1. Manuals
  2. Brands
  3. ATD Tools Manuals
  4. Grinder
  5. ATD-10504
  6. Owner's manual

ATD Tools ATD-10504 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ATD-10504
Angle Grinder
Owner's Manual
Specifications
• Voltage: 120V/60Hz
• Amps: 8A
• No Load Speed: 11,000 RPM
• Wheel Size: 4-1/2" Diameter
• Safety Lock-Off Switch: Yes
• Spindle Lock: Yes
• Spindle Thread: 5/8"-11
• Cord Length: 6'
• Tool Weight: 6.5 lbs
WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer,
birth defects or other reproductive harm. Wash hands after handling.
(REV 02/17)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ATD-10504 and is the answer not in the manual?

Questions and answers

Related Manuals for ATD Tools ATD-10504

Summary of Contents for ATD Tools ATD-10504

  • Page 1 ATD-10504 Angle Grinder Owner’s Manual Specifications • Voltage: 120V/60Hz • Amps: 8A • No Load Speed: 11,000 RPM • Wheel Size: 4-1/2” Diameter • Safety Lock-Off Switch: Yes • Spindle Lock: Yes • Spindle Thread: 5/8”-11 • Cord Length: 6’...

  • Page 2: Know Your Product

    Know Your Product Alloy gear case Spindle lock button Lock-on slide switch On/off switch Side handle Adjustable safety guard 4 1/2” Grinding disc Safety guard adjustment bolt Pin spanner 10. Outer flange 11. Inner flange Safety Instructions Warning! When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage.

  • Page 3: Electric Safety

    Electric Safety The electric motor has been designed for 120V only. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by a qualified electrician or a power tool repairer in order to avoid a hazard.
  • Page 4 Personal safety Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Page 5 Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Safety Warnings Common for Grinding: This power tool is intended to function as a grinder. Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
  • Page 6 Further safety instructions for all operations: Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
  • Page 7 If you are fitting any other kind of attachment, refer to attachment fitting instructions. ATD Tools will not be responsible for any damage or injury caused due to the incorrect fitting of grinding or cutting discs or any other kind of attachment.

  • Page 8: Operation

    Operation Screw the outer flange (10) onto the spindle with the protruding ring section facing the angle grinder. This ring section must locate with the hole in the grinding disc (7). Tighten the outer flange (10) by locking the spindle (using the spindle lock button) and then tightening the outer flange (10) with the pin spanner (9) provided.

  • Page 9: Maintenance

    excessive heat. Such heat can cause rapid disc wear, fraying around the edge of the reinforced discs and disc breakage. Basic grinding procedure First ensure the work piece is securely held down (by both sides of the work piece if possible). Turn on the angle grinder and proceed to start grinding your work piece gently - do not “bump”...
  • Page 10 ATD-10504 ITEM# ORDERING PART# PART DESCRIPTION ITEM# ORDERING PART# PART DESCRIPTION PRT10504-01 OUTER FLANGE PRT10504-26 BEARING COVER PRT10504-02 INNER FLANGE PRT10504-27 SCREW M5X10 PRT10504-03 WHEEL GUARD φ115 PRT10504-28 ARMATURE PRT10504-04 SCREW M5X18 PRT10504-29 WIND BAFFLE PRT10504-05 SQUARE NUT M5 PRT10504-30 BALL BEARING 608.2Z...

Table of Contents