Subscribe to Our Youtube Channel
Related Manuals for Excalibur REVERSE OSMOSIS DRINKING WATER SYSTEMS
Summary of Contents for Excalibur REVERSE OSMOSIS DRINKING WATER SYSTEMS
- Page 1 REVERSE OSMOSIS DRINKING WATER SYSTEMS INSTALLATION, OPERATION & SERVICE MANUAL 220 Bayview Drive, Unit 18 Barrie, ON L4N 4Y8 www.excaliburwater.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page INTRODUCTION PREPARATION A. Major System Components Installation Drawing B. Tools Recommended for Installation C. Site Selection For Major System Components INSTALLATION STEPS A. Faucet Installation Faucet Drawing B. Feed Water Ball Valve Installation C. Drain Clamp Installation D. -
Page 3: Introduction
INTRODUCTION The membrane is a specially constructed, Fully aromatic polyamide film, and is classified as a Your new Reverse Osmosis Drinking Water Thin Film Composite (T.F.C.). System uses a combination of filtration The spiral wound construction of the Reverse technologies to reduce unwanted contaminants in Osmosis Membrane provides maximum surface your water supply. -
Page 4: Preparation
PREPARATION A. Major System Components The following components comprise the Reverse 9. A Sediment Pre-filter, shrink wrapped. Osmosis Drinking Water System. (Refer to Fig. 1, 10.An activated Carbon Pre-filter, shrink below for general system layout.) wrapped. 1. A Reverse Osmosis Manifold assembly 11.An In-Line Activated Coconut Shell Carbon Post Filter. -
Page 5: Installation Drawing
BALL C. Site Selection for Major System Components... -
Page 6: Tools Recommended For Installation
C. Site Selection for Major System Components B. Tools Recommended for Installation The following tools will cover most of the The Reverse Osmosis System was designed to fit installation sites encountered: under a sink, however, because of space limitations or other reasons, the system's flexible design allows 1. -
Page 7: Installation Steps
4. Feed Water Connection – The Feed 2b. Drilling a porcelain sink: Water Ball Valve should be located as It is best to use a special 1¼" diameter cutter close to the manifold assembly as designed for porcelain. A carbide tipped possible. -
Page 8: Faucet Drawing
LONG REACH FAUCET Figure 2A... -
Page 9: Feed Water Ball Valve Installation
B. Feed Water Ball Valve Installation 3. With the Feed Water Ball Valve closed, Decide on location. Do NOT connect to a hot open the sink faucet and the water supply water feed line. If you are not sure of the and allow the water to run for a few minutes supply, run the hot water and feel the supply to flush any debris caused by the... -
Page 10: Drain Clamp Installation
C. Drain Clamp Installation 3. Locate the 3/8" Black Drain Tubing connected to the Reverse Osmosis Unit. Choose the drain outlet location. Route to the tubing to the Drain Clamp and trim to length. The following are instructions for discharging in the sink drain pipe. -
Page 11: Position The Drinking Water Holding Tank And Make The Final Hose Connections
• Slowly open the Feed Water Ball Valve D. Position the Drinking Water Holding Tank and Make the Final Hose Connections (turning counter clockwise). • As soon as the water begins to come out of 1. Check the tank pre-charge pressure. Make the Dispensing Faucet, close the Faucet. -
Page 12: Operation And Maintenance
OPERATION & MAINTENANCE Use a drip pan to catch any water that may spill when the Filter Housings are removed. Refer to A. Normal Operation Fig. 1, page 3 for component location. 1. Reverse Osmosis systems produce 1. Close the Feed Water Ball Valve by turning drinking water at relatively slow rates, it can fully clockwise and open the Dispensing take up to 3 hours to fill the Holding Tank. -
Page 13: Changing The In-Line Activated Carbon Post Filter
3 ml) into the tubing and reconnect it to the 5. Slowly open the Feed Water Ball Valve. Tee. 6. When water begins dripping out of the NOTE: Now is the convenient time to Faucet, in the following order, close the change the In-Line Activated Carbon Post Faucet and open the Holding Tank Filter. -
Page 14: Troubleshooting Guide
TROUBLE SHOOTING GUIDE Problem Possible Cause Solution Low quantity of Product Water Feed Water Ball Valve is plugged Open Valve or unclog. from Holding Tank or closed. Clogged Sediment Pre-filter or Replace filters. Activated Carbon Pre-filter. Low water pressure. Feed Water pressure must be above 40 psig. - Page 15 Problem Possible Cause Solution The Product Water and Drain Correct plumbing. High Total Dissolved Solids (TDS) in the Product Water Water lines are reversed. (continued) No drain flow, Drain Restrictor is Clear or replace Drain Restrictor. clogged. The ASO Valve is not closing. Repair or replace the ASO Valve Components.
Need help?
Do you have a question about the REVERSE OSMOSIS DRINKING WATER SYSTEMS and is the answer not in the manual?
Questions and answers