Advertisement
Quick Links
®
AIR HIGH SPEED CUTTER
ASSEMBLY and OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd. / Camarillo, CA 93011
Copyright © 1997 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Advertisement
Related Manuals for Central Pneumatic 05490
Summary of Contents for Central Pneumatic 05490
- Page 1 ® AIR HIGH SPEED CUTTER ASSEMBLY and OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd. / Camarillo, CA 93011 Copyright © 1997 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
-
Page 2: Specifications
Do not use a tool for a purpose for which it was not intended. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in moving parts. Non-skid footwear is recommended. Wear restrictive hair covering to contain long hair. Page #2 -- SKU: 05490... - Page 3 Make sure that regulator is set at least 10 PSI lower than the lowest rated piece of equipment you are using. 20. The Safety Guard must always be tightly secured in place when using the Air High Speed Cutter. Keep hands off guard when operating this tool. Page #3 -- SKU: 05490 REV 02/04...
- Page 4 Step 3: Insert the HEX WRENCH (#31) into the HEX SCREW than 18,000 RPM. (#1) as shown in Figure 1. Cutting Wheel (#33) Spacer (#2) Hex Screw (#1) Hex Wrench (#31) Figure 1 — Inserting the Hex Wrench Page #4 -- SKU: 05490...
- Page 5 Spindle (#6) Spacer (#2) Hex Screw (#1) Hex Wrench (#31) High Speed Cutter Spanner (#32) Cutting Wheel (#33) Figure 2 — Replacing the Cutting Wheel Step 5:Remove the CUTTING WHEEL and replace with a new one. Page #5 -- SKU: 05490...
- Page 6 Step 10:Attach an Air Coupler (sold separately) to the Union fitting if desired. This is a useful accessory as it allows quick-coupling action when using a variety of tools with the same air compressor. Step 11:Your High Speed Cutter is ready for use. Page #6 -- SKU: 05490...
- Page 7 Warning: The Safety Guard must always be tightly secured in place when using the Air High Speed Cutter. Keep hands off guard when operating this tool. Page #7 -- SKU: 05490 REV 02/04...
- Page 8 Step 10:Keep a steady pressure on the High Speed Cutter as it cuts, but do not force the CUTTING WHEEL as you will stall the High Speed Cutter. Use only enough pressure to keep the CUTTING WHEEL moving through the material. Page #8 -- SKU: 05490...
-
Page 9: Maintenance
Step 4:Check the condition of the CUTTING WHEEL. Replace if necessary. Step 5: Wipe off the High Speed Cutter. Pay special attention to cleaning the PROTECTOR GUARD in order to be able to see your work when you cut. Page #9 -- SKU: 05490... -
Page 10: Parts List
Safety Latch Cylinder Throttle Lever Pin Rotor Collar Exhaust Deflector Rotor Inlet Bushing “O” Ring Rotor Blade Air Inlet Bushing Rear End Plate Hex Wrench Rear End Ball Bearing Spanner Motor Housing Cutting Wheel Valve Screw Page #10 -- SKU: 05490... -
Page 11: Assembly Diagram
ASSEMBLY DIAGRAM Page #11 -- SKU: 05490...
Need help?
Do you have a question about the 05490 and is the answer not in the manual?
Questions and answers