Related Manuals for Panasonic EY6535-U1
Summary of Contents for Panasonic EY6535-U1
-
Page 1: Specifications
ORDER NO. PTD0108U32C1 Cordless Multi Drill & Driver EY6535-U1 SPECIFICATIONS © 2001 Matsushita Electric Works Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. -
Page 2: Table Of Contents
EY6535-U1 CONTENTS Page Page 1 SCHEMATIC DIAGRAM 5 TROUBLESHOOTING GUIDE 2 WIRING CONNECTION DIAGRAM 6 EXPLODED VIEW 3 DISASSEMBLY INSTRUCTIONS 7 REPLACEMENT PARTS LIST 4 ASSEMBLY INSTRUCTIONS 1 SCHEMATIC DIAGRAM 2 WIRING CONNECTION DIAGRAM... -
Page 3: Disassembly Instructions
EY6535-U1 3 DISASSEMBLY INSTRUCTIONS IHOW TO DISASSEMBLE THE MAIN UNIT. Ref. No. 1A Procedure 1A Removal of Fixation Cover and Housing. 1. Remove 4 screws tightened with the fixation cover and take it out. 2. Remove clutch handle, slider and anvil. - Page 4 EY6535-U1 Ref. No. 1C Procedure 1A → → → → 1B → → → → 1C Removal of Motor Mounting Base. 1. To remove the ring gear, unhook right and left side of the projections using a flat screwdriver. 2. After removing the ring gear, the internal parts can be remove one after another.
- Page 5 EY6535-U1 Procedure 1A → → → → 1B → → → → 1D → → → → 1E Ref.No.1E Removal of Gear Case Assembly. 1. Take out the mode change handle. 2. Pull out 2 pins ( 2.5×33.6). 3. After removing pins, the internal parts of the gear case assembly can be removed one after another.
-
Page 6: Assembly Instructions
EY6535-U1 4 ASSEMBLY INSTRUCTIONS Ref.No.2A Procedure 2A Assembly of Gear Case Block. 1. Assemble thrust plate, clutch gear, planet gear (3pcs), carrier, thrust plate and insert pins (2pcs). 2. Reinstall one piece of steel ball into each of 6 holes. - Page 7 EY6535-U1 Procedure 2A→ → → → 2B Ref.No.2B Assembly of Motor Mounting Base. NOTE : After loosening these screws, please replace them with new screws. The old screws have an adhesive that can not be reapplied. New screws are identified with blue adhesive.
- Page 8 EY6535-U1 Ref.No.2C Procedure 2A→ → → → 2B→ → → → 2C Assembly of Gear Box Assembly. 1. Fit the driving carrier into the hole of the gear case assembly and the driving shaft assembly. 2. Confirm the connect piece is inside of the driving shaft block.
- Page 9 EY6535-U1 Procedure 2A→ → → → 2B→ → → → 2C→ → → → 2D→ → → → 2E Ref.No.2E Assembly of Housing. 1. Confirm proper position of the click springs and the position in each housing A and B.
-
Page 10: Troubleshooting Guide
EY6535-U1 5 TROUBLESHOOTING GUIDE (Refer to WIRING CONNECTION DIAGRAM) < TROUBLE > < CHECK > < REMEDY > Does not operate. <CHECK BATTERY PACK.> NO Replace battery pack. → If no less than 15.6 V DC is available across the (+) and (-) terminals, →... - Page 11 EY6535-U1 < TROUBLE > < CHECK > < REMEDY > No speed-control. <CHECK FET.> Replace switch & FET → → Even if FET block is defective, it can not be replaced individually. Replace block. whole switch block. Shortcircuit (G: gate) and (S: source), and measure between it and (D: drain) with switch block.
-
Page 12: Exploded View
EY6535-U1 6 EXPLODED VIEW... -
Page 13: Replacement Parts List
EY6535-U1 7 REPLACEMENT PARTS LIST NOTE: *A = available as an optional accessory *B = only available as set *C = available individually Ref. No. Part No. Part Name & Description Remarks Per Unit WEY6535K3078 HOUSING AB SET EY6481L0177 CLICK SPRING...
Need help?
Do you have a question about the EY6535-U1 and is the answer not in the manual?
Questions and answers