Troubleshooting; Warranty - Utilitech #SE1019-WH3-02LF0-U Operating Instrctions

OPERATING INSTRUCTIONS
5. To be able to manually turn on the security light from
inside your home, toggle the wall light switch OFF and
ON within 2 seconds. The security light will turn on and
stay on for approximately 8 hours, or until the dusk-
to-dawn sensor detects light in the morning. Once the
dusk-to-dawn sensor detects light, the manual "ON"
mode will automatically go back to its original settings
of the AUTO motion sensor mode. At any point while in
manual "ON" mode, return to the AUTO motion sensor
mode by toggling the wall light switch OFF and ON
again within 2 seconds.
6. Once you have confirmed that the security light is
working properly, apply a small bead of silicone
caulking (not included) around the perimeter of the
rear housing cover to prevent water seepage into the
electrical compartment.
7. Press fit the silicone caps (FF) into the mounting
screw openings to prevent water seepage into the
housing.
Hardware Used
FF Silicone Caps
CARE AND MAINTENANCE
• Periodically clean the fixture and diffuser using a mild, non-abrasive glass cleaner and soft cloth. Do NOT
use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure you have the
power turned off and do not spray liquid cleaner directly onto any part of the fixture or LEDs.
SECURITY LIGHT OPERATION
MODE SLIDE SWITCH
Test Mode Test
AUTO Motion Sensor 1, 5, or 10 Minutes
Mode
Manual "ON" Mode 1, 5, or 10 Minutes
Return to AUTO Motion 1, 5, or 10 Minutes
Sensor Mode

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE
Light does not come on 1. No power is being
at night when motion delivered to the fixture.
is detected.
2. Another light source is
causing the security light
to think it is daylight.
3. Wiring inside electrical
came loose.
x 2
WALL SWITCH SENSITIVITY
Turn on Any setting
ON Any setting
Toggle OFF and ON Any setting
within 2 seconds
Toggle OFF and ON Any setting
within 2 seconds
CORRECTIVE ACTION A
1. Check that circuit breaker and/or wall
switch power is on.
2. Turn off surrounding lights and/or re-aim
the sensor head.
3. AFTER turning power off to the fixture,
reconnect any loose wiring.
6
TROUBLESHOOTING
PROBLEM
Security light comes
on during the day.
Security light cycles ON
and OFF continuously.
Security light comes
on for no apparent
FF
reason at night.

WARRANTY

A
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period
of (3) years from the date of original purchase by the consumer. We will repair or replace (at our option) the unit
in the original color and style if available, or in a similar color and style if the original item has been discontinued,
without charge. The manufacturer warrants the LEDs for 3 years, providing the fixture is not used in a commercial
application where it is on 24 hours per day, but is used in a residential environment for 3 - 5 hours per day.
Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your
original purchase receipt showing date of purchase. Call 1-866-994-4148 to obtain a return authorization number
and an address where to ship your defective product. Note: No C.O.D. shipments will be accepted. The liability of
the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will
not be liable for any other loss, damage, or injury which is caused by the product. This limitation upon the liability
of the manufacturer includes any loss, damage, or injury which is (I) to person or property or otherwise; (II)
incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability,
tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty
gives you specific rights, and you may also have other rights which vary from state to state.
POSSIBLE CAUSE CORRECTIVE ACTION
1. Dusk-to-dawn sensor is 1. Shine a flashlight onto the light sensor. If the
a shaded area and is security light turns off then the fixture is
fooled into thinking it mounted in an area that does not allow enough
is nighttime. light to enter the sensor. Relocate security light.
2. Dusk-to-dawn sensor 2. If under warranty, contact Customer Service.
is faulty.
1. Dusk-to-dawn sensor is 1. Change position of light head aim light
sensing reflected light away from the reflecting surfaces.
from the security light.
2. Put a small piece of black electrical tape over
the Dusk-to-dawn sensor control.
3. Relocate security light to a different location
where it no longer causes reflected light.
1. Light is sensing motion 1. Make sure the sensor is not picking up moving
in the detection zone. objects such as bushes, trees, traffic, water, etc.
2. Test the motion sensor by covering up the front
curved lens with cardboard to block the view. If
the light turns off then something in the
detection zone is triggering the sensor.
Reposition the motion sensor or change the
sensitivity (distance) of the sensor.
Utilitech & UT Design® are registered
trademarks of LF, LLC. All Rights Reserved.
7
A
Printed in China
Lowes.com