ATD Tools ATD?10512 Instruction Manual

7” angle grinder

Advertisement

Quick Links

 
 
7" Angle Grinder Instruction Manual
Caution: Read this instruction manual before using this tool. 
 
Specifications 
 
Voltage: 120V/60Hz  
Amps: 11A 
No Load Speed: 7,800 RPM  
Max Accy Diameter: 7" 
Arbor Hole Diameter: 7/8" 
Safety Lock‐Off Switch: Yes  
Spindle Lock: Yes 
Spindle Thread: 5/8"‐11  
Cord Length: 6.5' 
Tool Weight: 7.5 lbs 
 
 
ATD‐10512 
 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ATD?10512 and is the answer not in the manual?

Questions and answers

Summary of Contents for ATD Tools ATD?10512

  • Page 1: Specifications

          ATD‐10512    7” Angle Grinder Instruction Manual   Caution: Read this instruction manual before using this tool.    Specifications    Voltage: 120V/60Hz   Amps: 11A  No Load Speed: 7,800 RPM   Max Accy Diameter: 7”  Arbor Hole Diameter: 7/8”  Safety Lock‐Off Switch: Yes   Spindle Lock: Yes  Spindle Thread: 5/8”‐11   Cord Length: 6.5’  Tool Weight: 7.5 lbs   ...
  • Page 2: General Power Tool Safety Warnings

    WARNING:     This product contains chemicals including lead, known to the State of California to  cause cancer, birth defects, or other reproductive harm.  Wash hands after handling.    WARNING:     Some dust created by power sanding, sawing, grinding, drilling and other  construction activities contains chemicals known to the State of California to cause cancer, birth defects,  or other reproductive harm.      Some examples of these chemicals are:  • Lead from lead based paint,  • Crystalline silica from bricks, cement, and other masonry products, and  • Arsenic and chromium from chemically treated lumber.      Your risk from exposure varies, depending on how often you do this work.  To reduce your exposure to  these chemicals:  work in a well‐ventilated area, and with approved safety equipment, such as dust  masks that are specifically designed to filter out microscopic particles.    General Power Tool Safety Warnings      WARNING Read all safety warnings and instructions. Failure to follow the  warnings and instructions may result in electric shock, fire and/or serious injury.  Save all warnings and instructions for future reference.  The term "power tool" in the warnings refers to your mains‐operated (corded) power tool or  battery‐operated (cordless) power tool.    1) Work area safety  a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.  b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,  gases or dust. Power tools create sparks which may ignite the dust or fumes.  c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose  control.  2) Electrical safety  a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter  plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of ...
  • Page 3: Safety Instructions For All Operations

    c) Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power  source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on  the switch or energizing power tools that have the switch on invites accidents.  d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left  attached to a rotating part of the power tool may result in personal injury.  e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the  power tool in unexpected situations.  f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from  moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.  g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are  connected and properly used. Use of dust collection can reduce dust‐related hazards.  4) Power tool use and care  a) Do not force the power tool. Use the correct power tool for your application. The correct power tool  will do the job better and safer at the rate for which it was designed.  b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be  controlled with the switch is dangerous and must be repaired.  c) Disconnect the plug from the power source and/or the battery pack from the power tool before making  any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the  risk of starting the power tool accidentally.  d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the  power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of  untrained users.  e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any  other condition that may affect the power tool’s operation. If damaged, have the power tool repaired  before use. Many accidents are caused by poorly maintained power tools.  f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less  likely to bind and are easier to control.  g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into  account the working conditions and the work to be performed. Use of the power tool for operations  different from those intended could result in a hazardous situation.  5) Service  a) Have your power tool serviced by a qualified repair person using only identical replacement parts.  This will ensure that the safety of the power tool is maintained.    Safety instructions for all operations  Safety Warnings for Grinding Operations:  a) This power tool is intended to function as a grinder. Read all safety warnings, instructions, illustrations  and specifications provided with this power tool. Failure to follow all instructions listed below may result  in electric shock, fire and/or serious injury.  b) Operations such as sanding, wire brushing, polishing or cutting‐off are not recommended to be  performed with this power tool. Operations for which the power tool was not designed may create a ...
  • Page 4: Kickback And Related Warnings

    h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or  safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable  of stopping small abrasive or work piece fragments. The eye protection must be capable of stopping  flying debris generated by various operations. The eye protection must be capable of stopping flying  debris generated by various operations. The dust mask or respirator must be capable of filtrating particles  generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.  i) Keep bystanders a safe distance away from work area. Anyone entering the work area must wear  personal protective equipment. Fragments of work piece or of a broken accessory may fly away and  cause injury beyond immediate area of operation.   j) Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting  accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may  make exposed metal parts of the power tool “live” and shock the operator.  k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and  your hand or arm may be pulled into the spinning accessory.  l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory  may grab the surface and pull the power tool out of your control.  m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory  could snag your clothing, pulling the accessory into your body.    n) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and  excessive accumulation of powdered metal may cause electrical hazards.    o) Do not operate the power tool near flammable materials. Sparks could ignite these materials.  p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in  electrocution or shock.    Kickback and Related Warnings  Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other  accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the  uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the  binding.  For example, if an abrasive wheel is snagged or pinched by the work piece, the edge of the wheel that is  entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick  out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s  movement at the point of pinching. Abrasive wheels may also break under these conditions.  Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be  avoided by taking proper precautions as given below.    a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback  forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction  during start‐up. The operator can control torque reactions or kickback forces, if proper precautions are  taken.  b) Never place your hand near the rotating accessory. Accessory may kickback over your hand. ...
  • Page 5 c) Wheels must be used only for recommended applications. For example: do not grind with the side of  cut‐off wheel. Abrasive cut‐off wheels are intended for peripheral grinding, side forces applied to these  wheels may cause them to shatter.  d) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper  wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut‐off  wheels may be different from grinding wheel flanges.  e) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not  suitable for the higher speed of a smaller tool and may burst.    ADDITIONAL SAFETY REGULATIONS  Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments.    Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other  accessories running over rated speed can fly apart and cause injury.    Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact  hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and  shock the operator.    When the machine is in operation, keep hands away from the grinding area.    The disc will not stop immediately the machine is turned off. Exercise caution.    Do not place the tool down after use until the grinding wheels have come to complete stop.    Do not start the tool when the grinding wheels are touching the work area.    Always ensure the safety guard is attached correctly and do not operate the angle grinder without the guard  attached.    Only use grinding wheels that are approved for a maximum speed of marked or greater.    Only use grinding wheels with the correct bore size for the spindle of the grinder.    Keep the power cord well away from the cutting area during use. Always position the cord so that it will not  be caught in the work piece when the grinder is in use.    Always wear earmuffs, safety glasses and face mask while in operation.    Before connecting the tool to the power supply follow the safety instructions to install the grinding   wheels.  Do not lock it too tight, otherwise cracks may occur. ...
  • Page 6 Tool specifications:  Rated  Voltage  Frequency  No‐load speed  Disc dia.  Spindle  Model  Current  (V)  (Hz)  (Min‐1)  (mm)  Thread  (A)  ATD‐10512  120  7800 7” 5/8”  1. Auxiliary handle       2. Spindle lock button  3. On/off switch      4. Square nut  5. Hex .screw  6. Grinding guard  7. Inner flange  8. Grinding disc  9. Outer flange  10. Spanner    2. Assembly    Warning: Switch off the grinder and disconnect it from the power point.    1) The auxiliary handle (1) can be screwed to the left or the right of Gear Box. Select the position which gives  the most comfortable and safe use.  ...
  • Page 7 Figure 1 Figure2 3) Fitting the grinding disc: (Figure 3 and Figure 4)  A. Place the inner flange (7) over the spindle making sure the fit is tight  B. Place  the  grinding  disc(8)  on  the  top  of  the  inner  flange  ensuring  the  bore  fits  into  the  step  of  the  flange  C. Mount the concave recess side of the outer flange (9) over the spindle  D. Press the spindle locking button (2) firm and ensure there is no movement in the spindle. While   the spindle lock is depressed, tighten the outer flange in a clockwise direction using the spanner (10).(See  figure 4)    Figure 3 Figure 4  ...
  • Page 8   Lock the tool in the “on” position  1) When starting hold the tool firmly with both hands i.e. one hand on the motor housing and the other  on the side auxiliary handle (1).  2) Start the  tool by pressing trigger inwards, and then press the  lock  button at side to lock the tool at  “on” condition. In this condition, the tool will operate continuously without pressing the trigger all the  time (See figure 5)  3) Stop the tool by actuating the switch trigger again.    4. Operating instructions    Note:   This angle grinder can be used for grinding steel, stone or ceramic work pieces such as pipe, box section,  rectangular, angle iron steel bar, household bricks and tiles. Do not attempt to grind wood or a soft metal such  as lead. The material will quickly “fill” the disc and render it useless.  Before starting the grinder first ensure that the disc, disc guard and tool are in good condition. Position the  guard so that it will deflect hot sparks away from the operator.    1) Do not cover vents when the tool is in use. This may cause damage to the motor and reduce the efficiency  of the tool.  2) Guide back and forth over the work piece in a steady motion.    Grinding   The best results are achieved with an angle of 20  to 30  for grinding. Move the  machine back and forth with light pressure. In this manner, the work piece does not  become too hot, no discoloration occurs and no ridges are produced.   Under no circumstances should a cutting disc be used for roughing work.         ...
  • Page 9  ...

This manual is also suitable for:

Atd-1051210512

Table of Contents