1. Manuals
  2. Brands
  3. ATD Tools Manuals
  4. Grinder
  5. 10556
  6. Instruction manual

ATD Tools 10556 Instruction Manual

6 inch bench grinder with lights
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
6 INCH BENCH GRINDER WITH LIGHTS
SPECIFICATIONS: 
• Model:  
  
• Rated Voltage:   
• Rated Input Power:   1/2 HP (1.5 A) 
• No Load Speed:  
• Wheel Size:    
• Shaft Diameter:  
• Includes: 36 grit grinding wheel, 60 grit grinding wheel, wire wheel and light bulbs  
ATD-10556
INSTRUCTION MANUAL
ATD10556 
120V AC, 60 Hz 
3550 RPM 
 6" diameter x 3/4" face x 1/2" bore  
1/2 in. 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 10556 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ATD Tools 10556

Summary of Contents for ATD Tools 10556

  • Page 1 ATD-10556 6 INCH BENCH GRINDER WITH LIGHTS INSTRUCTION MANUAL SPECIFICATIONS:  • Model:      ATD10556  • Rated Voltage:    120V AC, 60 Hz  • Rated Input Power:   1/2 HP (1.5 A)  • No Load Speed:   3550 RPM  • Wheel Size:      6” diameter x 3/4" face x 1/2” bore   • Shaft Diameter:   1/2 in.  • Includes: 36 grit grinding wheel, 60 grit grinding wheel, wire wheel and light bulbs  ...
  • Page 2 SAVE THIS MANUAL You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference. READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.

  • Page 3: Guidelines For Using Extension Cords

    • Do not abuse the cord. Never carry your tool by the cord or pull on the cord to unplug it. Protect the cord from potential sources of damage: heat, oil & solvents, sharp edges or moving parts. Damaged cords increase the risk of electric shock.
  • Page 4 WEAR YOUR SAFETY GLASSES- FORESIGHT IS BETTER THAN NO SIGHT WARNING! The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed.

  • Page 5: Specific Safety Rules For Bench Grinders

    • Store idle tools out of reach of children and other inexperienced persons. They are dangerous in the hands of untrained users. • Maintain power tools with care. Check for proper alignment and binding of moving parts, components, and any other conditions that may affect the tool’s operation.
  • Page 6 • Keep the spark guards close to the wheel and readjust them as the wheel wears. • Adjust tool rest distance from the grinding wheel to maintain a separation of 1/8 in. or less as the wheel diameter decreases from use. •...
  • Page 7 KNOW YOUR 6 INCH BENCH GRINDER A. On/off switch B. Base C. Motor housing D. Tool rest locking knob E. Mounting hole F. Left tool rest G. Wheel guard H. Side cover bolt Grinding wheel outer flange J. Side cover K.

  • Page 8: Unpacking And Contents

    UNPACKING AND CONTENTS IMPORTANT: Due to modern mass production techniques, it is unlikely the tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
  • Page 9 4. Adjust the spark guard to place its lower edge about 1/8 in. (3.2 mm) away from the grinding wheel face. 5. Adjust the eye shield bracket as well to accept and hold the eye shield correctly. 6. Rotate the wheel by hand at least one revolution to ensure the wheel turns without contacting with the spark guard.

  • Page 10: Operation

    CHANGE THE GRINDING WHEELS WARNING! Use only grinding wheels rated for the machine’s no-load speed (3550 RPM) or higher, which have a 1/2 in. arbor hole or a hole bushed to 1/2 in. Never use a grinding wheel rated for lower RPMs. Do not attempt to machine an undersized wheel to fit the arbor.

  • Page 11: Work Lights

    WORK LIGHTS Your grinder comes with two flex neck work lights which allow you to concentrate the light for better visibility of the work area during operation. The lights switch on with the grinder and stay on until it is turned off. WARNING! Always be sure that the tool is switched off and unplugged from the power source before adjusting, adding accessories, checking a function on the tool, and when leaving the work area.

  • Page 12: Maintenance

    • Always work using the face of the grinding wheel with the wheel’s surface moving downward into your work piece. • Do not use the side of the wheel to perform grinding operations. • Note the original bevel angle on the item sharpened and try to maintain this shape. MAINTENANCE CLEANING Avoid using solvents when cleaning plastic parts.

Table of Contents