Jiffy 30 Operating Manual/Parts Manual

Jiffy 30 Operating Manual/Parts Manual

Power ice drill 30 series

Advertisement

OPERATING MANUAL/PARTS GUIDE
This manual contains operating and safety instructions for the Jiffy
30 Series Power Ice Drill.
performance and satisfaction from your Jiffy Power Ice Drill, and to
reduce the risk of injury, it is important that you read and understand
the assembly, operating, maintenance, and safety instructions before
using your Jiffy Power Ice Drill.
Feldmann Engineering if you do not understand any of the
instructions in this manual.
As with any power tool, safety precautions must be observed with
the Jiffy Power Ice Drill to reduce the risk of personal injury.
Careless or improper use may cause serious injury and/or damage
to your Jiffy Power Ice Drill.
INDEX
General Information ..........................
Warranty.........................................
Pre-Use Procedure ...........................
Assembly of Drill...............................
Fueling............................................
Starting Instructions...........................
Transporting and Storage...................
...............
MANUFACTURER'S One Year Limited Warranty
(30 days for Commercial and/or Rental Use)
Feldmann Engineering & Manufacturing Co., Inc. warrants the Jiffy
Power Ice Drill to be made of first quality materials and workmanship
and will, at its option, repair or replace any drill part thereof found to
be defective in such materials and workmanship if returned to the
factory, prepaid within one year from the date of purchase by the
original purchaser. Inbound and outbound transportation charges are
paid by the purchaser.
Feldmann Engineering assumes no
responsibility for damage caused by misuse, careless handling, or
where repairs were made or attempted by an unauthorized person.
The engine and its operation are covered by the engine
manufacturer's warranty. For engine service or parts, contact your
local Tecumseh service outlet, phone
visit Tecumseh web site www. tecumsehpower.com
Jiffy 30 Series
Power Ice Drill
To receive the greatest possible
Contact your Jiffy dealer or
Page
Number
1
1
2
2
3
3
3
3
3
3
4
4
5
5
6
1-800-558-5402
SERVICE & REPAIR INFORMATION
For engine adjustments, repairs or warranty service not
covered in this manual, contact your nearest AUTHORIZED
TECUMSEH SERVICE OUTLET.
telephone book yellow pages under "Engines, Gasoline". If
you cannot find an Authorized Tecumseh Service Outlet near
you, call
1-800-558-5402
nearest
you,
www.tecumsehpower.com.
warranty service, Jiffy ice drill proof of purchase establishes
the date of sale and the start of the warranty period.
For non-engine related adjustments, repairs or warranty
service contact your nearest Authorized Jiffy Service Center
listed in the Jiffy Service Directory or call (920) 467-6167 for
locations
near
www.jiffyonice.com.
Manufactured by:
FELDMANN ENGINEERING &
MANUFACTURING CO., INC.
520 Forest Avenue
Sheboygan Falls WI 53085-2513
Phone: 920-467-6167
FAX: 920-467-6169
e-mail: admin@jiffyonice.com
www.jiffyonice.com
Other products include: TurfVent Lawn Aeration Equipment, BADGER Earth
Augers
, or
They are listed in your
to locate the Tecumseh outlets
or
visit
the
Tecumseh
you,
or
visit
our
Form #WM3070-06A (08/04)
web
site
at
When
requesting
web
site
at
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 30 and is the answer not in the manual?

Questions and answers

john michaud
January 22, 2025

change the coil on a model 30 jiffy ice auger

1 comments:
Mr. Anderson
May 14, 2025

To change the recoil (starter coil) on a Jiffy Model 30 ice auger:

1. Remove the recoil assembly: You may need to grind off rivets to detach it from the housing.
2. Replace or repair: Depending on the condition, either replace the entire recoil unit or repair internal components if possible.
3. Reattach: Secure the new or repaired recoil assembly back onto the housing using screws or rivets.

Note: Cold temperatures can cause the recoil to become stiff, which may be resolved by replacing worn parts or lubricating the mechanism.

This answer is automatically generated

Summary of Contents for Jiffy 30

  • Page 1: Table Of Contents

    Feldmann Engineering & Manufacturing Co., Inc. warrants the Jiffy Power Ice Drill to be made of first quality materials and workmanship and will, at its option, repair or replace any drill part thereof found to be defective in such materials and workmanship if returned to the factory, prepaid within one year from the date of purchase by the original purchaser.
  • Page 2: General Safety Precautions

    Gasoline is flammable and caution must be used when handling or storing it. Study the Do not fill the fuel tank while your Jiffy Power Ice Drill is running, if the Teach the safety engine is hot, or when your Jiffy Power Ice Drill is in an enclosed area.
  • Page 3: Assembly Of Drill

    DRILL ASSEMBLY TO POWERHEAD Attach drilling assembly to powerhead by sliding open end of drill shaft tube onto gear box output shaft. Align hole in drill shaft with hole in main gear assembly and affix by inserting sockethead capscrew (#2011) through hole in drill assembly collar and threading into hexnut (#2157).
  • Page 4: Operating/Stopping Instructions

    Figure 2 OPERATION/STOPPING INSTRUCTIONS NOTE: To minimize water splash, back-off throttle when the drill breaks Failure to follow these NOTE: The clutch slips when the drill is overloaded, when this NOTE: Remove blade protector from drill assembly prior to drilling.
  • Page 5: Maintenance And Adjustments

    For engine adjustment or repairs not covered in this section see the Service & Repair Information section below. IF ENGINE IS NOT TO BE USED FOR 30 DAYS OR MORE, PREPARE AS FOLLOWS: FUEL SYSTEM – Remove FUEL from CARBURETOR and FUEL TANK to prevent formation of gum deposits.
  • Page 6: Parts List

    30 SERIES PARTS LIST Includes: Model 30, Model 31 LEGEND™, Model 34 STEALTH™ & STEALTH STX™, FirePower™ and D-Ice’r ARMOR™ RIPPER™ Drill Assemblies REF. NO. PART NO. DESCRIPTION 3033 Fuel Tank Cap 2879 Wing Handle Half (For Model 30) “...

This manual is also suitable for:

31 legend34 stealth34 stealth stxFirepowerD-ice’r armor ripper

Table of Contents

Save PDF