Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Citizen CZ series
Summary of Contents for Citizen CZ series
- Page 1 CITIZEN series Precision Balances...
- Page 2 CZ [NTEP ] User’s Guide - 9 -...
-
Page 3: Table Of Contents
Contents SECTION 1 INTRODUCTION………………………………………………………………1 SECTION 2 SPECIFICATIONS………………………………….…………………………2 SECTION 3 INSTALLATION……………………………………….……………..……….3 SECTION 4 KEY DESCRIPTIONS……………………………………..…………………4 SECTION 5 OPERATION…………………………………………….………………..…..5 5.1 Zeroing the display………………………………………….……………………..….5 5.2 Taring…………………………………………………………..……………………..….5 5.3 Weighing a sample………………………………………….…………………………5 5.4 Counter……………………………………………..…………….……………….…….5 SECTION 6 BATTERY OPERATION…………………………….……………..…………6 SECTION 7 PARAMETERS………………………………………….……….……………7 SECTION 8 APPENDIX…………………………………………….…………..…………9 9.1 Error code…………………..………………………………….………….…..……….9 9.2 Weighing unit listing………………………….……………..………….……………9 9.3 Explode drawing………………………….………………………..…………………10 9.4 Parts list………………………….……………………….…..…….…….……………11... -
Page 5: Section 1 Introduction
CZ Series Precision Balances service manual SECTION 1 INTRODUCTION CITIZEN’S CZ series of Precision balances provides an accurate, fast and versatile series of general purpose balances. There are 10 models in this series, with capacities from 500g~6000g, resolution from 5,000 to 120,000. -
Page 6: Section 2 Specifications
CZ Series Precision Balances service manual SECTION 2 SPECIFICATIONS 2.1 CZ series [ NTEP APPROVED ] NTEP Capacity Pan size n max Model CZ502 500 g 4.7” / 120 mm dia. 0.1 g 0.01 g 5000 CZ 501 500 g 4.7”... -
Page 7: Section 3 Installation
CZ Series Precision Balances service manual SECTION 3 INSTALLATION 3.1 GENERAL INSTALLATION The scales should be sited in a location that will not degrade the accuracy. Avoid extremes of temperature. Do not place in direct sunlight or near air conditioning vents. -
Page 8: Section 4 Key Descriptions
CZ Series Precision Balances service manual SECTION 4 KEY DESCRIPTIONS Zero or Set the zero point for all subsequent weighing. The display shows zero. A secondary function , of "Enter" key when setting parameters or other functions. Tare or Tares the scale. Stores the current weight in memory as a tare value, subtracts the tare value from the weight and shows the results. -
Page 9: Section 5 Operation
CZ Series Precision Balances service manual SECTION 5 OPERATION 5.1 ZEROING THE DISPLAY You can press the ZERO key at any time to set the zero point from which all other weighing and counting is measured, within 10% of power up zero. This will usually only be necessary when the platform is empty. -
Page 10: Section 6 Battery Operation
CZ Series Precision Balances service manual SECTION 6 BATTERY OPERATION When the battery needs change the indicator will turn on. Please change battery or use AC adapter after this indicator on. The scales can be operated from the battery if desired. The battery life is approximately 50 hours. -
Page 11: Section 7 Parameters
CZ Series Precision Balances service manual SECTION 7 PARAMETERS NOTE: If the user wants to enter into the technical parameter, the jumper K1 on the main board must be short firstly. The scale has 8 parameters that can be set by the user plus a method of entering the calibration section. - Page 12 CZ Series Precision Balances service manual Liner calibrate P1 LIN After you press ZERO key, display will show PIN again, press PRINT, S, P key and ZERO key to enter, display will show UNLOAD, remove all weight from the pan and wait until display show the calibrate weight value.
-
Page 13: Section 8 Appendix
CZ Series Precision Balances service manual SECTION 8 APPENDIX 9.1 ERROR CODES During the initial power-on testing or during operation it is possible the scale may show an error message. The meaning of the error messages is described below. If an error message is shown repeat the procedure that caused the message, turning the balance on, calibration or other functions. -
Page 14: Explode Drawing
CZ Series Precision Balances service manual 9.3 EXPLODE DRAWING - 9 -... -
Page 15: Parts List
CZ Series Precision Balances service manual 9.4 PARTS LIST No Parts name material Spec 1 Wind shielding top cover 1 AL 2 toughened glass 1 2 glass 152.5x80x3t 3 pole for glass 4 AL 4 toughened glass 2 2 glass 138.5x80x3t...
Need help?
Do you have a question about the CZ series and is the answer not in the manual?
Questions and answers