Related Manuals for DeWalt XR Li-Ion DCD771-XE
Summary of Contents for DeWalt XR Li-Ion DCD771-XE
-
Page 1: Instruction Manual
INSTRUCTION MANUAL DCD771-XE CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER DCD776-XE CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER/HAMMERDRILL... -
Page 3: Definitions: Safety Guidelines
Vibration emission value a CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ). Drilling into metal Technical Data m/s² <2.5 <2.5 Uncertainty K = m/s² DCD771-XE DCD776-XE Voltage Vibration emission value a Screwdriving Battery type Li-Ion Li-Ion m/s²... -
Page 4: Safety Instructions For Power Tools
accessories or poorly maintained, the vibration emission may differ. This may c) Keep children and bystanders away while operating a power tool. significantly increase the exposure level over the total working period. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY An estimation of the level of exposure to vibration should also take into account a) Power tool plugs must match the outlet. -
Page 5: Electrical Safety
d) Remove any adjusting key or wrench before turning the power tool on. A to be performed. Use of the power tool for operations different from those wrench or a key left attached to a rotating part of the power tool may result in intended could result in a hazardous situation. -
Page 6: Extension Cords
– Children should be supervised to ensure that they do not play with the appliance. WARNING: ALWAYS wear approved protective safety equipment complying with • Replacement of the supply cord. If the supply cord or plug is damaged, it must the following standards: be replaced by the manufacturer or an authorised D WALT Service Centre in... -
Page 7: Important Safety Instructions For All Battery Packs
min ....minutes or AC ....alternating current or metal buildings in summer). For best life store battery packs in a cool, dry location. or DC ..direct current or AC/DC ..alternating or NOTE: Do not store the battery packs in a tool with the trigger switch locked ....Class I Construction ......direct current on. -
Page 8: Important Safety Instructions For All Battery Chargers
Important Safety Instructions for All Battery Chargers • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal SAVE THESE INSTRUCTIONS: This manual contains important safety and operating heat. -
Page 9: Charge Indicators
Important Charging Notes 3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the 1. Longest life and best performance can be obtained if the battery pack is charged charger. -
Page 10: Storage Recommendations
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE COMPONENTS (FIG. 2, 8) DCD771-XE WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. A. Trigger switch F. - Page 11 Worklight (Fig. 2) NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided. There is a worklight (E) located just above the trigger switch (A). The worklight is activated when the trigger switch is depressed. When the trigger is released, the Forward/Reverse Control Button (Fig.
-
Page 12: Operation
Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the FUEL GAUGE BATTERY PACKS (FIG. 7) FIG. 7 tool for maximum tightness. Some D WALT battery packs include a To release the accessory, repeat steps 1 and 2 above. fuel gauge which consists of three green LED lights that indicate the level of charge OPERATION... -
Page 13: Maintenance
9. With variable speed drills there is no need to center punch the point to be drilled. WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is Use a slow speed to start the hole and accelerate by squeezing the trigger harder anchored or clamped firmly. - Page 14 Lubrication Your power tool requires no additional lubrication. Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear AS/NZS1337 approved eye protection when performing this.
- Page 16 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (OCT13) Part No. N376052 DCD771-XE, DCD776-XE Copyright © 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...