Utilitech #SE1019-WH3-02LF0-U Operating Instrctions page 2

PACKAGE CONTENTS
PARTS DESCRIPTION QUANTITY
A Fixture
B Dusk-to-Dawn Sensor
HARDWARE CONTENTS
Note: Hardware shown actual size.
AA BB
Machine Screw
Machine Screw
Mounting Bracket
Qty. 2
Qty. 4
(Not shown
SAFETY INFORMATION
Please read and understand this entire manual before attemting to assemble, operate or install the
product. SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR LIGHT FIXTURE SO
YOU CAN REFER TO THEM AT A LATER TIME.
WARNING
• Shut off power at the circuit breaker or fuse panel before removing the old fixture or installing
the new one.
CAUTION
• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If you currently have dimmer controls, you
will need to remove them and replace them with regular electrical switches. If you have a three-way
dimmer, you will have to replace it with a regular three-way switch. If you are unfamiliar with electrical
installations, it is recommended you have a qualified electrician do your installation.
PARTS DESCRIPTION
1 C Motion Sensor
1 D Wall Plate
CC DD EE
Grounding Screw
Qty. 1
Wire Nut
Qty. 3
to size)
Qty. 1
Lowes.com
2
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
1. Turn power OFF before installing or servicing.
2. Do NOT touch, operate, or install fixture while in contact with standing water.
3. Do NOT remove the protective LED lens.
4. Do NOT look directly at lighted LEDs for any length of time.
5. Do NOT leave bare wires exposed outside the wall canopy enclosure.
6. Electrical requirements: 120 V AC, 60 Hz. Minimum 90° supply conductors.
7. Suitable for wall or eave mounting onto recessed electrical boxes rated for wet locations. Not
suitable for ground mount installations or surface mounted electrical boxes.
8. Do NOT allow the sensor head to touch the LED light head housing. Maintain at least a 1 in.
spacing between the LED heads and the sensor head.
9. For proper operation and protection against water damage, the motion sensor adjustment controls
MUST be facing downward.
10. Do NOT mount below 5 ft.
11. Do not mount near other light sources that can compromise the dusk to dawn sensor.
12. This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
QUANTITY
Select the installation location carefully. Do not install in areas having pedestrian or motorized traffic,
1 pools or bodies of water, or trees/bushes that move in the wind. All of these will trigger the motion
sensor security light and may be disruptive to the intended operation of the light. Do NOT install near
1
other sources of light. The other light sources can fool the dusk to dawn sensor into thinking it is daylight.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to install the
product.
Estimated Assembly Time: 45 minutes.
FF
Tools Required for Assembly (not included): Phillips screwdriver and silicone caulking.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Silicone Cap
With power to the electrical box turned off, remove the old fixture. If the old fixture is attached to an
Qty. 2
electrical box that has more than two wire leads, mark the wires to keep track of the correct ones to use.
1. Trace the supply wires through the large center
opening of the mounting bracket (CC). Place the
mounting bracket over the electrical box, making sure
that the threaded mounting hole offsets are at the 12
and 6 o'clock position. Using the machine screws (AA
or BB) that fit the electrical box, secure the mounting
bracket to the electrical box.
Hardware Used
AA
Machine Screws
BB
CC Mounting Bracket
CC
x 2
x 1
Lowes.com
3
AA