Advertisement
3" HIGH SPEED AIR CUTTER
ASSEMBLY AND OPERATING INSTRUCTIONS
(Cutting Disc not included)
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
2002 by Harbor Freight Tools
©
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements,
actual product may differ slightly from the product described herein. Tools required for assembly and service
may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
REV 09i
47077
. All rights reserved. No portion of this manual or any artwork
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Central Pneumatic 47077
Summary of Contents for Central Pneumatic 47077
- Page 1 3” HIGH SPEED AIR CUTTER 47077 ASSEMBLY AND OPERATING INSTRUCTIONS (Cutting Disc not included) Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Copyright 2002 by Harbor Freight Tools .
-
Page 2: Specifications
Wear a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up above elbows. REV 04i, 09i SKU 47077 For technical questions, please call 1-800-444-3353. Page 2... -
Page 3: Specific Product Warnings And Precautions
(1) of the Air Cutter. Turn on the air compressor, and set the regulator to the recommended 90 PSI for this tool. (See Figures A, B, and Assy. Diagram.) SKU 47077 For technical questions, please call 1-800-444-3353. Page 3... - Page 4 WARNING: Only use 3” Cutting Discs rated at more than 18,000 RPM and great- DO NOT USE UNAPPROVED ACCESSORIES. Do not use circular saw blades or wire brushes on this tool. Do not use any accessory except a 3” diameter Cut- ting Disc. SKU 47077 For technical questions, please call 1-800-444-3353. Page 4...
-
Page 5: Assembly Instructions
Use the Spanner (36) to hold the Spindle (32) in place while, at the same time, loosening and removing the Hex Bolt (35) and Flange (34) with the Hex Key Wrench (37). (See Figure B, and Assy. Diagram.) REV 04i; 07a SKU 47077 For technical questions, please call 1-800-444-3353. Page 5... -
Page 6: Operating Instructions
(3) and Safety Stick (7). (See Figure B, and Assy. Diagram.) Make sure the 3” cutting disc is not touching the surface of the workpiece. (See Figure B, and Assy. Diagram.) SKU 47077 For technical questions, please call 1-800-444-3353. Page 6... -
Page 7: Inspection, Maintenance, And Cleaning
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 47077 For technical questions, please call 1-800-444-3353. Page 7... -
Page 8: Parts List / Assembly Diagram
Hex Bolt Valve Screw Spanner Housing Hex Key Wrench (not included) NOTE: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 47077 For technical questions, please call 1-800-444-3353. Page 8... -
Page 9: Limited 1 Year Warranty
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 47077 For technical questions, please call 1-800-444-3353. Page 9...
Need help?
Do you have a question about the 47077 and is the answer not in the manual?
Questions and answers