options Selected Option 1200 2400 4800 RS232 PID Option The RS232 PID option is selected from the Data A - RS232 Menu by pressing the RS232 PID softkey. The option is used for entering or updating data PIDs.

  • Page 147: Bit-Rate Option

    Bit-rate Option To access the Bit-rate option, press the Bit-rate softkey in the Data B - RS422 Menu. This enables the bit-rate of the RS-422 synchronous data channel to be set. Table 4.70: Bit-rate Options Selected Option Settings cycle from 56 to 1792 in steps of 56 then from 64 to 2048 in steps of 64, then back to 56 RS422 PID Option The RS422 PID option is selected from the Data B - RS422 Menu by...

  • Page 148: Data Xa - Rs232 Menu (When M2/Eom2/Dat Fitted)

    Operating the Equipment Locally 4.10.4 Data XA - RS232 Menu (When M2/EOM2/DAT Fitted) Overview NOTE… In the Data XA - RS232 Menu, X = the number of the option slot that the module fits into. See Section 4.10.2, Data A - RS232 Menu, for the following options: ·...
  • Page 149 Output Format... Output Format... OFDM Modulator Satellite Modulator OFDM Modulator Menu Output Bandwidth Modulation Mode Guard Interval FEC Rate Transmission Spectral Pol Centre Frequency IF Output Frequency Bit-rate (188) Bit-rate (204) OFDM S/W Release Output Format... IP Streamer IP Streamer Menu Own IP Address Network Mask...

  • Page 150: 4.11.2 Output Format Option

    Operating the Equipment Locally 4.11.2 Output Format Option To access the Output Format option, press the Output Format softkey in the Output Menu. The menus available depend upon which option cards are fitted to the unit. If the Output Format option = ASI then the following menu option is Delivery Descriptor, otherwise it is the menu associated with the output format selected, i.e.

  • Page 151: Channel Option

    Table 4.72: Band Plan Options Selected Option Australia Europe VHF Europe CATV Italy Morocco New Zealand China OIRT Channel Option To access the Channel option, press the Channel softkey in the Delivery Descriptor Menu. Each channel number corresponds to a particular frequency (see Annex F, Band Plans).

  • Page 152: Modulation Type Option

    Operating the Equipment Locally NOTE… This option is status only unless Manual has been selected in the Band Plan option. Table 4.75: Bandwidth Options Selected Option 6 MHz 7 MHz 8 MHz 10 MHz 12 MHz Modulation Type Option To access the Modulation Type option, press the Modulation Type softkey in the Delivery Descriptor Menu.

  • Page 153: Guard Interval Option

    If the Hierarchy option is set to Alpha=n, then the FEC (HP) and FEC (LP) parameters provide two levels of modulation. Transmission starts with the code rate for the HP level of modulation and ends with the code rate for the LP level. The screen for the FEC (LP) option is the same except that (LP) replaces (HP).

  • Page 154: 4.11.6 Descriptor Type = Cable

    Operating the Equipment Locally Table 4.81: Other Frequency Options Selected Option None in use 4.11.6 Descriptor Type = Cable Frequency Option See Frequency Option on page 4-73. Modulation Type Option To access the Modulation Type option, press the Modulation Type softkey in the Delivery Descriptor Menu.

  • Page 155: Symbol Rate Option

    Table 4.84: FEC (Inner) Options Selected Option No conv. coding Symbol Rate Option To access the Symbol Rate option, press the Symbol Rate softkey in the Delivery Descriptor Menu. Table 4.85: Symbol Rate Options Valid Input Range Min: 0.4688 Msym/s Max: 30.0000 Msym/s Step Size: 0.0001 Msym/s...

  • Page 156: Orbital Position Option

    Operating the Equipment Locally Orbital Position Option To access the Orbital Position option, press the Orbital Position softkey in the Delivery Descriptor Menu. This enables the orbital position of the satellite to be specified. Table 4.87: Orbital Position Options Valid Input Range Min: 0.0°...

  • Page 157: If Power Option

    IF Power Option To access the IF Power option, press the IF Power softkey in the Satellite Modulator Menu. Table 4.90: IF Power Options Valid Input Range Min: –20 dBm Max: 5 dBm IF Frequency Option To access the IF Frequency option, press the IF Frequency softkey in the Satellite Modulator Menu.

  • Page 158: Symbol Rate Option

    Operating the Equipment Locally Symbol Rate Option To access the Symbol Rate option, press the Symbol Rate softkey in the Satellite Modulator Menu. Table 4.93: Symbol Rate Options Valid Input Range Min: Max: Step Size: Min (Low Sym Rate): Min: Max: Step Size: FEC Rate Option...

  • Page 159: Tx Bandwidth Factor Option

    Tx Bandwidth Factor Option To access the Tx Bandwidth Factor option, press the Tx Bandwidth Factor softkey in the Satellite Modulator Menu. This option is used to calculate the Tx Bandwidth based upon the Symbol Rate. Bandwidth = Factor x Symbol Rate Table 4.95: Tx Bandwidth Factor Options Valid Input Range Min:...

  • Page 160: Sat Deliv Freq Option

    Operating the Equipment Locally Sat Deliv Freq Option To access the Sat Deliv Freq option, press the Sat Deliv Freq softkey in the Satellite Modulator Menu. Table 4.98: Sat Deliv Freq Options Valid Input Range Min: 0.0000 GHz Max: 999.9999 GHz Step Size: 0.0001 GHz Sat Orb Pos Option To access the Sat Orb Pos option, press the Sat Orb Pos softkey in the...

  • Page 161: Polarisation Option

    Polarisation Option To access the Polarisation option, press the Polarisation softkey in the Satellite Modulator Menu. This enables the polarisation of the satellite transponder to be specified. Table 4.101: Polarisation Options Selected Option Linear - Horizontal Linear - Vertical Circular - Left Circular - Right Status Only Options for the Satellite Modulator Menu The following options are status only and cannot be changed.

  • Page 162: Frequency Option

    Operating the Equipment Locally Frequency Option To access the Frequency option press the Frequency softkey in the Satellite Modulator Menu. Table 4.103: Frequency Options Valid Input Range Min: 950 MHz Max: 1750 MHz Modulation Option To access the Modulation option, press the Modulation softkey in the Satellite Modulator Menu.

  • Page 163: Preset Pwr Norm Option

    Preset Pwr Norm Option Refer to Preset Pwr Norm Option on page 4-81 for details. Upconverter Power To access the Upconverter Power option, press the Upconverter Power softkey in the Satellite Modulator Menu. This option allows the +24 Vdc power on the L-Band Modulator Main output to be either Enabled or Disabled.

  • Page 164: Bandwidth Option

    Operating the Equipment Locally Bandwidth Option To access the Bandwidth option, press the Bandwidth softkey in the OFDM Modulator Menu. Table 4.104: Bandwidth Options Selected Option 6 MHz 7 MHz 8 MHz Modulation Mode Option To access the Modulation Mode option, press the Modulation Mode softkey in the OFDM Modulator Menu.

  • Page 165: Transmission Option

    Transmission Option To access the Transmission option, press the Transmission softkey in the OFDM Modulator Menu. Table 4.108: Transmission Options Selected Option 2k Mode 8k Mode Spectral Pol Option To access the Spectral Pol option, press the Spectral Pol softkey in the OFDM Modulator Menu.

  • Page 166: Own Ip Address Option

    Operating the Equipment Locally 4.11.11 Output Format = IP Streamer (3.1 and later) Own IP Address Option To access the Own IP Address option, press the Own IP Address softkey in the IP Streamer Menu. This is the local IP address associated with the 100 Mbit/s Ethernet video output interface.

  • Page 167: Multicast Ip Address Option

    Multicast IP Address Option This option is not used. Time To Live Option To access the Time To Live option, press the Time To Live softkey in the IP Streamer Menu. This is the Time-to-Live setting as specified in RFC-791. The Time-to-Live setting is decremented by one for each Router hop the IP frame does.

  • Page 168: 4.12.3 Mux Output, With Remux Card

    Operating the Equipment Locally 4.12.3 Mux Output, With Remux Card To obtain an output when a Remux card is fitted, set the options in the following menus: · Host Bit-rate Option on page 4-97 · Remux Module menu – see Section 4.13.3, Remux Module Menu ·...
  • Page 169 Menu Mux... Remux Module... 1.Service 2.Service (1)... up to 13.Service 1[Mdb].Service... up to 4[Mdb].Service... This menu is mainly for TANDBERG Television use for testing purposes. 1-4[Mdb].Service Menu Name Service Id Service Type PMT PID PCR PID Video Audio A Audio B...
  • Page 170 Operating the Equipment Locally Setup Menu Menu Mux... Remux Module... 2.Service 2, 7 3.Program 2 (1)... up to xxxx.Service Bit-Rate (204) is only available when the Packet Length is set to 204. This name changes to be the same as the Service Name. There could be more menus, depending upon the number of inputs to the Remux card.

  • Page 171: Bit-Rate (188) And Bit-Rate (204) Option

    4.12.6 Bit-rate (188) and Bit-rate (204) Option NOTE… If the Packet Length option is set to 188 bytes then only the Bit-rate (188) option is displayed. If the Packet Length option is set to 204 bytes then both the Bit-rate (188) and Bit-rate (204) options are displayed.

  • Page 172: 4.12.9 Fpga Firmware

    Page 4-94 Description Encoder output is not scrambled. Encoder output is scrambled using the fixed RAS key assigned by TANDBERG TV, and preprogrammed into the Encoder. Encoder output is scrambled using the fixed second RAS key assigned by TANDBERG TV, and preprogrammed into the Encoder.

  • Page 173: Overview

    Enter up to seven digits using the keypad, then press the Enter softkey to accept the scrambling code. If less then seven digits are entered, they are prefixed with 0’s (zero) to give a seven digit code. 4.12.14 BISS Options Enabled Overview BISS Mode 1 uses a fixed scrambling key, known as the Session Word, to encrypt the transport stream.

  • Page 174: Session Word Option

    Operating the Equipment Locally To access the BISS in the Mux Menu. This enables the scrambling key used in BISS Key Entry scrambling mode to be set (see the Scramble Option). The same scrambling code must be used at the receive end to unscramble the transmission.

  • Page 175: Remux

    4.13 Remux 4.13.1 Introduction If the Remux option module M2/EOM2/REMUX is fitted, there is an additional item in the Mux Menu (see Figure 4.18) and a further Remux Module Menu and 1.Service Menu. 4.13.2 Addition to Mux Menu When Remux Fitted Host Bit-rate Option NOTE…...

  • Page 176: Packet Length Option

    Operating the Equipment Locally NOTE… If Intelligent mode is selected, the Action On PID Error option (see page 4-30) in the Setup/System/Advanced Menu must be set to Auto Correct. If Dumb mode is selected, the Action On PID Error option must be set to Raise Alarm. Packet Length Option This option indicates the packet length.

  • Page 177: Source (Bnc) Option

    Table 4.120: Output Options Selected Option On (RAS) On (BISS Mux Key) On (BISS Mode 1) On (BISS-E) Source (BNC) Option This option indicates the source of the input. It is for status only. Table 4.121 indicates what is shown for the various inputs. Table 4.121: Source (BNC) Options Selected Option 1, 2, 3...

  • Page 178: Name Out Option

    Operating the Equipment Locally Name Out Option To access the Name Out option press the Name Out softkey in the 1.Service Menu. This option allows the service output name to be changed. Service Prov (In) Option NOTE… This option is only shown on an incoming Service menu (2-13.Service Menu). This option indicates the input service provider’s name.

  • Page 179: Major Channel Option

    Major Channel Option NOTE… This option is only shown in ATSC mode. To access the Major Channel option, press the Major Channel softkey in the 2.Service Menu. This enables the major channel to be specified. Minor Channel Option NOTE… This option is only shown in ATSC mode. To access the Minor Channel option, press the Minor Channel softkey in the 2.Service Menu.

  • Page 180: Pmt Pid Option

    Operating the Equipment Locally PMT PID Option NOTE… This option is status only for the Host Encoder but can be changed for incoming services. To access the PMT PID option, press the PMT PID softkey in the 2.Service Menu. This shows the Program Map Table Packet Identifier. Table 4.124: PMT PID Options Selected Option Min:...

  • Page 181: Ecm (Ca) Pid Option

    ECM (CA) PID Option NOTE… This option is status only for the Host Encoder but can be changed for incoming services. Available from Build version 2.2.0 and later. To access the ECM (CA) PID option, press the ECM (CA) PID softkey in the 2.Service Menu.

  • Page 182: Data (Type Of Data) Option

    Operating the Equipment Locally Table 4.129: Audio (Type of Audio) Options Selected Option Min: Max: 8190 (1FFEh) Step Size: Data (Type of Data) Option NOTES… This option is status only for the Host Encoder but can be changed for incoming services. Available from Build version 2.2.0 and later.

  • Page 183: Ird Menu (3.1 And Later)

    4.14 IRD Menu (3.1 and later) 4.14.1 Overview NOTE… This option is available in Build version 3.1.0 and later. The IRD Menu is selected from the Setup Menu by pressing the IRD softkey. The menu controls the internal receiver decoder (IRD), if it is fitted. The IRD consists of the SD Decoder option M2/EOM2/DEC and either of the following demodulator options, M2/EOM2/QPSKDEMOD or M2/EOM2/SATDEMOD.
  • Page 184 Operating the Equipment Locally Setup Menu Available from Build Version 3.1.0 and later. Menu IRD Mode IRD TS Source IRD Demod (If Fitted)... Service List... IRD Video... IRD Audio1... IRD Audio2... IRD CA... IRD VBI... IRD Data... IRD System Status... IRD Data System Menu...

  • Page 185: 4.14.4 Ird Demod Menu

    4.14.4 IRD Demod Menu Frequency Option To access the Frequency option, press the Frequency softkey in the IRD Demod Menu. This value is either the L-Band frequency for the demodulator to tune to if the LNB option is set to ‘Direct RF’, or it is the satellite frequency to tune to if the LNB option is set to ‘Active’.

  • Page 186: Polarisation Option

    Operating the Equipment Locally Polarisation Option To access the Polarisation option, press the Polarisation softkey in the IRD Demod Menu. Table 4.136: Polarisation Options Selected Option Horizontal Vertical Sat Input Option To access the Sat Input option, press the Sat Input softkey in the IRD Demod Menu.

  • Page 187: Lnb Lo Freq Option

    LNB Lo Freq Option To access the LNB Lo Freq option, press the LNB Lo Freq softkey in the IRD Demod Menu. This value should be set to the LNB’s lower local oscillator frequency. If the LNB has only one local oscillator then both the LNB Lo and LNB Hi Freq options should be set to that value.

  • Page 188: Status Only Options For The Ird Demod Menu

    Operating the Equipment Locally Status Only Options for the IRD Demod Menu The following options are for status only and cannot be changed. · LNB Fault Status · Demod Status · Part Number · Code Version 4.14.5 Service List Menu To access the Service List Menu, press the Service List softkey in the IRD Menu.

  • Page 189: 525 Line Composite Option

    525 Line Composite Option To access the 525 Line Composite option, press the 525 Line Composite softkey in the IRD Video Menu. Table 4.145: 525 Line Composite Options Selected Option 525 NTSC M 525 NTSC M No Pedestal 525 PAL M 625 Line Composite Option To access the 625 Line Composite option, press the 625 Line Composite softkey in the IRD Video Menu.

  • Page 190: Edh Enable Option

    Operating the Equipment Locally EDH Enable Option To access the EDH Enable option, press the EDH Enable softkey in the IRD Video Menu. This allows the pass-through of Error Detection Hierarchy (EDH) to be either enabled or disabled. Table 4.149: EDH Enable Options Selected Option True False...

  • Page 191: 4.14.7 Ird Audio 1 And Audio 2 Menus

    4.14.7 IRD Audio 1 and Audio 2 Menus NOTE… The menu structures are identical for Audio Channel 1 and Audio Channel 2. Audio Stream This shows the currently selected audio stream. To access the Audio Stream option, press the Audio Stream softkey in the IRD Audio Menu. It is then possible to select the audio stream to be decoded from the audio streams present in the currently selected service.

  • Page 192: Mute State Option

    Operating the Equipment Locally Table 4.153: Downmix Mode Options Selected Option Stereo Pair Dolby Pro Logic Stereo Mute State Option To access the Mute State option, press the Mute State softkey in the IRD Audio Menu. The Mute State can either be set ‘On’, i.e. no audio output, or ‘Off’, audio output present.

  • Page 193: 4.14.8 Ird Ca Menu

    Encoder. DSNG Key Option To access the DSNG Key option, press the DSNG Key softkey in the IRD CA Menu. This sets the TANDBERG RAS DSNG key, which is a seven digit number. BISS Mode Option To access the BISS Mode option, press the BISS Mode softkey in the IRD CA Menu.

  • Page 194: 4.14.9 Ird Vbi Menu

    Operating the Equipment Locally 4.14.9 IRD VBI Menu VITS Enable Option To access the VITS Enable option, press the VITS Enable softkey in the IRD VBI Menu. Table 4.156: VITS Enable Options Selected Option Disabled CCIR FCC/UK CCVC Enable Option To access the CCVC Enable option, press the CCVC Enable softkey in the IRD VBI Menu.

  • Page 195: Ird Data Menu

    4.14.10 IRD Data Menu Async Stream Option To access the Async Stream option, press the Async Stream softkey in the IRD Data Menu. This is used to select the asynchronous data stream to be decoded, from those present in the selected service. Async Baudrate This gives the baud-rate of the selected asynchronous data stream.

  • Page 196: Teletext Stream Option

    Operating the Equipment Locally Teletext Stream Option To access the Teletext Stream option, press the Teletext Stream softkey in the IRD Data Menu. This is used to select the Teletext stream to be decoded, from those present in the selected service. 4.14.11 IRD System Status Menu The IRD System Status Menu has a number of options which are status only and cannot be changed:...

  • Page 197: Restore Defaults

    Restore Defaults To access the Restore Defaults option, press the Restore Defaults softkey in the Error Masks Menu. This sets alarm, fail and error messages to the factory defaults. Errors Menu Active Errors Error Masks... Quit Figure 4.21: Menu Hierarchy – Error Masks Menu 4.16 Diagnostics Menu See Chapter 6, Preventive Maintenance and Fault-finding for information...

  • Page 198: 4.17.3 Active Configuration

    Operating the Equipment Locally The Encoder normally holds the following configurations: · One Active Configuration (it runs the Encoder) · Sixteen User configurations (in the User FLASH) · Sixteen Backup configurations (in Backup FLASH) · Sixteen 525 factory default configurations ·...

  • Page 199: 4.17.5 Backup Configurations

    4.17.5 Backup Configurations Backup FLASH stores a copy of each of the 16 user configurations when you select Store Configs in Backup, you will be asked for the password here. If unsure of the user configurations or they become inadvertently modified, the user configurations can be returned to a known state at any time by the command Load Configs from Backup.

  • Page 200: 4.17.9 Load Active Config Option

    Operating the Equipment Locally This menu provides options for loading and storing predefined configurations and updating and restoring backup configurations. 4.17.9 Load Active Config Option To access the Load Active Config option, press the Load Active Config softkey in the Config Menu. Use the softkeys to select the required configuration to be loaded.
  • Page 201 4.17.13 Factory 525 Defaults Option This option enables the 16 user configurations to be overwritten by the factory default settings for 525 line/29.97 Hz video operation. Press the Factory 525 Defaults softkey in the Config Menu. NOTE… The Factory 525 Defaults option is activated immediately. 4.17.14 Factory 625 Defaults Option The Factory 625 Defaults option is very similar to the Factory 525 Defaults option, except that it overwrites the 16 user configurations with the factory...
  • Page 202 Operating the Equipment Locally BLANK Page 4-124 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 203 Contents 5.1 Introduction ... 5-3 5.2 How to Set Up Internet Explorer For the Web Browser Interface... 5-3 5.3 Web Browser Interface Options ... 5-6 5.4 Cloning a File ... 5-11 List of Figures Figure 5.1: Internet Options Dialog Box ... 5-3 Figure 5.2: Settings Dialog Box...
  • Page 204 Web Browser Interface BLANK Page 5-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 205 Introduction There is a range of diagnostic and other utilities that can be accessed via a web browser, such as Internet Explorer. Before these can be accessed it is important to ensure that the Internet Explorer is correctly set up for the web browser.
  • Page 206 Web Browser Interface Figure 5.2: Settings Dialog Box 4. For Check for newer versions of stored pages, select Every visit to the page or any changes made to the pages will not be displayed. Click OK to save the changes and return to the Internet Options dialog box.
  • Page 207 6. Click LAN Settings to open the Local Area Network (LAN) Settings dialog box (see Figure 5.4). Figure 5.4: Local Area Network (LAN) Settings Dialog Box 7. Click Advanced to open the Proxy Settings dialog box (see Figure 5.5). Figure 5.5: Proxy Settings Dialog Box Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 Web Browser Interface...
  • Page 208 Web Browser Interface 8. In the Exceptions area type the IP address of the Encoder. 9. Click OK as many times as necessary to close all dialog boxes until only the Internet Explorer window is open. For Internet Explorer version 4 the same selections must be made, but the process starts from the View menu.
  • Page 209 Figure 5.7: Build Info – Version Numbers Figure 5.8: Build Info - Release Notes Option 2, Tools · Figure 5.9 when clicking Bandwidth Calculations, OFDM Bit-rate Calculations · Figure 5.10 when clicking Bandwidth Calculations, RF Calculations · Figure 5.11 when clicking OSD Toolkit ·...
  • Page 210 Web Browser Interface Bandwidth Calculations, OFDM Bit-rate Calculations - The Bit Rate Calculator (see Figure 5.9) allows you to enter various parameters and the optimal bit-rate (Mbit/s) is automatically calculated for 204 bytes and 188 bytes. Figure 5.9: Tools - Bandwidth Calculations- OFDM Bit-rate Calculations Bandwidth Calculations, RF Calculations - The Modulation Help (see Figure 5.10) allows you to see the difference that various parameters have upon the symbol rate and bandwidth.
  • Page 211 Option 3, Customer Support - has the contact information for Customer Services in various countries throughout the world. Option 4, Front Panel - is for TANDBERG Television internal use only. Option 5, Backplane - displays a screen similar to: ·...
  • Page 212 Base (MIB ) files to be downloaded from the Encoder to the PC. The password is available from TANDBERG Television Customer Services under a non-disclosure agreement (NDA). A definition of management items for some network component that can be accessed by a network manager. A MIB includes the names of objects it contains and the type of information retained.
  • Page 213 A particularly useful feature of the Encoder is the ability to extract a clone file. This can be sent to TANDBERG Television and used to configure other Encoders to exactly the same specification. It is very useful when trying to reproduce a fault and also for restoring a machine after repair.
  • Page 214 Web Browser Interface BLANK Page 5-12 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 215 Checks on Completion of Servicing... 6-4 6.3 Maintenance and Support Services ... 6-4 6.3.1 Introduction... 6-4 6.3.2 Warranty ... 6-4 6.3.3 Levels of Continuing TANDBERG Television Service Support ... 6-4 6.4 Errors and Diagnostics Menus – When to Use Them ... 6-5 6.4.1 Error Messages ...
  • Page 216 Preventive Maintenance and Fault-finding BLANK Page 6-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...

  • Page 217: Introduction

    DO NOT ATTEMPT TO SERVICE THIS PRODUCT AS OPENING OR REMOVING COVERS MAY EXPOSE DANGEROUS VOLTAGES OR OTHER HAZARDS. REFER ALL SERVICING TO SERVICE PERSONNEL WHO HAVE BEEN AUTHORISED BY TANDBERG TELEVISION. Unplug the equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions: 1.

  • Page 218: Replacement Parts

    There is a customer service centre open round the clock, every day of the year, in your time zone. TANDBERG’s years of design and support experience enable it to offer a range of service options that will meet your needs at a price that makes sense.

  • Page 219: Errors And Diagnostics Menus - When To Use Them

    Errors and Diagnostics Menus – When to Use Them 6.4.1 Error Messages Summary Screen Ops ... Cfgs More ... Quit Figure 6.1: Finding the Errors Menu Investigate any run-time errors by pressing the Active Errors softkey in the Errors Menu (see Figure 6.1). Current errors are displayed. NOTES…...

  • Page 220: Lcd Display Test

    Preventive Maintenance and Fault-finding Summary Screen Ops ... Cfgs More ... Quit Figure 6.2: Finding the Diagnostics Menu LCD Display Test Press the LCD Display softkey to access the option and then press any key to cycle through the test patterns and to return to the menu. Keyboard Test Press the Keyboard softkey to access the option and then press each softkey and keypad key in turn.

  • Page 221: Buzzer Test

    DO NOT REMOVE THE COVERS OF THIS EQUIPMENT. HAZARDOUS VOLTAGES ARE PRESENT WITHIN THIS EQUIPMENT AND MAY BE EXPOSED IF THE COVERS ARE REMOVED. ONLY TANDBERG TELEVISION TRAINED AND APPROVED SERVICE ENGINEERS ARE PERMITTED TO Do not remove the covers of this equipment. Unauthorised maintenance or the use of non-approved replacements may affect the equipment specification and invalidate any warranties.

  • Page 222: User Accessible Fuse Replacement

    Preventive Maintenance and Fault-finding 2. Confirm that the equipment hardware configuration is suitable for the purpose and has been correctly installed and connected (see Chapter 2, Installing the Equipment). 3. Confirm that inappropriate operator action is not causing the problem, and that the equipment software set-up is capable of performing the task being asked of it.

  • Page 223: Video Fault-Finding

    AC Power Inlet Figure 6.3: Orientation of Fuse Carrier If the replacement fuse also blows, do not continue. Disconnect the equipment and contact Customer Services for advice. 6.5.4 Video Fault-finding Fault Symptoms Table 6.1: Video Fault-finding Problem Video input lock error Video - wrong line standard VCM stopped Bad parameters...

  • Page 224: Audio Fault-Finding

    Preventive Maintenance and Fault-finding 6.5.5 Audio Fault-finding If having problems when using the Dolby E Pass-through coding mode then refer to Annex G, Audio Modes, for information about using this mode. 6.5.6 Mux Fault-finding If there is no output from the ASI connectors, check the following: 1.

  • Page 225: Power Supply Problems/Green Led On Front Panel Unlit

    DO NOT ATTEMPT TO SERVICE THE POWER SUPPLY UNIT AS OPENING OR REMOVING COVERS MAY EXPOSE DANGEROUS VOLTAGES OR OTHER HAZARDS. REFER ALL SERVICING TO SERVICE PERSONNEL WHO HAVE BEEN AUTHORISED BY TANDBERG TELEVISION. Use the following techniques to fault-find the Encoder according to the observed symptom(s) when a power supply failure is suspected.

  • Page 226: Disposing Of This Equipment

    Preventive Maintenance and Fault-finding Table 6.4: Fans Not Working/Overheating Step Action Check Fan Rotation. Inspect the fans located at the sides of the enclosure. Are the fans rotating? Check Base Board temperature and fan (see the Build Menu in Figure 4.9). Disposing of This Equipment 6.9.1 General...
  • Page 227 The following list covers most of the abbreviations, acronyms and terms as used in TANDBERG Television Limited Manuals. All terms may not be included in this manual. Micrometre (former name - micron): a unit of length equal to one millionth (10...
  • Page 228 Glossary B3ZS Bipolar with Three Zero Substitution: A method of eliminating long zero strings in a transmission. It is used to ensure a sufficient number of transitions to maintain system synchronisation when the user data stream contains an insufficient number of 1s to do so. B3ZS is the North American equivalent of the European HDB3. Backward Compatibility Refers to hardware or software that is compatible with earlier versions.
  • Page 229 Compression Reduction in the number of bits used to represent the same information. For the purposes of a broadcast system, it is the process of reducing digital picture information by discarding redundant portions of information that are not required when reconstituting the picture to produce viewing clarity. Compression allows a higher bite-rate to be transmitted through a given bandwidth.
  • Page 230 Group of Pictures: MPEG video compression works more effectively by processing a number of video frames as a block. The TANDBERG Television Encoder normally uses a 12 frame GOP; every twelfth frame is an I frame. Graphical User Interface: The use of pictures rather than just words to represent the input and output of a program.
  • Page 231 Intermediate Frequency: Usually refers to the 70 MHz or 140 MHz output of the Modulator in cable, satellite and terrestrial transmission applications. Interframe Coding Compression coding involving consecutive frames. When consecutive frames are compared, temporal redundancy is used to remove common elements (information) and arrive at difference information. MPEG-2 uses B and P frames, but since they are individually incomplete and relate to other adjacent frames, they cannot be edited independently.
  • Page 232 MCPC Multiple Channels Per Carrier. Multiplex Element Manager: A GUI based control system, part of the range of TANDBERG Television compression system control element products. The evolution 5000 MEM holds a model of the system hardware. Using this model, it controls the individual system elements to configure the output multiplexes from the incoming elementary streams.
  • Page 233 NVOD Near Video On Demand: Method of offering multiple showings of movies or events. The showings are timed to start at set intervals, determined by the broadcaster. Each showing of a movie or event can be sold to subscribers separately. NVRAM Non-volatile Random Access Memory: Memory devices (permitting random read / write access) that do not lose their information when power is removed.
  • Page 234 Random Access Memory: A volatile storage device for digital data. Data may be written to, or read from, the device as often as required. When power is removed, the data it contains is lost. Remote Authorization System: A TANDBERG TV proprietary public-key encryption system used to prevent unauthorized viewing of a TV programme or programmes.
  • Page 235 Service Information: Digital information describing the delivery system, content and scheduling (timing) of broadcast data streams. DVB-SI data provides information to enable the IRD to automatically demultiplex and decode the various streams of programmes within the multiplex. Specified in ISO/IEC 13818[1]. (DVB) Single Packet Burst Mode A burst of ASI bytes (either 188 or 204, depending on packet length) is contiguously grouped into an MPEG-2 Transport Stream packet.
  • Page 236 Glossary UART Universal Asynchronous Receiver Transmitter: A device providing a serial interface for transmitting and receiving data. Ultra High Frequency: A portion of the electromagnetic spectrum covering 300 MHz to 3000 MHz (3 GHz). Upconvert The process by which the frequency of a broadcast transport stream is shifted to a higher frequency range. Uplink The part of the communications satellite circuit that extends from the Earth to the satellite.
  • Page 237 Analogue and Digital Audio ...B-6 Embedded Audio (Via SDI)...B-8 B.2 Test Tones ...B-8 B.3 Outputs...B-9 B.3.1 IF Outputs (1U, E5714)...B-9 B.3.2 IF Outputs (E5740-IF)...B-10 B.3.3 L-Band Outputs (E5740-LBAND)...B-11 B.3.4 OFDM Modulator Outputs (E5750)...B-12 B.3.5 ASI Out 1, ASI Out 2, ASI Out 3 Outputs...B-12 B.4 Control and Monitoring...B-13...
  • Page 238 Table B.10: Embedded Audio Specification ... B-8 Table B.11: Test Tones Specification... B-8 Table B.12: IF OUT MAIN Specification (1U, E5714) ... B-9 Table B.13: IF Monitor Output Specification (1U, E5714) ... B-10 Table B.14: IF OUT MAIN Specification (E5740-IF)... B-10 Table B.15: IF OUT MONITOR Specification (E5740-IF)...

  • Page 239: Inputs

    Inputs B.1.1 Video Table B.1: Serial Digital Video Specification Item Safety status Connector designation Connector type Input standard (UK/EC) Input standard (USA) Cable length Recommended cable type Input level Return loss Input impedance H SYNC Table B.2: H SYNC Specification Item Safety status Connector designation...

  • Page 240: Analogue Video Specification

    Technical Specification Analogue Video Specification Table B.3: Analogue Video Specification Item Analogue input Connector designation Connector type Input level Return loss Input impedance NOTE… The inputs are isolated from the chassis to prevent 50 Hz/60 Hz hum. Encoder Settings for PAL/NTSC Video Performance Figures The Encoder settings for the PAL/NTSC video performance figures are shown in Table B.4.

  • Page 241: Ntsc Video Performance Figures

    Pattern VITS Line 17 VITS line 17 VITS Line 17 VITS Line 17 100% Luma Ramp 5-step staircase - modulated 5-step staircase - modulated 5-step staircase - modulation Flat field Red 75% Multiburst VITS line 18 NTSC Video Performance Figures Table B.6: NTSC System Video Performance Figures Pattern NTC-7 Composite...

  • Page 242: International Television Standards

    Technical Specification International Television Standards Table B.7 shows television standards appropriate to the Encoder. Table B.7: International Television Standards As indicated in Menus M Region Standard Lines / frame Fields / second Interlace Frames / second Lines / second Aspect ratio Video band (MHz) B.1.2 Audio...
  • Page 243 NOTES… Refer to Annex G, Audio Modes when using these coding standards. Problems may be experienced with some Receivers if the Encoder and Decoder are not using the same version of SMPTE 302M specification, e.g. either 1998 or 2000. The Encoder can be set up to work in either standard.

  • Page 244: Embedded Audio (Via Sdi

    Technical Specification Item Noise RMS A-weighted Unweighted User Levels @ 1 kHz (0 to 50 dB) +10 dB -10 dB -20 dB -30 dB -40 dB -50 dB Phase @ 0 dBs 40 Hz 100 Hz 315 Hz 1 kHz 6.3 kHz 10 kHz 15 kHz...

  • Page 245: Outputs

    Outputs B.3.1 IF Outputs (1U, E5714) Table B.12: IF OUT MAIN Specification (1U, E5714) Item Safety status: Connector designation: Connector type: Output impedance: Return loss: Output power: Power level stability: Signal type: Symbol-rate (minimum) Symbol rate (maximum) vs carrier frequency Fc:...

  • Page 246: If Outputs (E5740-If

    Technical Specification Table B.13: IF Monitor Output Specification (1U, E5714) Item Safety status: Connector designation: Connector type: Output impedance: Return loss: Output power: B.3.2 IF Outputs (E5740-IF) Table B.14: IF OUT MAIN Specification (E5740-IF) Item Safety status: Connector type: Connector designation:...

  • Page 247: L-Band Outputs (E5740-Lband

    Table B.15: IF OUT MONITOR Specification (E5740-IF) Item Safety status: Connector type: Connector designation: Output impedance: Output power: Return loss: B.3.3 L-Band Outputs (E5740-LBAND) Table B.16: L-Band Out Main Specification (E5740-Lband) Item Safety Status: Connector Type: Connector Designation: Output Impedance: Output Power: Power Level Stability: Return Loss:...

  • Page 248: Ofdm Modulator Outputs (E5750

    Technical Specification Table B.17: L-Band Monitor Output Specification (E5740-Lband) Item Safety Status: Connector Type: Connector Designation: Output Impedance: Output Power: Return Loss: B.3.4 OFDM Modulator Outputs (E5750) Table B.18: OFDM IF Out 1 Specification (E5750) Item Safety Status: Connector Type: Connector Designation: Output Impedance: Output Power:...

  • Page 249: Control And Monitoring

    Control and Monitoring B.4.1 Remote Control - Ethernet 1 and 2 Table B.21: Ethernet Specification Item Safety status Connector designation Connector type B.4.2 Local Control Local control is by means of the front panel keypad and LCD display. B.4.3 Alarm Table B.22: Alarm Specification Item Safety status...

  • Page 250: Data (Asynchronous

    Technical Specification B.4.6 RS-422 Data This provides an RS-422 synchronous, serial communications data input interface. Table B.24: RS-422 Data Specification Item Safety status Type Connector designation Connector type Clock frequencies Time-stamp Operation modes Page B-14 Specification SELV ITU-T V.11 (RS-422), synchronous serial data and external clock RS-422 DATA 15-way D-type female n x 64 kbit/s from 64 kbit/s to 2048 kbit/s (selectable)

  • Page 251: Power Supply

    Power Supply B.5.1 AC Power Input This equipment is fitted with an wide-ranging power supply. It is suitable for supply voltages of 100-120 Vac -10% +6% or 220-240 Vac -10% +6% at 50/60 Hz nominal. Table B.25: AC Power Supply Specification Item Power distribution system Connection to supply...

  • Page 252: Instruction Manual: Evolution 5000 E57Xx Dsng And Deng Voyager Encoder St.tm.e10076.3

    Technical Specification B.5.2 DC Power Input The power unit used in the Encoder is a soft-start type designed for use on dc supplies having a negative or positive earth (vehicle chassis) voltage supply in the range 12 to 36 Vdc. Table B.26: DC Power Supply Specification Item Rated Voltage:...

  • Page 253: Environmental Conditions

    Environmental Conditions Table B.28: Environmental Specification Item Operational Temperature Over temperature alarm generated at Under temperature alarm generated at Temperature checked All fans switched off at Half the fans switched off at All fans on at Relative humidity Cooling requirements Handling/movement Storage/Transportation Temperature...

  • Page 254: Emc

    Technical Specification B.8.2 The equipment has been designed and tested to meet the following: EN 55022 AS/NZS 3548 EN 61000-3-2 EN 61000-3-3 EN 55024:1998 B.8.3 Shock and Vibration The Encoder and Receiver chassis complies with the requirements of ETS 300-019-2-5 Table 2, for both non-operational and operational states, without any special mounting or casing requirements over and above the standard mounting requirements specified.

  • Page 255: Ce Marking

    The C-Tick mark was first affixed to this product in 2001. Cable Types The signal cable types (or similar) in Table B.29 are those recommended by TANDBERG Television in order to maintain product EMC compliance. Table B.29: Suitable Signal Cable Types Signal Type...

  • Page 256: Option Modules

    Technical Specification B.10 Option Modules B.10.1 M2/EOM2/AUDLIN Additional Audio and Linear PCM Option Module See Section B.1.2, Audio for details. B.10.2 M2/EOM2/DAT RS-232 and RS-422 Data Input Option Asynchronous Data Input A 9-way, D-type female connector provides an RS-232 asynchronous, serial communications data input interface.

  • Page 257: B.10.3 M2/Eom2/Remux Remux Option Module

    B.10.3 M2/EOM2/REMUX Remux Option Module Connectors NOTE… The M2/EOM2/REMUX Remux Option Module is supported by Encoder software version 2.2.0 and later. Table B.32: DVB ASI In 1, 2 and 3 Connector Item Safety status Connector designation Connector type Connector impedance Data coding Channel rate Specification...
  • Page 258 Technical Specification Table B.35: DVB ASI Out 1 - LED Indications Item Red LED Green LED Flash (1:3 mark:space) Flash (3:1 mark:space) Page B-22 Specification Output disabled Output enabled Output not in use 188 byte packets output 204 byte packets output Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...

  • Page 259: B.10.4 M2/Eom2/Xlr, Xlr Expander Card Option

    B.10.4 M2/EOM2/XLR, XLR Expander Card Option NOTE… The M2/EOM2/XLR, XLR Expander Card Option is supported by Encoder software version 3.0 and later. Table B.36: Analogue and Digital Audio (XLR Expander Card) Item Inputs Safety status Connector designation (inputs) Connector type Input standard (analogue) Clip Level Sampling rate...

  • Page 260: B.10.5 M2/Eom2/Dec, Sd Decoder Card Option

    Technical Specification B.10.5 M2/EOM2/DEC, SD Decoder Card Option NOTE… The M2/EOM2/DEC, SD Decoder Card Option is supported by Encoder software version 3.1 and later. Table B.37: ASI Output (SD Decoder) Item Safety Status: Connector Type: Connector Designation: Output Impedance: Data Coding: Channel Rate: Specification: Table B.38: Composite Video Output (SD Decoder)
  • Page 261 Table B.40: Audio Output (SD Decoder) Item Safety Status: Connector Type: Analogue Output Nominal Output Impedance: Clip Level: Sampling Rate: Digital Output Output Format: Output Impedance: Sampling Rate: Table B.41: Data Output (SD Decoder) Item Safety Status: Connector Type: Connector Designation: RS-232 Asynchronous Data Data Rate: Standards:...

  • Page 262: M2/Eom2/Qpskdemod, Qpsk

    Technical Specification B.10.6 M2/EOM2/QPSKDEMOD, QPSK Demodulator Card Option NOTE… The M2/EOM2/QPSKDEMOD, QPSK Demodulator Card Option is supported by Encoder software version 3.1 and later. Table B.42: IF In (QPSK Demodulator) Item Safety Status: Connector Type: Connector Designation: Input Impedance: Input Power: Input Frequency: Capture Range: Signal Type:...

  • Page 263: M2/Eom2/Satdemod, 16Qam

    B.10.7 M2/EOM2/SATDEMOD, 16QAM Demodulator Card Option NOTE… The M2/EOM2/SATDEMOD, 16QAM Demodulator Card Option is supported by Encoder software version 3.1 and later. Table B.44: L-band Inputs (16QAM Demodulator) Item Safety Status: Connector Type: Connector Designation: Input Impedance: Input Power (maximum): Capture Range: Signal Type: Symbol Rate:...
  • Page 264 Technical Specification BLANK Page B-28 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 265 Predefined User Configurations Contents C.1 Introduction ...C-3 C.2 525/625 Line Default Settings ...C-3 C.3 General Default Settings ...C-3 C.4 Predefined User Configurations ...C-7 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 Annex C List of Tables Table C.1: 525/625 Line Default Settings...C-3 Table C.2: Default Configuration Settings ...C-3 Table C.3: Predefined User Configurations...C-7 Page C-1...
  • Page 266 Predefined User Configurations BLANK Page C-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 267 PSIP Max PID Logical Channel Descriptor Logical Channel Logical Channel Descriptor Id Predefined User Configurations Default Value Config Name 300 s Auto (Temp. Controlled) Default Service Service Provider TANDBERG 0xFFFF 0x20 On (DVB compliant) BNC 1 0x1FD0 0x1FFE 0x83 Page C-3...
  • Page 268 Predefined User Configurations Module Mux: Video Preprocessor: Page C-4 Parameter Output Mode Setup Password Display Errors LCD Brightness SNMP Control During Initialisation System Type Action on PID Error MEM Error Handling IP Address Network Mask Gateway Address Serial Number (if non-zero used for MAC address) SNMP Master SNMP Trap Address...
  • Page 269 Coding Standard Source 6 dB Gain Silence Timeout Emphasis Language (L) Predefined User Configurations Default Value Ident Mode White Blue Semi-translucent TANDBERG MP@ML Standard Fixed and Seamless Modes Frame Only 720x576 IBBP 8 Mbit/s Line 23 Medium Medium None MPEG Layer 2...
  • Page 270 Predefined User Configurations Module Audio (Dolby Digital (AC-3)): Audio Musicam (MPEG-2): Linear PCM: RS-422 Data: RS-232 Data: Page C-6 Parameter Language (R) Clip Level Termination Auto Lip Sync Lip Sync Delay Lip Sync Offset Bit-rate Bit-stream Mode Coding Mode Copyright Original Dolby Surround Mode Dialogue Normalisation...
  • Page 271 Predefined User Configurations The predefined user configurations have the same settings as Table C.2 except for those differences shown in Table C.3. Table C.3: Predefined User Configurations Configuration Number Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 Service Name Variable Standard 6 MHz...
  • Page 272 Predefined User Configurations Configuration Number Page C-8 Service Name Variable Mega Low Delay 6 MHz Video Bit-rate Video Compression Mode Video Profile/Level GOP Structure Mega Low Delay 7.5 MHz Video Bit-rate Video Compression Mode Video Profile/Level GOP Structure Mega Low Delay 9 MHz Video Bit-rate Video Compression Mode Video Profile/Level...
  • Page 273 Languages are shown in alphabetical order. LANGUAGE ABBREVIATION AFRIKAANS ALBANIAN ARABIC BASQUE BRETON BULGARIAN CHINESE CZECH DANISH DUTCH ENGLISH ESTONIAN FINNISH FRENCH GAELIC GERMAN GREEK HUNGARIAN ICELANDIC INDONESIAN IRISH ITALIAN JAPANESE KOREAN LATVIAN LITHUANIAN Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 Language Abbreviations LANGUAGE...
  • Page 274 Language Abbreviations The following non-ISO languages are supported. NOTE… Only applicable for a transport stream going to an Alteia Receiver. REFERENCE ABBREVIATION MAIN INTERNATIONAL SOUND AUDIO 1 AUDIO 2 AUDIO 3 AUDIO 4 AUDIO 5 AUDIO 6 AUDIO 7 AUDIO 8 AUDIO 9 AUDIO 10 AUDIO 11...
  • Page 275 Creating and Downloading a Logo Contents E.1 Introduction ...E-3 E.2 Summary of Features...E-3 E.3 OSD Programs Built Into the Encoder ...E-3 E.4 Creating a Logo Using OSD Creator...E-5 E.5 Using OSD Creator ...E-5 E.5.1 Overview...E-5 E.5.2 Loading a .bmp File ...E-6 E.5.3 Creating Transparency ...E-6 Overview...E-6 Adding Transparency Manually ...E-7...
  • Page 276 Creating and Downloading a Logo BLANK Page E-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...

  • Page 277: Introduction

    To overlay the material with a logo, the logo must first be downloaded into the equipment using the Ethernet TFTP protocol. Once this has been done the logo can be enabled or disabled. Contact TANDBERG Television for further details. Summary of Features Up to 13 logos can be overlaid onto the active video.
  • Page 278 Creating and Downloading a Logo Figure E.1: Web Browser Interface The dialogue box, see Figure E.2, will be displayed. Figure E.2: File Download Dialogue Box Clicking on option Open this file from its current location and Clicking OK will open the .zip file, see Figure E.3. Clicking on option Save this file to disk will allow the user to install the files on their local drive and then open the .zip file as in Figure E.3.

  • Page 279: Creating A Logo Using Osd Creator

    Figure E.3: Files for OSD Creator and Loader Creating a Logo Using OSD Creator Osd Creator (creator.exe) is an application for creating logo files (.osd format) for use with the Osd Loader application (osd.exe) to download them to the Encoder. It accepts Windows Bitmap (.bmp) format files as input.

  • Page 280: Loading A .Bmp File

    Creating and Downloading a Logo An example of a logo is shown in Figure E.4. Zoom Left Mouse View Button Transparency Value Right Mouse Button Transparency Value Figure E.4: OSD Creator Screen Showing Example Logo E.5.2 Loading a .bmp File Select File/Open from the menu, and choose a file with a .bmp extension.

  • Page 281: Adding Transparency Manually

    Osd Creator uses a colour palette with a maximum of 256 entries. Each pixel in the image is mapped to an entry in the palette, which holds a value for the red, green and blue and transparency component. The transparency (or mix) is treated as a colour component, so for two colours with identical red, green and blue values, but different transparency levels, two entries will be generated in the palette.

  • Page 282: Editing The Palette

    Creating and Downloading a Logo Click the Key File toolbar button. Select the key file. The inactive area of the image should now be transparent (background-coloured). Change the background colour to verify that the correct area is transparent. Editing the Palette The palette may be displayed alongside the image by clicking the Show/Hide Palette toolbar button.

  • Page 283: Downloading A Logo Using Osd Loader

    Downloading a Logo Using OSD Loader The Osd Loader application (osd.exe) is used for downloading logo (.osd) files to the Encoder and controlling which are displayed. The application runs on a PC with Windows 95 or Windows NT. A network connection is required.

  • Page 284: Download An .Osd File

    Creating and Downloading a Logo The Resolution Mode must be set to match the video resolution being used. This adjusts the preview screen to the dimensions of the active video. Table E.1: Resolution Modes Resolution Mode 480p 576p 720p 1080i E.7.2 Download an .osd File Choose an On-screen Display file with the Choose File button.
  • Page 285 Field Line Figure E.6: 625 Line, OSD Co-ordinates in Active Picture Field Line Figure E.7: 525 Line, OSD Co-ordinates in Active Picture Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 OSD Loader Co-ordinates (139,44) Pixel OSD Loader Co-ordinates (148,44) 720 Pixels Digital Active Picture 702 Pixels Analogue Active Picture OSD Loader Co-ordinates (133,38)

  • Page 286: Show And Hide Regions

    Creating and Downloading a Logo E.7.3 Show and Hide Regions The Download button defines a Region in the Encoder, which remains until the Encoder is turned off, the Remove button is clicked, or the Region is Downloaded again. The Region may be in the Shown or Hidden state, which determines whether it appears in the video stream.

  • Page 287: Fault-Finding

    Fault-finding If there appears to be a problem creating or downloading a logo check the following: · If the Communications box reads "Error Creating Socket", there may be a problem with the PC's network set-up, or another application may be using the TFTP socket number. ·...
  • Page 288 Creating and Downloading a Logo BLANK Page E-14 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 289 Contents F.1 Channels and Centre Frequencies ... F-3 List of Tables Table F.1: Australia ... F-3 Table F.2: Europe VHF... F-4 Table F.3: EuropeCATV ... F-4 Table F.4: Italy... F-4 Table F.5: Morocco... F-4 Table F.6: New Zealand ... F-5 Table F.7: China ...
  • Page 290 Band Plans BLANK Page F-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 291 Channels and Centre Frequencies The Output Menu has options called Band Plan and Channel (see Chapter 4, Operating the Equipment Locally). Once a country has been selected in the Band Plan option then the required channel should be selected in the Channel option. Each channel number corresponds to a particular frequency.
  • Page 292 Band Plans Table F.2: Europe VHF Centre Channel Frequency in MHz 50.500 57.500 64.500 177.500 184.500 191.500 Table F.3: EuropeCATV Centre Channel Frequency in MHz 128.500 135.500 142.500 149.500 156.500 163.500 S 10 170.500 S 11 233.500 S 12 240.500 Table F.4: Italy Centre Channel...
  • Page 293 Table F.6: New Zealand Centre Channel Frequency in MHz 47.500 57.500 64.500 177.500 184.500 Table F.7: China Centre Channel Frequency Channel in MHz 52.500 60.500 68.500 80.000 88.000 171.000 179.000 187.000 195.000 203.000 211.000 219.000 474.000 482.000 490.000 498.000 506.000 Table F.8: OIRT Centre Channel...
  • Page 294 Band Plans Table F.9: Ireland Centre Channel Frequency in MHz 48.500 56.500 64.500 178.000 186.000 Table F.10: South Africa Centre Channel Frequency in MHz 178.000 186.000 194.000 202.000 210.000 Table F.11: French Overseas PIA Centre Channel Frequency in MHz 178.000 186.000 194.000 Table F.12: France...
  • Page 295 Table F.13: Japan Centre Channel Frequency Channel in MHz 93.000 99.000 105.000 173.000 179.000 185.000 191.000 195.000 201.000 J 10 207.000 J 11 213.000 J 12 219.000 473.000 479.000 485.000 491.000 497.000 Table F.14: USA Centre Channel Frequency Channel in MHz A 02 57.000 A 03...
  • Page 296 Band Plans Table F.15: CCIR Centre Channel Frequency in MHz 474.000 482.000 490.000 498.000 506.000 514.000 522.000 530.000 538.000 546.000 554.000 562.000 570.000 578.000 586.000 594.000 602.000 CCIR is now know as International Telecommunications Union-Radiocommunications Study Groups. Page F-8 Centre Channel Frequency Channel...
  • Page 297 Contents G.1 Analogue Audio... G-3 G.2 Digital Audio ... G-3 G.3 Embedded Audio on the SDI... G-4 G.4 Detail of Encoder Operation... G-4 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 Annex G Audio Modes List of Figures Figure G.1: Analogue Audio Modes ...G-3 Figure G.2: Digital Audio Modes...G-3 Figure G.3: Embedded Audio and Stereo Pairs ...G-5...
  • Page 298 Audio Modes BLANK Page G-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 299 Analogue Audio Figure G.1 shows the coding methods that may be used with the analogue audio input. Analogue Audio Independent of Encoder Clock Source Figure G.1: Analogue Audio Modes Digital Audio When a digital audio source is used, consideration must be given to the choice of clock source used by the Encoder.
  • Page 300 Audio Modes Embedded Audio on the SDI Figure G.3 shows the audio signal flow on the Base Board. While six audio stereo pairs are available, only two stereo pairs can be processed by the Base Board at any one time. Audio can be embedded on a SDI video feed.
  • Page 301 Audio groups taken from SDI. Group 1 Group 2 Group 3 Group 4 User DID Selection (Default=0x2FF) Group 1 Group 2 Group 3 Group 4 User DID Selection (Default=0x1FD) Stereo Pair A Interface Stereo Pair B Conversion 15-way D-type Connector Figure G.3: Embedded Audio and Stereo Pairs Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 302 Audio Modes BLANK Page G-6 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 303 Contents H.1 Introduction ...H-3 H.2 Dealing with Error Messages ...H-3 H.3 General Errors...H-4 H.4 Video Source Related Errors ...H-5 H.5 VBI Related Errors ...H-6 H.6 Remote Control Related Errors...H-6 H.7 Data Related Errors ...H-6 H.8 Video Encoder Related Errors ...H-7 H.9 Audio Related Errors...H-7 H.10 Satellite Modulator Related Errors ...H-8 H.11 Remux Related Errors...H-9...
  • Page 304 Error Messages BLANK Page H-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...

  • Page 305: Introduction

    DO NOT REMOVE THE COVERS OF THIS EQUIPMENT. HAZARDOUS VOLTAGES ARE PRESENT WITHIN THIS EQUIPMENT AND MAY BE EXPOSED IF THE COVERS ARE REMOVED. ONLY TANDBERG TELEVISION TRAINED AND APPROVED SERVICE ENGINEERS ARE PERMITTED TO If an error occurs in the DSNG Voyager Encoder (Encoder) then a message indicating the type of error is shown on the front panel display.

  • Page 306: General Errors

    Error Messages General Errors Table H.1: General Error Messages Error Message LCD Not Found Temp Sensor No Pulse Temp Sensor Bad CRC Temp Sensor Bad Data Temp Sensor Busy Temp Sensor Comms PSU Sensor Real Time Clock Ethernet Comms FPGA Boot Fail Over Temperature Under Temperature Over Voltage (5V)

  • Page 307: Video Source Related Errors

    Video Source Related Errors Table H.2: Video Source Error Messages Error Message Comms Error Video Lock (Composite) Video Lock (SDI) Video Line Standard EDH Full Field Error EDH Full Field Unknown Error EDH Full Field Error Already EDH Picture Error EDH Picture Error Unknown Err EDH Picture Error Already EDH Anc.

  • Page 308: Vbi Related Errors

    Error Messages VBI Related Errors Table H.3: VBI Error Messages Error Message Duplicate VBI PID Invalid VBI PID Duplicate Teletext PID Invalid Teletext PID Closed Caption (Line 21) Closed Caption (Ext. Data) Neilson/AMOL 1 Detection Neilson /AMOL 11 Detection VPS Detection WSS Detection VITC Detection Video Index Detection...

  • Page 309: Video Encoder Related Errors

    Video Encoder Related Errors Table H.6: Video Encoder Error Messages Error Message Comms Error Config Update VCM Stopped Bad Parameters Duplicate PID Invalid PID VBI, Bit-rate too low VBI Hor Res too low Mux Bit-rate too low No interrupt DSP Overrun Boot Fail Bad Frame Rate Rate Buffer OF/UF...

  • Page 310: Satellite Modulator Related Errors

    Error Messages Error Message Level Clipping Left Level Clipping Right Embedded Source 1 Embedded Source 2 Embedded Source 3 Embedded Source 4 AC-3 Input Invalid No Digital Input Mux FIFO Overflow Duplicate PID Invalid PID Mux Bit-Rate too low Audio Un-Calibrated H.10 Satellite Modulator Related Errors Table H.8: Satellite Modulator Error Messages...

  • Page 311: Remux Related Errors

    H.11 Remux Related Errors Table H.9: Remux Error Messages Error Message Overflow On Input 1 Overflow On Input 2 Overflow On Input 3 Overflow Motherboard O/P Remux Card Stopped Motherboard O/P TS Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3 Action to Take Reduce incoming bit-rate.
  • Page 312 Error Messages BLANK Page H-10 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 313 When this equipment is used to source a timing reference which is used to generate a composite video output (for instance the PAL or NTSC output of a TANDBERG Television Receiver/Decoder) the accuracy of the resultant sub-carrier is directly traceable to the 27 MHz system clock in this equipment.
  • Page 314 Accuracy of Frequency Sources BLANK Page I-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 315 Annex J Use of Remux Card in ASTC Contents J.1 Remux Card In ATSC With Internal PSIP ... J-3 J.2 Remux Card In ATSC With External PSIP ... J-3 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder Page J-1 ST.TM.E10076.3...
  • Page 316 Use of Remux Card in ASTC BLANK Page J-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 317 Use of Remux Card in ASTC Remux Card In ATSC With Internal PSIP The Encoder automatically remuxes ATSC streams arriving at its inputs, as in DVB. The Encoder uses the PAT (Program Association Table) and PMT (Program Map Table) to work out all the associated PIDs (Packet Identifier), and attempt to extract the short name, the long name, and the Service Type from the VCT (Virtual Channel Table).
  • Page 318 Use of Remux Card in ASTC In this configuration the Encoder generates the PAT, CAT and PMT for all programs but it is the responsibility of the user to provide all the PSIP for the associated programs. Any programs present on the same input as the external PSIP are not detected and are not referenced in the PAT.

  • Page 319: List Of Tables

    Annex K EDH Capability for E57xx Encoders Contents K.1 EDH Capability for E57xx Encoders...K-3 List of Tables Table K.1: EDH Capability Matrix for E57xx Encoders... K-3 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder Page K-1 ST.TM.E10076.3...
  • Page 320 EDH Capability for E57xx Encoders BLANK Page K-2 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 321 EDH Capability for E57xx Encoders Table K.1 contains EDH capability for different mux firmware versions. To find the mux firmware version for a particular Encoder refer to Summary Screen/More/Advanced/Setup/System/Build Menu. Table K.1: EDH Capability Matrix for E57xx Encoders Mux F/W V14 and below Base Card Not Modified EDH does not work, no errors...
  • Page 322 EDH Capability for E57xx Encoders BLANK Page K-4 Instruction Manual: evolution 5000 E57xx DSNG and DENG Voyager Encoder ST.TM.E10076.3...
  • Page 323 This section is split into two parts. The first is the General Index and the second is devoted to Setup Menus and Associated Options. The following conventions are used in this manual: a page number entry in bold indicates a reference to a heading; a page number entry in italic is a reference to a table or figure;...
  • Page 324 Indexes background colour option, 4-34 backup configurations, 4-120 band plan option, 4-72 band plans, F-3, G-4 countries, F-3 manual option, F-3 bandwidth option, 4-45, 4-73, 4-86 basic interoperable scrambling system (BISS), 3-5 mode 1, 3-6, 4-95 battery disposal, 6-12 baud rate option, 4-67 beryllium, 2-5 BISS key entry option, 4-95...
  • Page 325 4-74 host bit-rate option, 4-96 HSYNC IN connector, 2-13 ident text option, 4-34 IF frequency option, 4-79 IF modulation e5714, 1-15 e5715, 1-15 e5740, 1-15 e5750, 1-15 IF output main connector, 2-18 monitor connector, 2-19 IF output option, 4-78, 4-87...
  • Page 326 Indexes changing from the front panel menus, 2-22 methods of changing, 2-21 IP address option, 2-22, 4-24 ip output card option, 3-27 IRD mode option, 4-104 IRD ts source option, 4-104 keyboard lock (softkeys), 4-13 keypad functions, 4-9 how to use, 4-14 softkey assignments, 4-14 keypress beep option, 4-27 language...
  • Page 327 option modules, B-20 16qam demodulator option, 3-26 additional audio input module, 3-6 basic interoperable scrambling system (BISS), 3-5 hardware, 3-3 how to see which are fitted/enabled, 3-5 ip output card option, 3-27 M2/EOM2/AUDLIN audio additional and linear PCM, B-20 M2/EOM2/DAT RS-232 and RS-422 data input, B-20 M2/EOM2/REMUX Remux, B-21 number, 3-4 positions, 3-3...
  • Page 328 Indexes sabus data bits option, 4-26 sat deliv freq option, 4-82, 4-85 sat orb pos option, 4-82, 4-85 sat west east option, 4-82 sat west/east option, 4-85 scramble option, 4-94 scrambling remote authorisation system (RAS), 4-89 screen saver option, 4-27 sd decoder option, 3-23 SDI (serial digital) video input connector error detection and handling (EDH), 1-8, 2-13...
  • Page 329 1, build info, 5-6 option 10, fault reporting, 5-11 option 2, tools, 5-7 option 3, customer support, 5-9 option 4, front panel (TANDBERG TV only), 5-9 option 5, backplane, 5-9 option 6, licenced features, 5-10 option 7, SNMP MIBS, 5-10...
  • Page 330 Indexes Setup Menus and Associated Options Index 1.service menu audio (MPEG-2) option, 4-103 BISS key code option, 4-101 CA input option, 4-100 data (type of data) option, 4-103 ECM (CA) PID option, 4-102 enc session word option, 4-101 logical channel option, 4-100 major channel option, 4-100 minor channel option, 4-100 name (in) option, 4-99...
  • Page 331 config name, 4-26 fan control, 4-28 keypress beep option, 4-27 local date, 4-26 local time, 4-26 model number, 4-26 power dip recovery option, 4-27 screen saver, 4-27 software release, 4-28 temperature, 4-27 upgrade encoder option, 4-28 UTC offset, 4-27 IRD demod menu FEC rate option, 4-106 frequency option, 4-106, 4-107 polarisation option, 4-107...
  • Page 332 Indexes remote control menu, 4-24 gateway address, 4-24 IP address, 4-24 last SNMP master, 4-25 last SNMP poll, 4-25 MAC address, 4-24 network mask, 4-24 sabus address, 4-25 sabus baud rate, 4-25 sabus data bits, 4-26 SNMP master, 4-25 SNMP trap IP, 4-25 remote control menu (syntax = DVB) serial protocol, 4-25 remux module menu...

This manual is also suitable for:

E5740E5715E5750Evolution 5000E5740-if

Table of Contents