Advertisement
WARRANTY WILL BE VOID IF INSTRUCTIONS ARE NOT FOLLOWED.
Quartz Tube / Metal Sheath Element Installation:
Replacement elements which must be ordered separately are to be
installed by a qualified person. Wiring procedures and connections
shall be in accordance with the national and local codes having
jurisdiction.
CAUTION: Before removing or replacing a heating element,
turn controls to off and turn off power to heater circuit at main
disconnect panel. Lock the disconnect switch in the off (open)
position. Tag the circuit "Out for Maintenance" to prevent
potential lethal shock hazards. '
CAUTION: Quartz Elements can fracture and produce very
sharp edges and fragments. Use extreme care when handling
broken tubes or when handling new replacement elements.
1.
Remove the wire guard from the heater cabinet by
springing out to one side.
2.
Remove the two end reflectors held in place by 2 screws
each.
3.
Remove existing heating element. First, note the caution
statement below.
CAUTION: An old quartz heater should be treated as a
hazard. The material may chip and crack as with glass to
produce very sharp edges and fragments. Use appropriate
measures to protect skin and eyes to reduce the risk of
personal injury. When disposing of heating elements use
caution and comply with local and state regulations.
4.
Remove the quartz or metal tube heating element from its
packaging. Do not pull the quartz element by the white
ceramic terminal insulator.
CAUTION: Do not handle the Quartz tube heating
elements with bare hands or with gloves that may have
grease or oil present.
5.
Verify the correct heating element is being installed for
replacement.
Refer to the instructions below:
a.
The wattage, voltage and part number of the
replacement
compared with the markings on the heater and/or
the wattage, voltage and part number from the old
element.
b.
If electrical ratings or part number differ contact
an authorized factory service representative.
6.
For quartz tube heating elements: A paper wrapper is used
to keep debris away from the quartz tube during shipping
REPLACEMENT ELEMENT
heating
element
should
SAVE THESE INSTRUCTIONS
and installation. Leave the paper wrapping in place until
the element is completely installed to prevent finger marks
and/or grease and oil from transferring to the quartz tube.
7.
Carefully push the element into the two clips in the end
castings.
8.
Attach the lead wires to the heater terminals.
CAUTION: When tightening the nuts on the terminals,
ensure the terminals do not twist by holding the inner nuts
when tightening the outer nuts.
9.
For quartz heating elements: Remove wrapping paper.
CAUTION: Risk of Fire: Failure to remove paper wrapping
from quartz heating element will result in Fire.
10. Replace end reflectors and wire guard.
11. Refer to the operation section of owner's manual.
Replacement Element Specifications
TABLE 1 – Fixture 1154 Heating Elements:
Watts
Volts
1000
120
208
240
277
1500
120
208
240
277
2000
208
240
277
480
TABLE 2 – Fixture 1154A Heating Elements:
Watts
Volts
3000
208
be
240
277
480
4000
208
240
277
480
Page 6 of 6
Heater
Amps
Length
Quartz
8.3
QT-10L
36 "
4.8
QT-10V
(914mm)
4.2
QT-10N
3.6
QT-10Y
12.6
QT-15L
7.2
QT-15V
6.3
QT-15N
5.4
QT-15Y
9.6
QT-20V
8.3
QT-20N
7.2
QT-20Y
4.2
QT-20Z
Heater
Amps
Length
Quartz
14.4
QT-30N
61"
12.6
QT-30V
(1549 mm)
10.8
QT-30Y
6.3
QT-30Z
19.2
QT-40N
16.6
QT-40V
14.4
QT-40Y
8.3
QT-40Z
Metal
Sheathed
QM-10L
QM-10V
QM-10N
QM-10Y
QM-15L
QM-15V
QM-15N
QM-15Y
QM-20V
QM-20N
QM-20Y
QM-20Z
Metal
Sheathed
QM-30V
QM-30N
QM-30Y
QM-30Z
QM-40V
QM-40N
QM-40Y
QM-40Z
59-2000-83
Advertisement
