Changing Identificationcodes; Changing Character Messages; Automaticantennatuner; Presetting(Kat-2Internaltuner) - Kenwood TRC-80 Instruction Manual

CHANGING IDENTIFICATION CODES
Your Identificationcode has been stored in Menu No. 07
by the Dealer. This code is fixed. However,the Dealer
also stored Identificationcodes for the stationswith
which you will communicate. Youcan use the
procedure below to change these codes. Acceptable
Group codes can be set by using "*" as a wild card
such as "10*", "*0*", "**4", or "*** ".
1 Press [MENU] to enter Menu mode.
2 Press [MODE] or [DATA] to select Menu No. 08, 09,
10, or 11.
3 Enter the first digit by turning the CHANNEL
selector,or by pressing a Microphone[UP] or
[DWN] key.
\
tN"
08
,\1/
I /71 /71
I ILl ILl
/1\
usa
4 Press [SCAN] to move to the next digit.
5 Enter the second digit.
6 Press [SCAN] to moveto the third digit.
7 Enter the third digit.
S Press [MENU] to exit Menu mode.
CHANGING CHARACTER MESSAGES
The Dealer may have programmedthe radiotelephone
so that it sends out Character messages insteadof the
radiotelephone'sIdentificationcode when you
communicate with other stations. The messages
programmed by the Dealer may be changed by you via
Menu mode.
1 Press [MENU] to enter Menu mode.
2 Press [MODE] or [DATA] to select Menu No. 12, 13,
14, or 15.
3 Enter a digit by turning the CHANNEL selector,or by
pressing a Microphone[UP] or [DWN] key.
MENU
]
4 Press [SCAN] to move to the next digit.
5 Repeat Steps 3 and 4 to enter up to 7 digits.
6 Press [MENU] to exit Menu mode.
AUTOMATIC ANTENNA TUNER
PRESETTING (KAT-2 INTERNAL T UNER)
After each successfultuning session, the Preset
function stores the data for the position of the tuning
capacitors. Then, if the channel is changed, the Preset
function automaticallypositionsthe capacitors using
data that was previouslystored for the new channel.
The first time that a channel is used,the Preset function
uses default data.
KAT-2 INTERNAL T UNER (OPTIONAL)
1 Press
[AT TUNE] to start tuning.
. ''TUNE''begins blinking.
iD
TUNE
s,
~ 51:. 20 40 dB
...............
RF 2 4 e 8 10
.
Pressing[AT TUNE] again cancels tuning.
2 Tuning completesand the Preset data is updated.
. ''TUNE''remainsvisible on the Display.
.
If tuning
does
not complete within approximately
20 seconds,five beeps sound over a 10 second.
period and the tuning action stops.
KAT-1/ MAT-100 E XTERNAL TUNER (OPTIONAL)
.
Always switch OFF the power to the radiotelephone
before connecting the KAT-1 or MAT-100 tuner.
1 Press [AT TUNE] to start tuning.
. ''TUNE'' begins blinking.
iD
TUNE
$1
~ sl;9
20 40 dB
...............
RF 2 4 6 8 10
.
Pressing[AT TUNE] again cancels tuning.
2 Tuning
completes.
. ''TUNE''remainsvisible
on the
Display.
.
If tuning does not complete within approximately
20 seconds, five beeps sound over a 10 second
period and the tuning action stops.
Note: Tuning with the KAT-1 or MAT-1 00 External Tuner does not
store any Preset data. Therefore, each time that a new channel is
selected, you must retune.
13