Taylor 9523 Instructions

Taylor® 9523 Thermometer Instructions
Thank you for purchasing a Taylor® non-contact infrared thermometer. Please read this instruction manual carefully
before use. Keep these instructions handy for future reference.
Please remember to keep the unit away from children and do not use it for safety related applications.
Instructions
1. Simply aim the thermometer at the target with the Infrared Lens and press the
Measurement button to display the surface temperature.
2. The Distance:Spot is 6:1. Please make sure the target area is within the field
of view.
FEATURES:
o o
F or C switchable Press the "°C/°F" key to switch between
Backlight LCD Backlight: always on while the unit is on.
To enable the laser, press the "
LCD, indicating the laser is active. The laser sight will then operate when the Measurement
Laser
button is pressed. To disable the laser, press the "
Auto Off The unit will automatically turn off after 15 seconds of non-use to conserve battery power.
When the Measurement button is pressed, the unit will scan for surface temperatures and
update the reading on the LCD screen. When the Measurement button is released, the screen
Scan/Hold
will hold the last reading. The maximum temperature reading appears in the bottom of the
screen. (The maximum temperature reading will reset after each use.)
EMC/RFI
Readings may be affected if the unit is operated within a radio frequency electromagnetic field strength of
approximately 3 volts per meter, but the performance of the instrument will not be permanently affected.
o o
F and C temperature scales.
" button while the unit is on. The " " icon appears on the
" button while the unit is on.
CAUTION
1. WHEN THE DEVICE IS IN USE, DO NOT LOOK DIRECTLY INTO THE LASER BEAM, OR POINT THE LASER
TOWARDS ANYONE ELSE'S EYES, AS PERMANENT EYE DAMAGE MAY RESULT.
2. USE EXTREME CAUTION WHEN OPERATING THE LASER.
3. NEVER POINT THE DEVICE TOWARDS ANYONE'S EYES.
4. KEEP OUT OF REACH OF ALL CHILDREN.
STORAGE & CLEANING
The sensor lens is the most delicate part of the thermometer. The lens should be kept clean at all times. Take care
when cleaning the lens, using only a soft cloth or cotton swab with water or medical alcohol, and allow the lens to
fully dry before using the unit. Do not submerge any part of the thermometer. The thermometer should be stored at
room temperature between -4~140°F (–20 to +60°C).
LOW BATTERY INDICATIOR:
When the 'Low Battery' icon indicates the battery is low, the batteries should be replaced immediately with 2
AAA batteries. Please note: It is important to turn the instrument off before replacing the batteries, otherwise the
thermometer may malfunction. Dispose of used batteries properly and keep away from children. Always
replace both batteries at the same time; do not combine old and new batteries. Do not mix Alkaline, carbon-zinc
(standard) or Nickel-Cadmium (rechargeable) batteries. Remove the batteries if the unit will not be used for a
long period of time.
SPECIFICATIONS
Measurement Range
Operating Range
Accuracy
(-49 to +32°F / -45 to 0°C range)
Accuracy
(+32 to +149°F / 0 to +65°C range)
Accuracy
(above +149°F / +65°C range)
Emissivity
Resolution (-9.9~199.9°C)
Response Time (90%)
Distance:Spot
Battery Life
Dimensions
Weight
o o
-49 to +752 F (-45 to +400 C)
32 to 122°F (0 to 50°C)
o
+/- 1.8 + (.10 x (reading-32))°F
F
+/- 1°C + (.10 x reading)°C
+/- 1.8°F (+/-1°C)
+/- 1.5% of reading
0.95 fixed
0.1°F / 0.1°C
0.5 second
6:1
Approximately 16 hours
(186.8 x 43.6 x 85.7 mm)
7.35×1.72×3.37 inches
0.37 lb (169 g) including batteries (2 AAA)