Mount The Camera - Panasonic BL-C20 Getting Started

4.

Mount the camera.

The camera can be mounted in the following ways.
Note
• Do not mount the camera where the sun light directly hits the camera or in
outdoor-type housing without a temperature control system. The camera may
malfunction due to high temperature.
• When you mount the camera, always hook the AC adaptor cord to the hook.
Hook for
AC adaptor cord
Stand Mount
Note
Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Stand/Tripod
Mounting Hole
Mounting Screw
Position Lock
Flexible
Stand
Ceiling Mount
Note
• Do not mount the camera upside down, since the image will be displayed
upside down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
• The included screws are only for a wooden ceiling.
• Mount the camera on a stable location such as a wooden column. Otherwise,
the camera may fall down and break.
Mount the Flexible Stand firmly to the
ceiling with the two screws (included).
Screws (included)
Allow sufficient space
between the wall and
the Flexible Stand to
turn the Position Lock.
• Do not mount the camera on a soft
material. The camera may fall and
be damaged.
• Use appropriate screws for the
material of the ceiling.
Adjust the angle, then fasten the
Position Lock.
Position Lock
Loosen the Position Lock located
on the rear side of the Flexible
Stand.
Turn the Mounting Screw to
attach the camera.
Adjust the angle, then
fasten the Position Lock.
Loosen the Position Lock located on
the rear side of the Flexible Stand,
and turn the Mounting Screw to
Wood
attach the camera.
20 mm
or more
Position Lock
Stand/Tripod
Mounting Hole
Connect the AC adaptor cord (and
Ethernet cable, if necessary) to the
camera and dress the cables neatly
and secure with tape (customer-
provided).
Tape
(customer-provided)
• This product is for indoor use only. Do not use it outdoors.
• The camera may become warm. This is not a malfunction.
Mount the camera where the AC adaptor can reach the power outlet, or use an
•
extension cord (customer-provided).
• Do not mount the camera upside down, since the image will be displayed upside
down.
Top
Bottom
Tripod Mount
Note
• Do not use a tripod screw with a
thread of 6 mm or more. This may
damage the Stand/Tripod Mounting
Hole.
• The camera cannot be mounted
depending on the shape of the
camera platform.
Wall Mount
Note
• Do not mount the camera upside down, since the image will be displayed
upside down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
• The included screws are only for a wooden wall.
• Mount the camera on a stable location such as a wooden column. Otherwise,
the camera may fall down and break.
Mount the Flexible Stand firmly to the
wall with the two screws (included).
Allow sufficient space between the
ceiling and the Flexible Stand to
turn the Position Lock.
Screws
(included)
Mounting
• Do not mount the camera on a soft
Screw
material. The camera may fall and
be damaged.
• Use appropriate screws for the
material of the wall.
Adjust the angle, then fasten the
Position Lock.
Position Lock
Make sure the indicator is
always in the upper right
corner.
Stand/Tripod
Mounting Hole
Tripod
(customer
-provided)
Loosen the Position Lock located on
the rear side of the Flexible Stand,
and turn the Mounting Screw to
attach the camera.
20 mm
or more
Wood
Indicator
Connect the AC adaptor cord (and
Ethernet cable, if necessary) to the
camera and dress the cables neatly
and secure with tape (customer-
provided).
Tape
(customer-provided)
Stand/Tripod
Mounting
Hole
Position
Lock
Mounting Screw