Manual Calling; Memory Calling; Receiving - Kenwood TRC-80 Instruction Manual

Group Communication Network Example
Predetermined frequency 14.482 MHz
Your Identification code 101
Member 1 Identification code 102
Member 2 Identification code 113
Member 3 Identification code 114
Group Group code 1
**
MANUAL CALLING
1 Adjust the SQUELCH control for the noise threshold
so the channel noise is just muted.
~
2 Activate Selective Call via Menu No. 06.
o "S.CALL" appears, and the receiveraudio is
muted.
S.CALL
-)
I
5 1 3 5 7 9
20 40 dB
RF 10
3 Hold down Microphone PTT and enter a 3-digit
Identification code via the Microphone keypad.
o
To make a call with a Group code, use "*" as a
wild card.
4 While still holding down Microphone PTT, enter "#".
o You can release Microphone PTT immediately
after pressing "#".
o The Identification code of the station being called
(their individual code or a Group code) plus your
Identification code is transmitted.
o
After the codes have been transmitted,the word
"CALL" plus the Identification code of the station
that was called are displayed. For example,
"CALL 102".
5 If you do not receive a response to your call within
about 10, 20, or 30 seconds (Dealer selectable),
your receiver mutes, and the radiotelephone is ready
to receive a selective call.
o
Instead of waiting for the programmedtime
period to pass, you can also press [I] again
(without pressing Microphone PTT) to restore the
radiotelephone standby status.
12
MEMORY CALLING
1 Adjust the SQUELCH control for the noise threshold
so the channel noise is just muted.
2 Activate Selective Call via Menu No. 06.
o
"S.CALL" a ppears, a ndthe receiver a udiois
muted.
\
S.CALL
!
S 1 3 5 7 9
20
40 dB
RF
10
\
3 Hold down Microphone PTT , then enter "*" plus "A",
"B", "C", or "D". For example, "*A".
4 While still holding down Microphone PTT, enter "#".
o You can release Microphone PTT immediately
after pressing "#".
o
The Identificationcode that is stored in memory
A, B, C, or D plus the Character message that is
stored for the same memory are sent. For
example, the Identification code and Character
message stored in memory A are sent.
o
After the code and message have been
transmitted, the word "CALL" plus the
Identification code of the station that was called
are displayed. For example, "CALL 102".
5 If you do not receive a response to your call within
about 10,20, or 30 seconds (Dealer selectable),
your receiver mutes, and the radiotelephone is ready
to receive a selective call.
o
Insteadof waiting for 10 seconds to pass, you
can also press [I] again (without pressing
Microphone PTT) to restore the radiotelephone
standby status.
RECEIVING
Adjust the SQUELCH control for the noise threshold so
the channel noise is just muted. After activating
Selective Call via Menu No. 06 and receiving a call, alert
beeps sound for about 10, 20, or 30 seconds (Dealer
selectable). Stop these beeps by pressing any button
or key. Pressing [I] stops the alert beeps and mutes
the receiver. Your Display may show either the
Identification code of the station calling you or a
Character message that the caller has sent. Pressing
[*] unmutes the receiver and allows you to monitor
channel activity.
If you receive a call while scanning, the r~ceiver
unmutes and stops on the channel for a period of time.
Pressing Microphone PTT during this period cancels the
alert beeps and the Scan function, and places the
radiotelephone in the transmit mode; pressing [SCAN]
cancels the alert beeps and the Scan function.
-
Your Menu
Menu#07
101
Menu#08 102
Menu#09
113
Menu#10
114
Menu#11
1**