Pioneer VSX-49TX Service Manual page 178

VSX-49TX, VSX-47TX
Remote Control Unit (VSX-47TX)
These pages describe the buttons on the remote control used to operate the receiver.
1
S0URCE TV
2
DVD/LD TV
MULTI CONTROL
3
VCR1/
VCR2
DVR
CD-R/
CD
TAPE1
DIMMER INPUT ATT
1 2
4
VIDEO SEL SIGNAL SEL
5 6
TONE BASS/TREBLE
9 0
5
SYSTEM SETUP
MENU
6 TUNER EDIT
STATUS
7
GUIDE
MPX
¶
–
TUNING
8
1
–
STATION DTV MENU CLASS
4
–
CHANNEL
TV INPUT
TV CONTROL
9
TV VOL
TV CH
STANDARD
THX
0
SURROUND
ADVANCED ADVANCED
CINEMA CONCERT
(DVD-A/SACD)
-
ACOUSTIC MULTI CH
CAL INPUT
=
AV PRE-PROGRAMMED AND LEARNING
~
REMOTE CONTROL UNIT
1 Remote Control Display Screen
2 SOURCE button
Use this button to turn off other components. You
must input the preset code in order to use this
function .
TV button
This is a dedicated TV button. Use it to turn on/off
your TV.
3 MULTI CONTROL buttons
The mode of the receiver and allow you to control
your other components.
DVD/LD: Press to switch the remote control into
DVD/LD mode.
TV/SAT: Press to switch the remote control into
TV/SAT (satellite tuner) mode.
VCR 1: Press to switch the remote control into
VCR 1 mode.
VCR 2: Press to switch the remote control into
VCR 2 mode.
MD/TAPE 1: Press to switch the remote control
into MD/TAPE 1 mode.
CD: Press to switch the remote control into CD
mode.
TUNER: Press to switch the remote control into
TUNER mode.
178
SETUP
!
SYSTEM RECEIVER
@
OFF
SAT TV CONT
#
MULTI
VIDEO
OPERATION
$
TUNER RECEIVER
LOUDNESS SPEAKER A/B
3 4
TAPE 2 EFFECT/CH SELL
7 8
– + +
10 DISC
ENTER
DIRECT ACCESS DISP MODE
%
REMOTE SETUP
ENTER
EXIT
^
RETURN
DTV ON/OFF
8
EXTRA MENU
+
BAND TUNING
3 ¡
+
STATION
7 ¢
+
CHANNEL
&
INPUT
*
MIDNIGHT VOLUME
(
DIGITAL
NR
)
STEREO
MUTE
/DIRECT
LISTENING
MODE
_
LISTENING
LIGHT
CH SELECT
Î
AXD7290
TV CONTROL: Press so that the remote control can
operate the TV CONTROL commands.
4 Number buttons
These can be used for many purposes depending on the
mode of the receiver. When the in receiver mode the
buttons operate as below:
Display DIMMER
Use to adjust the brightness of the main display.
INPUT ATT. button
Use to lower the input level of an analog signal that is
too powerful, thus causing the receiver to distort (in this
case the overload indicator will be flashing furiously).
LOUDNESS button
Switches the LOUDNESS mode on or off (for all modes
except THX and MULTI CH IN).
SPEAKER A/B button
Use to select the speaker system. A is the primary
setting. It plays all speakers hooked up to the A system.
A & B setting only plays the front speakers of both the A
& B systems and the subwoofer. Multi channel sources
will be down-mixed to these speakers so no sound will
be lost. B setting only plays the front speakers connect-
ed to the B system and multi channel sources will be
down-mixed to these two speakers. The button cycles
through the speaker systems as follows:
A]B]A&B]off.
VIDEO SELECT button
Use to toggle between the different video input possibil-
ities.
SIGNAL SELECT button
Press SIGNAL SELECT repeatedly to select one of the
following:
ANALOG : To select an analog signal.
DIGITAL : To select a digital signal (DVD/LD, TV/SAT, CD,
MD/TAPE 1, VCR 1, VCR 2).
2 RF : To select an 2 RF signal (DVD/LD, TV/SAT, VCR 1,
VCR 2).
AUTO : This is the default. If there are analog, digital and
2 RF signals input, the receiver automatically selects the
2 RF signal. If there are analog and digital signals input the
digital will be selected.TAPE 2 MONITOR button (See p.57)
Selects the tape deck (or MD recorder, etc.) connected
to the TAPE 2 MONITOR inputs/outputs. Allows monitor-
ing of a recording as it's being made.
EFFECT/CH SEL. button
Switches the tone adjust controls between the front,
center, surround and surround back speakers. You can
then use the +and – buttons to adjust the sound.
TONE buttons
This button has two functions. Firstly, it switches
between TONE on and TONE DIRECT, which bypasses
the tone circuitry. Secondly, you need to press the
button before using the CHANNEL SELECT buttons to
adjust the BASS & TREBLE.