SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service transistors and semicounductor "chip" components. The manual and its supplements and addenda, read and follow the following techniques should be used to help reduce the SAFETY PRECAUTIONS on page 3 of this publication. incidence of component damage caused by static by static NOTE: If unforeseen circumstances create conflict between the electricity.
Page 5
c. Qulckly move the soldering iron tip to the junction of the Fuse and Conventional Resistor component lead and the printed circuit foil, and hold it Removal/Replacement there only until the solder flows onto and around both the 1. Clip each fuse or resistor lead at top of the circuit board component lead and the foil.
SPECIFICA TIONS Note : Specification and others are subject to change without notice for improvement. Video input system: PAL-B/G, D/K, I/I SOUND IF : 33.4MHz (B/G) SECAM-B/G, D/K,L/L’ 32.9MHz (I/I) NTSC M 32.4MHz (D/K) NTSC 4.43 34.4MHz (M) Intermediate Frequency (Unit : MHz) Power requirement : 110~240V, 50/60Hz VISION IF : 38.9MHz COLOR IF : 34.47MHz(4.43)
DECRIPTIONS OF CONTROLS All the functions can be controlled with the remote control handset. MUTE POWER Some functions can also be adjusted with the buttons on the front panel of the set. Remote control handset Before you use the remote control handset, please install the bat- teries.
10. MUTE POWER MUTE switches the sound on or off. 11. TV/AV selects TV or AV mode. clears the menu from the screen. switches the set on from standby. 12. Q.VIEW MENU TV/AV returns to the previously viewed programme. selects a favorite programme. 13.
Front panel CE/CL-21Q90K/91K/92K series CE/CL-21Q64K/65K/66K series TV/AV VIDEO AUDIO MENU SOUND ON/OFF TURBO ON/OFF DIG ITAL TURBO SO UND DI GITAL TURBO SOUND PICTURE 1 2 3 6 7 9 10 5 12 1 2 3 CE/CL-21Q60K/61K/62K series CE/CL-21Q20K/21K/22K series TV/AV ON/OFF TV/AV...
DISASSEMBLY INSTRUCTIONS Important note Chassis Assy Removal This set is disconnected from the power supply through the Grasp both side of Frame and pull it backward smoothly. converter transformer. An isolating transformer is necessary for service operations on the primary side of the converter transformer.
ADJUSTMENT Safety Precautions Option Code Function Remark 1. It is safe to adjust after using insulating transformer W/O TBS between the power supply line and chassis input to WITH TBS prevent the risk of electric shock and protect the instrument. W/O EYE 2.
Table below. 5) Press the OK( ) button to memorize the data. Status Initial Data Remark 6700VPF009G Tuner P/N 6700VPF016A LG Innotek(W/S TUNER) Marker DAEWOO(W/S TUNER) 2.7! 0.05V 2.7! 0.05V AGC Voltage 6700VPF009S Tuner P/N BLO-R...
Page 13
2. Deflection Initial Setup Data Status Default 21" FLAT S/S 21" FLAT LG 3. Deflection Adjustment Procedure VL (Vertical Linearity) Adjust so that the boundary line between upper and lower half is in accord with geometric horizontal center of the CPT.
PURITY & CONVERGENCE ADJUSTMENT Caution: 5. Reconnect the internal degaussing coil. Convergence and Purity have been factory aligned. Do not attempt to tamper with these alignments. 6. Position the beam bender locking rings at the 9 o'clock However, the effects of adjacent receiver components, or position and the other three pairs of tabs (2,4 and 6 pole replacement of picture tube or deflection yoke may require the magnets) at the 12 o'clock position.
Page 15
1.ADJUST YOKE Z-AXIS FIRST 2 .ADJUST BEAM BENDER 2 POLE TO GET EQUAL BLUE MAGNET TO GET FOUR EQUAL COLOR CIRCLES COLOR CIRCLES MAGNETS 8. Referring to above, perform the following two steps: 6. Reconnect the internal degaussing coil and apply AC power. a.
Page 16
ROTATION DIRECTION RING MOVEMENT OF RED OF BOTH TABS PAIRS AND BLUE BEAMS OPPOSITE POLE SAME OPPOSITE POLE SAME UP/DOWN ROCKING OF THE YOKE LEFT/RIGHT ROCKING OF THE YOKE UP/DOWN ROCKING OF THE YOKE LEET/RIGHT ROCKING OF THE YOKE CAUSES OPPOSITE ROTATION OF RED CAUSES OPPOSITE SIZE CHANGE OF THE CAUSES OPPOSITE ROTATION OF RED CAUSES OPPOSITE SIZE CHANGE OF...
The components identified by mark critical for safety. REPLACEMENT PARTS LIST Replace only with part number specified. LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q555 0TR534309AA TR,2SC5343Y TP AUK - - Q571 0TR198009BA TR,2SA1980Y TP AUK - - IC01 0ICTMPH006C TDA9361PS/N2/4I,0793 64P ST MC019A EURO/CIS TXT...
Page 21
The components identified by mark For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film critical for safety. digit in the P/No. means as CE : Electrolytic RN : Metal Film Replace only with part number specified.
Page 22
The components identified by mark For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film critical for safety. the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film digit in the P/No. means as CE : Electrolytic RN : Metal Film Replace only with part number specified.
Page 23
R662 0RD1000F609 100 OHM 1/6 W 5% TA52 R663 0RD1000F609 100 OHM 1/6 W 5% TA52 3828VA0378M MANUAL,OWNERS PL/SPEC LG PL 090A/D TX 017B R664 0RD1002F609 10K OHM 1/6 W 5% TA52 6710V00090A REMOTE CONTROLLERMC019A TXT LG NON R665 0RD3901F609 3.9K OHM 1/6 W 5% TA52...