Related Manuals for DeWalt XR Li-Ion DCD995-XE
Summary of Contents for DeWalt XR Li-Ion DCD995-XE
-
Page 1: Instruction Manual
INSTRUCTION MANUAL DCD995-XE BRUSHLESS CORDLESS 13 mm (1/2") DRILL/DRIVER/HAMMERDRILL... -
Page 3: Definitions: Safety Guidelines
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ). Drilling into metal m/s² Technical Data Uncertainty K = m/s² DCD995-XE Vibration emission value a Voltage Impact drilling Power output m/s² 10.5 No-load speed Uncertainty K = m/s²... -
Page 4: Safety Instructions For Power Tools
An estimation of the level of exposure to vibration should also take into account 2) ELECTRICAL SAFETY the times when the tool is switched off or when it is running but not actually doing a) Power tool plugs must match the outlet. Never modify the plug in any the job. -
Page 5: Electrical Safety
e) Do not overreach. Keep proper footing and balance at all times. This b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. enables better control of the power tool in unexpected situations. c) When battery pack is not in use, keep it away from other metal objects like f) Dress properly. - Page 6 Drills/Drivers/Hammerdrills Safety Warnings • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. • Wear ear protectors when impact drilling. Exposure to noise can cause hearing Your risk from these exposures varies, depending on how often you do this type of loss.
-
Page 7: Important Safety Instructions For All Battery Packs
SAVE ALL WARNINGS AND INSTRUCTIONS FOR WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery FUTURE REFERENCE pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose Important Safety Instructions for All Battery Packs nails, screws, keys, etc. - Page 8 NOTICE: Under certain conditions, with the charger plugged into the power supply, the • Disconnect the charger from the outlet before attempting any cleaning. This charger can be shorted by foreign material. Foreign materials of a conductive nature, will reduce the risk of electric shock. Removing the battery pack will not reduce such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any this risk.
-
Page 9: Charge Indicators
Charge Indicators 2. The charger and battery pack may become warm to the touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the This charger is designed to detect certain problems that can arise. Problems are cooling of the battery pack after use, avoid placing the charger or battery pack in indicated by the red light flashing at a fast rate. -
Page 10: Assembly And Adjustments
2. For long storage, it is recommended to store a fully charged battery pack in a FIG. 2 cool dry place out of the charger for optimal results. NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use. - Page 11 Side Handle (Fig. 2) FIG. 3 FIG. 4 FIG. 5 WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle properly installed. Failure to do so may result in the side handle slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.
-
Page 12: Operation
Your tool features a keyless chuck with one rotating sleeve for one-handed operation WARNING: To reduce the risk of serious personal injury, ensure the screw of the chuck. To insert a drill bit or other accessory, follow these steps. holding the belt hook is secure. 1. - Page 13 FUEL GAUGE BATTERY PACKS (FIG. 10) FIG. 10 WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is Some D WALT battery packs include a anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to fuel gauge which consists of three green prevent damage to the material.
-
Page 14: Maintenance
Hammerdrill Operation (Fig. 5) CHARGER CLEANING INSTRUCTIONS WARNING: Shock hazard. Disconnect the charger from the AC outlet before 1. Select the desired speed/torque range using the gear shifter to match the speed cleaning. Dirt and grease may be removed from the exterior of the charger using a and torque to the planned operation. - Page 16 The battery voltage is nominal, it can measure above or below depending on the state of charge. Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (OCT13) Part No. N341799 DCD995-XE Copyright ©...