Advertisement
Advertisement
Related Manuals for Blendtec ez Blender
Summary of Contents for Blendtec ez Blender
- Page 1 Blender BRAWN. BRAINS. BLENDTEC.™...
-
Page 3: Table Of Contents
Table Of Contents Section Page Section 1 ..Important Safeguards Section 2..Component Overview Section 3..Unpacking Section 4..Installation Section 5..Operating Instructions Section 6..Warranty and Service Page 1... -
Page 4: Section 1 .....Important Safeguards
SECTION 1 – IMPORTANT SAFEGUARDS Read all instructions carefully before using your Blendtec machine. 1.1 SAFETY CERTIFICATION The ez Blender and accessories are certified by ETL to UL standard 763 and by CE Standards. 1.2 HEALTH CERTIFICATION The ez Blender and accessories are certified by NSF International. - Page 5 1.8 NEVER OPERATE IF THE UNIT APPEARS DAMAGED If the blender malfunctions call the service agent first. If it is dropped or damaged in any way, return the blender to a Blendtec service agent immediately for examination, repair, electrical or mechanical adjustment, or possible replacement.
-
Page 6: Section 2.....Component Overview
2.5 POWER SPECIFICATIONS The ez Blender is certified for use on 110/120 volt circuits and is limited to 13 amps. It is required that this unit be installed with a 15 amp protected circuit. Recommended protection for this unit is a 20 amp dedicated circuit. - Page 7 Page 5...
-
Page 8: Section 3.....Unpacking
5. Inspect all items to ensure no damage occurred in shipment. 6. If any damage has occurred contact your Blendtec service agent immediately. 3.2 RECORDING YOUR SERIAL NUMBER AND DATE OF SHIPMENT Record your blender base serial number and date of purchase in the space below. -
Page 9: Section 4.....Installation
SECTION 4: INSTALLATION 4.1 ez Blender Installation 1. Place blender base on a flat, clean, dry surface. 2. Make sure plug outlet is available within four feet of the motor base. 3. Plug the unit into a 120 volt receptacle with 15 amp protection. Make sure switch is turned off befor plugging in. -
Page 10: Section 5.....Operating Instructions
3. Press the button on the touchpad of your desired blender cycle. 5.2 AUTOMATIC CYCLE OPERATION If not otherwise specified, Blendtec blenders are programmed to the default Multipurpose blender program. See the Blendtec Cycle Chart included with this manual for details regarding programming and operation of your blender. - Page 11 If a jar is excessively noisy, or if the blade assembly seems loose or sounds “gravelly” when turned by hand, contact your Blendtec service center for assistance. BLENDED TEXTURE UNSATISFACTORY: If the blended texture of product is lumpy or uneven, do the following: ●...
- Page 12 TRIED EVERYTHING? If none of the preceding suggestions work, contact your Blendtec service agent for further assistance. 5.5 CLEAN BLENDER JAR DAILY 1. Using hot tap water, add 4 cups (1liter) of water and 1 1/2 teaspoons (7 ml) of liquid dish washing soap to the blender jar.
- Page 13 5.7 DAILY CLEANING OF MOTOR 1. Make sure the main power switch is off and motor is unplugged before cleaning. 2. When necessary, wipe the metal top and sides of the blender motor clean with a damp rag. Mild cleaners like WINDEX® may be used. 5.8 WEEKLY CLEANING OF MOTOR (Done in addition to daily cleaning while motor is unplugged and removed from enclosure) 1.
-
Page 14: Section 6.....Warranty And Service
SECTION 6: WARRANTY AND SERVICE PROCEDURE 6.1 WARRANTY DESCRIPTION Blendtec warrants the ez Blender base for 1 year or 5,000 cycles, whichever comes first. JAR: The polycarbonate jar and internal bearing assembly are warrantied against failure as follows: Jar Model... - Page 15 2. If the difficulty cannot be resolved over the phone, your unit may require repair. If you are under warranty, Blendtec will repair your unit at no cost. Cosmetic damage and abuse are not included.
- Page 16 1206 South 1680 West Orem, UT 84058 801-222-0888 www.blendtec.com OWN-CE-002 Manual, ez Blender Rev 01 07/06...
Need help?
Do you have a question about the ez Blender and is the answer not in the manual?
Questions and answers