Table of Contents
Advertisement
3 IN 1 Vacuum
Blower-Mulcher
2400W
Instruction Manual
2 Year Replacement Warranty
BLV-2401
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
To view the full range visit:
www.ozito.com.au
0812
1
Advertisement
Table of Contents
Related Manuals for Ozito BLV-2401
Summary of Contents for Ozito BLV-2401
- Page 1 2400W Instruction Manual 2 Year Replacement Warranty BLV-2401 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
-
Page 2: Specifications
SPECIFICATIONS - MODEL NO. BLV-2401 Motor: 2400W Input: 230-240V ~ 50Hz No load speed: 10,000 - 15,000/min Air speed: 160 - 270km/h Max air volume: 12m³/min Mulching ratio: 10:1 Collection bag size: 40 Litres Weight: 3.4kg KNOW YOUR PRODUCT Secondary handle Mode selection lever 11. -
Page 3: Table Of Contents
TABLE OF CONTENTS Page 2 SPECIFICATIONS ……………………………………….. Page 4 INTRODUCTION………………………………………… Page 4 ELECTRICAL SAFETY…………….……………………… Page 5 GENERAL POWER TOOL SAFETY WARNINGS……… Page 7 BLOWER VAC SAFETY WARNINGS ……………..Page 9 ASSEMBLY……....…………………………… Page 11 OPERATION……………………………………………… Page 13 MAINTENANCE…………….…………………………… Page 14 SPARE PARTS …………….……………………………... Page 14 DESCRIPTION OF SYMBOLS …………………………. -
Page 4: Introduction
The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. -
Page 5: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool”... - Page 6 GENERAL POWER TOOL SAFETY WARNINGS d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 7: Blower Vac Safety Warnings
BLOWER VAC SAFETY WARNINGS It is recommend the blower vacuum be supplied via residual current device (RCD) with a tripping current not more than 30mA. Always wear adequate protective clothing when operating the tool to avoid injuries to face, eyes, hands, feet, head or hearing. Use safety glasses or a face shield, high boots or sturdy shoes, long trousers, work gloves, a hard hat and ear defenders. - Page 8 BLOWER VAC SAFETY WARNINGS 1) Training • Read the instructions carefully. Be familiar with the controls and the proper use of the appliance. • Never allow children to use the appliance. • Never allow people unfamiliar with these instructions to use the appliance. Local regulations may restrict the age of the operator.
-
Page 9: Assembly
ASSEMBLY WARNING! Before assembly, make sure that the blower vac is switched off and unplugged.. Assmbling the secondary handle (1) Insert secondary handle (1) to the blower vac and push until connected firmly (Fig. 1). Fig. 1 Assembling the tubes to the blower vac Insert the smaller lower tube (9a) into matching upper tube (10a) and push them together until they are connected firmly (Fig. - Page 10 ASSEMBLY ( cont Fitting the collection bag Prior to fitting the collection bag (7), the lower (9) and upper (10) tubes must be fitted to the motor housing. Attach the plastic connector on the collection bag (7) to the outlet in the housing, ensure that the two locating hooks “click”...
-
Page 11: Operation
OPERATION Starting the blower vac WARNING! Ensure the lower tube (9), upper tube (10) and collection bag (7) are fitted prior to plugging in the blower vac. To switch ON the blower vac press & hold the On/Off switch (4) (Fig. 9) To Switch OFF the blower vac release the On/Off switch (4) again. - Page 12 OPERATION ( cont Caution: Do not force the mode selection lever (6). The lever should move with very little resistance. If the lever is difficult to move, switch Off, disconnect the power supply, remove the collection bag (7), inspect the motor housing and ensure debris, dirt or mud has not jammed the lever.
-
Page 13: Maintenance
When not in use, the blower vac should be stored in a dry, frost free location not within the reach of children. Note: Ozito Industries will not be responsible for any damage or injuries caused by repair of the tool by an unauthorised person or mishandling or mistreatment of the tool. -
Page 14: Spare Parts
SPARE PARTS Limited spare parts are available subject to availability. Please contact your local Bunnings Special Orders Desk to order the required spare parts. Most common spare parts listed below Spare Part Part No. Collection Bag SPBLV2401-27 Shoulder Strap SPBLV2401-02 Support, Collection Bag SPBLV2401-26 DESCRIPTION OF SYMBOLS... -
Page 15: Pack Contents
Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice. CONTENTS 1 x Blower Vac BLV-2401 1 x Shoulder Strap 3 x Blower Tubes 1 x Collection Bag... - Page 16 OZITO INDUSTRIES PTY LTD AUSTRALIA (Head Office) 1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 Facsimile: +61 3 9238 5588 Website: www.ozito.com.au Email: enquiries@ozito.com.au...
Need help?
Do you have a question about the BLV-2401 and is the answer not in the manual?
Questions and answers
where does the soft bag inside the main bag fit