F1345 is CE marked and fulfils IP21. frigerant circuit. The CE marking means that NIBE ensures that the product If the refrigerant circuit is breached /opened whilst the compressor is running, air can enter the process circuit. This can cause unusually...
Page 5
- Do not use charging bottles. These types of bottles change the composition of the refrigerant, which makes the performance of the system worse. - When filling refrigerant, the refrigerant must always leave the bottle in liquid form. NIBE™ F1345 Chapter 1 | Important information...
Tel./fax +7 831 419 57 06 NIBE AB Sweden, Box 14, Hannabadsvägen 5, SE-285 21 Markaryd Tel: +46-(0)433-73 000 Fax: +46-(0)433-73 190 For countries not mention in this list, please contact Nibe Sweden or check for more information. NIBE™ F1345 Chapter 1 |...
If a crane cannot be used F1345 can be transported on a sack truck. F1345 must be taken from its heaviest side (see printed material on packaging for where the centre of gravity is) and two people are required to lift F1345.
Assembly Supplied components Position F1345 on a firm base that can take the weight, See separate list of supplied components. preferably on a concrete floor or foundation. Use the Location product's adjustable feet to obtain a horizontal and stable set-up.
Electrical cabinets F1345 24 kW, 3x400 V F1345 30 kW, 3x400 V F1345 40 and 60 kW, 3x400 V Electrical components AA 10 Soft-start card FC 2 Motor cut-out QA 10 Contactor, compressor QA 11 Contactor, compressor Designations in component locations according to standard IEC 81346-1 and 81346-2.
Joint connector, compressor and motor module Cooling components EP 1 Evaporator EP 2 Condenser GQ 10 Compressor HS 1 Drying filter QN 1 Expansion valve Designations in component locations according to standard IEC 81346-1 and 81346-2. Chapter 3 | The heat pump design NIBE™ F1345...
Pipe installation must be carried out in accordance with pumps and control system with possibility of additional current norms and directives. F1345 can operate with a heat. F1345 is connected to the brine and heating medi- return temperature of up to 58 °C and an outgoing um circuits.
Caution Because the temperature of the brine system varies depending on the heat source, the menu 5.1.7 "br pmp al set." must be set to the suit- able value. NIBE™ F1345 Chapter 4 | Pipe connections...
Ethylene glycol 40% (volume percent) In installations with ethylene glycol (40% volume percent) as the brine the pressure expansion vessel must be dimen- sioned according to the following diagram. 800 1000 1200 1400 1600 1800 2000 Chapter 4 | Pipe connections NIBE™ F1345...
A climate system is a system that regulates indoor comfort Any docked hot water heater must be fitted with ne- with the help of the control system in F1345 and for ex- cessary set of valves. ample radiators, underfloor heating/cooling, fan con- The mixing valve must be installed if the setting is vectors etc.
Docking alternatives Gas boiler FL10 Safety valve, heating medium side F1345 can be connected in several different ways, some Auxiliary relay, external additional heat of which are shown below. QN11 Mixing valve, addition Further option information is available at EP21...
Page 21
Example - F1345 docked with electric additional heat and hot water heater (floating condensing) -EB1 -FL10 -CM5 -EB1 -EB100-BT25 -GP10 -QM42 -EB100-BT71 -RN11 -QM43 -RM42 -BP6 -QM21 -FL3 -EB100 -CM3 -BT1 -QM33 -EB100 -XL27 -XL28 -QM34 -EB100 -CP10 -FL12 -QN10...
Page 22
Example 2 - 2x F1345 docked with oil addition, pool and water heater (floating condensing) -EM1 -EP21 -AA5 -BT2 -GP20 -FL10 -KA1 -BT3 -QN25 -CM5 -AA5 -BT52 -EM1 -EB100-BT25 -GP10 -QN11 -EB100-BT71 -RM42 -BP6 -EB101 -QM21 -FL3 -EB101 -CL11 -CM3...
If the building is equipped with an earth-fault breaker, each F1345 should be equipped with a separate one. If a miniature circuit breaker is used this should have at least motor characteristic “C”. See page 40 for fuse size.
20 cm to high voltage cable when cable routing. Power connection F1345 must be installed via an isolator switch with a minimum breaking gap of 3mm. Minimum cable area NOTE must be dimensioned according to the fuse rating used.
Install the outside temperature sensor (BT1) in the shade A temperature sensor for hot water top (BT7) can be on a wall facing north or north-west, so it is unaffected connected to F1345 for showing the water temperature by the at the top of the tank (if possible).
Optional connections Master/Slave 1 2 3 4 Several heat pumps (F1345) can be interconnected by selecting one heat pump as master and the others as slaves. The heat pump is always delivered as master and up to till 8 slaves can be connected to it. In systems with several heat pumps each pump must have a unique name, that is only one heat pump can be ""Master"...
Load monitor Room sensor When many power consumers are connected in the F1345 can be supplemented with a room sensor (BT50). property at the same time as the electric additional heat The room temperature sensor has up to three functions: is operating, there is a risk of the property's main fuse 1.
If the relay is to be used for operating voltage, bridge the supply from terminal block X2:6 to X4:1 and connect neutral and operating voltage from the external additional heating to X2:8 (N) and X4:3 (L). Chapter 5 | Electrical connections NIBE™ F1345...
Temperature sensor, cooling/heating An extra temperature sensor can be connected to F1345 in order to better determine when it is time to switch between heating and cooling operation. The temperature sensor is connected to the selected input (menu 5.4, is only displayed if cooling accessory NIBE™...
An external contact function can be connected to tioned behind the front cover. F1345 for activation of one of the four fan speeds. The Tariff blocking means that the additional heat, the switch must be potential free and connected to the compressor and heating are disconnected by connect- selected input (menu 5.4) on terminal block X6.
NOTE See page 37 for the list of the accessories that can be used with F1345. An accessory card is required if several functions are connected to terminal block X5 at the same time that the buzzer alarm is activated (see page 37).
6 Commissioning and adjusting Preparations If the brine pumps must be run during venting, 1. Ensure that F1345 has not been damaged during they can be started via the start guide. transport. 2. Check that the switch (SF1) is in position "...
Caution In many menus there is a symbol that indicates that extra help is available. At startup of F1345-30 to 60 kW preheating of the compressors starts. Preheating continues To access the help text: until the temperature sensor BT29 is stable 10 1.
Set the speed of the brine pump in menu 5.1.9, (does Externt tillgängligt tryck not apply to F1345 40 and 60 kW). F1345 40 and 60 kW Set the speed of the brine pump as follows. In some countries the brine pump is not supplied, see list of supplied items.
Page 35
F1345 30 kW F1345 40 kW In some countries the brine pump is not supplied, see list Externt tillgängligt tryck of supplied items. Externt tillgängligt tryck 100% 100% Flöde, l/s 2 cirkulationspumpar 1 cirkulationspump Flöde, l/s Eleffekt per cirkulationspump Eleffekt per cirkulationspump 100% Flöde, l/s...
F1345 60 kW Pump capacity diagrams, heating medium side In some countries the brine pump is not supplied, see list of supplied items. To set the correct flow in the climate system the correct Externt tillgängligt tryck speed must be set for the heating medium pump in the different operating conditions.
F1345 60 kW Readjusting, venting, heat medium side Externt tillgängligt tryck Air is initially released from the hot water and venting may be necessary. If gurgling sounds can be heard from the heat pump or climate system, the entire system will require additional venting.
2 pipe, passive cooling 2 respectively 4 pipe External electrical addition ELK or if hot water comfort is to be connected to F1345. These accessories may require accessories card AXC 50 An accessory card is also required if the ground water (step controlled addition).
Page 40
F1345 is located. Part no. 067 064 Solar 42 Solar 42 means that F1345 (together with VPAS) can be connected to solar heating. Part no. 067 153 Chapter 7 | Accessories NIBE™...
2 x 2.4 Cut-out value pressostat HP 3.2 (32 bar) (42 bar) Difference pressostat HP -0.7 (-7 bar) Cut-out value pressostat LP 0.08 (0.8 bar) 0.2 (2 bar) Difference pressostat LP 0.07 (0.7 bar) Chapter 8 | Technical data NIBE™ F1345...
Page 43
With feet dismantled the height is approx. 1930 mm. This technical data applies to the brine pump supplied for 40 and 60 kW. NIBE™ F1345 Chapter 8 | Technical data...
Page 44
Working range heat pump, compressor oper- ation The compressor provides a supply temperature up to 65 °C. 3x400V 24 kW °C °C 3x400V 30 kW, 40 kW and60 kW °C °C Chapter 8 | Technical data NIBE™ F1345...
Page 76
Temperature sensor, hot water top, 23 The heat pump design, 8 Component list cooling section, 11 Component location cooling section, 11 Component locations, 8 List of components, 8 Transport, 6 Working range heat pump, 42 Chapter 9 | Item register NIBE™ F1345...