Recommended Service Tools - Motorola MTX Series Service Manual

The following table lists the tools recommended for
working on this family of radios; these tools are also
available from Motorola. Note that the R-1319A
solder/desolder workstation requires the use of some
reflow nozzles. The nozzles' part numbers and general
descriptions are listed in the table with the R-1319A.
MOTOROLA PART NO.
0180381B45 110VAC
or
0180300E06 220VAC
8180369E97
1105139W02
0180386A81
0180386A78
0180386A82
6684253C72
6680384A98
1010041A86
R-1319A
(Supersedes R-1070A)
6680332E82
6680332E83
6680332E84
6680333E28
R-1070A
(Superseded by R-1319A)
HEAT-FOCUS
HEADS
6680334B49
6680334B50
6680334B51
6680334B52
6680334B53
6680370B51
6680370B54
6680370B57
6680370B58
6680371B15
6680371B74
6680332E45
6680332E46
* Refer to the SHIELDS LOCATION DETAIL and Shields Parts List in the rear of this manual to match the shield with the proper heat focus head.
4
Table 40-3. Recommended Service Tools
DESCRIPTION
MBT250 Surface-mount/
thru-hole repair station
Flux holder/applicator
30cc plastic syringe
and flux paste
Miniature digital readout
soldering station
(incl. 1/64" micropoint tip)
Illuminated magnifying glass
with lens attachment
Anti-static
grounding kit
Straight prober
Brush
Solder (RMA type),
63/37, 0.020" diameter-
1 lb. spool
Surface-Mounted Device
Rework Station
R-1319A Reflow Nozzle
R-1319A Reflow Nozzle
R-1319A Reflow Nozzle
R-1319A Reflow Nozzle
Shields and surface-mounted
component - IC removal/rework
station (order all heat focus
heads separately)
INSIDE DIMENSIONS
OF HEADS
0.410" x 0.410"
0.430" x 0.430"
0.492" x 0.492"
0.572" x 0.572"
0.670" x 0.790"
0.475" x 0.475"
0.710" x 0.710"
0.245" x 0.245"
0.340" x 0.340"
0.460" x 0.560"
0.470" x 0.570"
0.591" x 0.315"
0.862 x 0.350"
Also note that the R-1070A workstation requires the use
of a specific "heat focus head" for each of the compo-
nents on which this item is used. Each of these heat
focus heads must be ordered separately. The indi-
vidual heat focus heads (and the components on which
they are used) are listed at the end of the table.
APPLICATION
Temperature-controlled, self-contained soldering/desoldering
repair station for installation and removal of surface-mounted
devices.
Allows for the proper amount of flux to be applied to pad grid
arrays for repair.
For use with flux holder/applicator 8180369E97.
Used during all radio assembly and
disassembly procedures.
Removal of surface-mounted integrated circuits.
For IC removal (approximate size 0.8 in. x 0.8 in.)
For IC removal (approximate size 0.6 in. x 0.6 in.)
For IC removal (approximate size 0.5 in. x 0.5 in.)
For removal of RF PA
Removal of surface-mounted integrated circuits.
USED ON
U601, U702
U4, U5, U713
U3
U701, U705
* metal shields B, C, E, and F
U204
U710
U2, U201
U101, U102
* metal shields A, D, G, H, and I
U203
U714
U715
MAXIMUM PRESCRIBED
HEAT SETTING
Temperature settings
using the R-1319A and the
R-1070A are the same.
Refer to Maintenance Sec-
tion of Manual for
prescribed heat setting.